View A3P1000_1565029.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

august 2008 i ? 2008 actel corporation military proasic3/el low-power flash fpgas with flash*freeze technology features and benefits military temperature tested and qualified ? each device tested from ?55c to 125c firm-error immune ? not susceptible to neutron-induced configuration loss low power ? dramatic reduction in dynamic and static power ? 1.2 v to 1.5 v core and i/o voltage support for low power ? ? low power consumption in flash*freeze mode allows for instantaneous entry to / exit from low-power flash*freeze mode ? ? supports single-voltage system operation ? low-impedance switches high capacity ? 600 k to 3 m system gates ? up to 504 kbits of true dual-port sram ? up to 620 user i/os reprogrammable flash technology ? 130-nm, 7-layer metal (6 copper), flash-based cmos process ? live-at-power-up (lapu) level 0 support ? single-chip solution ? retains programmed design when powered off high performance ? 350 mhz (1.5 v systems) and 250 mhz (1.2 v systems) system performance ? 3.3 v, 66 mhz, 66-bit pci (1.5 v systems) and 66 mhz, 32-bit pci (1.2 v systems) in-system programming (isp) and security ? secure isp using on-chip 128-bit advanced encryption standard (aes) decryption via jtag (ieee 1532?compliant) ?flashlock ? to secure fpga contents high-performance routing hierarchy ? segmented, hierarchical routing and clock structure ? high-performance, low-skew global network ? architecture supports ultra-high utilization advanced and pro (professional) i/os ?? ? 700 mbps ddr, lvds-capable i/os ? 1.2 v, 1.5 v, 1.8 v, 2.5 v, and 3.3 v mixed-voltage operation ? ? bank-selectable i/o voltages?up to 8 banks per chip ? single-ended i/o standards: lvttl, lvcmos 3.3 v / 2.5 v / 1.8 v / 1.5 v / 1.2 v, 3.3 v pci / 3.3 v pci-x, and lvcmos 2.5 v / 5.0 v input ? ? differential i/o standards: lvpecl, lvds, blvds, and m-lvds ? voltage-referenced i/o standards: gtl+ 2.5 v / 3.3 v, gtl 2.5 v / 3.3 v, hstl class i and ii, sstl2 class i and ii, sstl3 class i and ii (a3pe3000l only) ? i/o registers on input, output, and enable paths ? hot-swappable and cold-sparing i/os ? programmable output slew rate and drive strength ? programmable input delay (a3pe3000l only) ? schmitt trigger option on single-ended inputs (a3pe3000l) ? weak pull-up/-down ? ieee 1149.1 (jtag) boundary scan test ? pin-compatible packages across the military proasic?3el family clock conditioning circuit (ccc) and pll ? six ccc blocks, one with integrated pll (proasic3) and all with integrated pll (proasic3el) ? configurable phase shift, multiply/divide, delay capabilities, and external feedback ? wide input frequency range 1.5 mhz to 250 mhz (1.2 v systems) and 350 mhz (1.5 v systems) srams and fifos ? variable-aspect-ratio 4,608-bit ram blocks (1, 2, 4, 9, and 18 organizations available) ? true dual-port sram (except 18) ? 24 sram and fifo configurations with synchronous operation: ? 250 mhz: for 1.2 v systems ? 350 mhz: for 1.5 v systems arm ? processor support in proasic3/el fpgas ? arm cortex?-m1 soft proces sor available with or without debug ? ? A3P1000 only supports 1.5 v core operation. ? flash*freeze technology is not available for A3P1000. ?? pro i/os are not available on A3P1000. table 1-1 ? military proasic3/el low-power devices proasic3/el devices a3pe600l A3P1000 a3pe3000l arm cortex-m1 devices 1 m1A3P1000 m1a3pe3000l system gates 600 k 1 m 3 m versatiles (d-flip-flops) 13,824 24,576 75,264 ram kbits (1,024 bits) 108 144 504 4,608-bit blocks 24 32 112 flashrom bits 1 k 1 k 1 k secure (aes) isp 2 yes yes yes integrated pll in cccs 616 versanet globals 18 18 18 i/o banks 848 maximum user i/os 270 154 620 package pins pqfp fbga fg484 pq208 fg144 fg484, fg896 notes: 1. refer to the cortex-m1 product brief for more information. 2. aes is not available for arm-enabled proasic3/el devices. v1.0 www..net
military proasic3/el low-power flash fpgas ii v1.0 i/os per package 1 proasic3/el low-power devices a3pe600l A3P1000 a3pe3000l arm cortex-m1 devices m1A3P1000 m1a3pe3000l package single- ended i/o 2 differential i/o pairs single- ended i/o 2 differential i/o pairs single- ended i/o 2 differential i/o pairs pq208 ??15435?? fg144 ? ? 97 25 ? ? fg484 270 135 ? ? 341 168 fg896 ? ? ? ? 620 300 notes: 1. when considering migrating your design to a lower- or hi gher-density device, refer to the packaging section of the datasheet to ensure you are complying with design and board mi gration requirements. 2. each used differential i/o pair reduces the nu mber of single-ended i/os available by two. 3. "g" indicates rohs-compliant packages. refer to "military proasic3/el ordering information" on page iii for the location of the "g" in the part number. 4. for a3pe3000l devices, the usage of cert ain i/o standards is limited as follows: ? sstl3(i) and (ii): up to 40 i/os per north or south bank ? lvpecl / gtl+ 3.3 v / gtl 3.3 v: up to 48 i/os per north or south bank ? sstl2(i) and (ii) / gtl+ 2.5 v/ gtl 2.5 v: up to 72 i/os per north or south bank 5. when the flash*freeze pin is used to di rectly enable flash*freeze mode and not as a regular i/o, the number of single- ended user i/os available is reduced by one. www..net
military proasic3/el lo w-power flash fpgas v1.0 iii military proasic3/el ordering information s pee d g ra d e blank = s tan d ar d 1 = 15% faster than s tan d ar d A3P1000 f g _ part num b er military proa s ic3/el devi c e s 1 pa c ka g e type 144 m pa c ka g e lea d c ount g lea d -free pa c ka g in g appli c ation (temperature ran g e) m = military ( ? 55 c to 125 c j un c tion temperature) blank = s tan d ar d pa c ka g in g g = roh s - c ompliant ( g reen) pa c ka g in g 6 00,000 s ystem g ates a3pe 6 00l = 1,000,000 s ystem g ates A3P1000 = 3,000,000 s ystem g ates a3pe3000l = military proa s ic3/el devi c e s with arm cortex-m 1 1,000,000 s ystem g ates m1A3P1000 = 3,000,000 s ystem g ates m1a3pe3000l = f g = fine pit c h ball g ri d array (1.0 mm pit c h) pq = plasti c qua d flat pa c k (0.5 mm pit c h) www..net
military proasic3/el low-power flash fpgas iv v1.0 temperature grade offerings speed grade and temperature grade matrix contact your local actel represen tative for device availability: http://www.actel.com/c ontact/default.aspx . package a3pe600l A3P1000 a3pe3000l arm cortex-m1 devices m1A3P1000 m1a3pe3000l pq208 ?m? fg144 ?m? fg484 m?m fg896 ??m note: m = military temperature range: ?55 c to 125c junction temperature temperature grade std. ?1 m ?? note: m = military temperature range: ?55 c to 125c junction temperature www..net
v1.0 1-1 1 ? military proasic3/el device family overview general description the military proasic3/el family of actel fl ash fpgas dramatically reduces dynamic power consumption by 40 % and static power by 50 % . these power saving s are coupled with performance, density, true single chip, 1.2 v to 1.5 v core and i/o operation, reprogrammability, and advanced features. actel's proven flash*free ze technology enables military proasic3el device users to shut off dynamic power instantaneously and switch the devi ce to static mode without the need to switch off clocks or power supplies, a nd retaining internal states of th e device. this greatly simplifies power management. in addition, optimized soft ware tools using power-driven layout provide instant push-button power reduction. nonvolatile flash technology gives military proasic3/el devices the advantage of being a secure, low-power, single-chip solution that is live at po wer-up (lapu). military proasic3/el devices offer dramatic dynamic power savings, giving fpga users flexibility to combine low power with high performance. these features enable designers to create high-den sity systems using existi ng asic or fpga design flows and tools. military proasic3/el devices offer 1 kbit of on-chip, reprogrammable, nonvolatile flashrom storage as well as clock conditioning circuitry (ccc) based on an integrated phase-locked loop (pll). military proa sic3/el devices support devices from 6 00 k system gates to 3 million system gates with up to 504 kbits of true dual-port sram and 620 user i/os. m1 military proasic3/el devices support the hi gh-performance, 32-bit cortex-m1 processor developed by arm for implementation in fpgas. ar m cortex-m1 is a soft processor that is fully implemented in the fpga fabric. it has a three-st age pipeline that offers a good balance between low-power consumption and speed when implemented in an m1 military proasic3/el device. the processor runs the armv6-m instru ction set, has a configurable ne sted interrupt controller, and can be implemented with or without the debug block. arm cortex-m1 is available at no cost from actel for use in m1 military proasic3/elfpgas. the arm-enabled devices have actel ordering numbers that begin with m1 and do not support aes decryption. flash*freeze technology ? military proasic3el devices offer actel's proven flash*fr eeze technology, which allows instantaneous switching from an active state to a static state. when flash*freeze mode is activated, military proasic3el devices enter a stat ic state while retaining the contents of registers and sram. power is conserved with out the need for additional exte rnal components to turn off i/os or clocks. flash*freeze technology is combin ed with in-system programmability, which enables users to quickly and easily upgrade and update thei r designs in the final stages of manufacturing or in the field. the ability of military proasic3el devices to support a 1.2 v core voltage allows for an even greater reduction in power consumption, which enab les low total system power. when the military proasic3el device enters flas h*freeze mode, the device automatically shuts off the clocks and inputs to the fp ga core; when the device exits flash*freeze mode, all activity resumes and data is retained. the availability of low-power mode s, combined with a reprogrammable, single-chip, single-voltage solution, make military proasic 3el devices suitable for low-power data transfer and manipulation in military-temperature applications where ava ilable power may be limited (e.g., in battery- powered equipment); or where heat dissipation may be limited (e.g., in en closures with no forced cooling). ? flash*freeze technology is not supported on A3P1000. www..net
military proasic3/el device family overview 1-2 v1.0 flash advantages low power ? the military proasic3el family of actel flash- based fpgas provides a low-power advantage, and when coupled with high performance, enables desi gners to make power-smart choices using a single-chip, reprogrammable, and live-at-power-up device. military proasic3el devices offer 40 % dynamic power and 50 % static power savings by reducing the core operating voltage to 1.2 v. in addition , the power-driven layout (pdl) feature in libero ? integrated design environm ent (ide) offers up to 30 % additional power reduction. with flash*freeze technology, military proasic3el device is able to retain device sram and logic while dynamic power is reduced to a minimum, withou t the need to stop cloc k or power supplies. combining these features provid es a low-power, feature-rich, and high-performa nce solution. security nonvolatile, flash-based military proasic3/el devices do not require a boot prom , so there is no vulnerable external bitstream that can be easily copied. military proasic3/el devices incorporate flashlock, which provides a unique combination of reprogrammability and de sign security without external overhead, advantages th at only an fpga with nonvolatile flash programming can offer. military proasic3/el devices utilize a 128-bit fl ash-based lock and a separate aes key to secure programmed intellectual property and configur ation data. in addition, all flashrom data in military proasic3/el devices can be encrypted prior to loading, using the industry-leading aes-128 (fips192) bit block cipher encryption standard. aes was adopted by the national institute of standards and technology (nist) in 2000 and repl aces the 1977 des standard. military proasic3/el devices have a built-in aes decryption engine and a flash-based aes key that make them the most comprehensive programmable logic de vice security solution available today. military proasic3/el devices with aes-based security allow for secure, re mote field updates over public networks such as the internet, and ensure that valuable ip remain s out of the hands of system overbuilders, system cloners, and ip thieves. the contents of a progra mmed device cannot be read back, although secure design verification is possible. security, built into the fpga fabric, is an inhere nt component of the military proasic3/el family. the flash cells are located beneath seven meta l layers, and many device design and layout techniques have been used to make invasive atta cks extremely difficult. the military proasic3/el family, with flashlock and aes secu rity, is unique in being highly resistant to both invasive and noninvasive attacks. your valuab le ip is protected and secure, making remote isp possible. a military proasic3/el device pr ovides the most impenetrable se curity for programmable logic designs. single chip flash-based fpgas store their configuration information in on-chip flash cells. once programmed, the configuration data is an inherent part of the fpga structure, and no external configuration data needs to be loaded at system power-up (u nlike sram-based fpgas). therefore, flash-based military proasic3/el fpgas do not require syste m configuration componen ts such as eeproms or microcontrollers to load device configuration da ta. this reduces bill-of-materials costs and pcb area, and increases securi ty and system reliability. live at power-up actel flash-based military proasic3/el devices supp ort level 0 of the lapu classification standard. this feature helps in system component initializat ion, execution of crit ical tasks before the processor wakes up, setup and configuration of memory blocks, clock generation, and bus activity management. the lapu feature of flash-based milita ry proasic3/el devices greatly simplifies total system design and reduces total system cost, of ten eliminating the need for cplds and clock generation plls. in addition, glitches and browno uts in system power will not corrupt the military proasic3/el device's flash configuration, and unlike sram-based fpgas, the device will not have to be reloaded when system power is restored. this enables the reduction or complete removal of the configuration prom, expensive voltage monitor, brownout detection, and clock generator devices from the pcb design. flash-based military proasic3 /el devices simplify to tal system design and ? A3P1000 only supports 1.5 v core operation. www..net
military proasic3/el de vice family overview v1.0 1-3 reduce cost and design risk whil e increasing system reliability and improving system initialization time. reduced cost of ownership advantages to the designer extend beyond lo w unit cost, performance, and ease of use. unlike sram-based fpgas, flash-based mi litary proasic3/el devices allow all functionality to be live at power-up; no external boot prom is required. on-board security mechanisms prevent access to all the programming information and en able secure remote updates of the fpga logic. designers can perform secure remote in-system reprogramming to supp ort future design iterations and field upgrades with confidence that valuable intellec tual property cannot be compromised or copied. secure isp can be performed using the industry-st andard aes algorithm. the military proasic3/el family device architecture mitiga tes the need for asic migration at higher volumes. this makes the military proasic3/el family a cost-effective asic replacement. firm-error immunity firm errors occur most commonly when high-energ y neutrons, generated in the upper atmosphere, strike a configuration cell of an sram fpga. the energy of the coll ision can change the state of the configuration cell and thus change the logic, routing, or i/o behavior in an unpredictable way. these errors are impossible to prev ent in sram fpgas. the consequenc e of this type of error can be a complete system failure. firm errors do not exist in the configuration memory of military proasic3/el flash-based fpgas. once it is prog rammed, the flash cell configuration element of military proasic3/el fpgas cannot be altered by high-energy neutrons and is therefore immune to them. recoverable (or soft) errors oc cur in the user data sram of all fpga devices. these can easily be mitigated by using error dete ction and correction (edac) circui try built into the fpga fabric. advanced flash technology the military proasic3/el family offers ma ny benefits, including nonvolatility and reprogrammability, through an ad vanced flash-based, 130-nm lvcmos process with 7 layers of metal. standard cmos design techniques are used to implement logic and control functions. the combination of fine granularity, enhanced flexible routing resour ces, and abundant flash switches allows for very high logic util ization without compro mising device routability or performance. logic functions within the device are intercon nected through a four-level routing hierarchy. advanced architecture the proprietary military proasic3/el architecture provides granularity comp arable to standard-cell asics. the military proasic3/el device consists of five distinc t and programmable architectural features ( figure 1-1 on page 1-4 and figure 1-2 ): ? fpga versatiles ? dedicated flashrom ? dedicated sram/fifo memory ? extensive cccs and plls ? i/o structure the fpga core consists of a sea of versatiles. ea ch versatile can be configured as a three-input logic function, a d-flip-flop (with or without enable), or a latch by programming the appropriate flash switch interconnections. the ve rsatility of the military proasic3/e l core tile, as either a three- input lookup table (lut) equivalent or a d-flip-f lop/latch with enable, al lows for efficient use of the fpga fabric. the versatile capability is unique to the actel proasic family of third-generation- architecture flash fpgas. versatiles are connected wi th any of the four levels of routing hierarchy. flash switches are distributed throughout the device to provide nonvolatile, reconfigurable interconnect programming . maximum core utilization is possible for virtually any design. www..net
military proasic3/el device family overview 1-4 v1.0 in addition, extensive on-chip programming circ uitry allows for rapid, single-voltage (3.3 v) programming of military proasic3/el devices via an ieee 1532 jtag interface. figure 1-1 ? military proasic3 device architecture overview with four i/o banks (A3P1000) figure 1-2 ? military proasic3el device architec ture overview (a3pe600l and a3pe3000l) ram block 4,608-bit dual-port sram or fifo block ram block 4,608-bit dual-port sram or fifo block versatile ccc i/os isp aes decryption user nonvolatile flashrom charge pumps bank 0 bank 3 bank 3 bank 1 bank 1 bank 2 4,608-bit dual-port sram or fifo block versatile ram block ccc pro i/os 4,608-bit dual-port sram or fifo block ram block isp aes decryption* user nonvolatile flashrom flash*freeze technology charge pumps www..net
military proasic3/el de vice family overview v1.0 1-5 flash*freeze technology ?? military proasic3el devices offer actel's proven flash*freeze technology, which enables designers to instantaneously shut off dy namic power consumption while retaining all sram and register information. flash*freeze techno logy enables the user to quic kly (within 1 s) enter and exit flash*freeze mode by activating the flash*freeze (ff) pin while al l power supplies are kept at their original values. in addition, i/os and global i/os can still be driven and can be toggling without impact on power consumption; clocks can still be driven or can be toggling without impact on power consumption; all core registers and sram ce lls retain their states. i/os are tristated during flash*freeze mode or can be set to a certain st ate using weak pull-up or pull-down i/o attribute configuration. no power is consumed by the i/o banks, clocks, jtag pins, or plls. flash*freeze technology allows the user to switch to active mode on de mand, thus simp lifying the power management of the device. the ff pin (active low) can be routed internally to the core to allow the user 's logic to decide when it is safe to transition to this mode. it is al so possible to use the ff pin as a regular i/o if flash*freeze mode usage is not planned, which is advantageous because of the inherent low- power static and dynamic capabilities of the military proasic3el device. refer to figure 1-3 for an illustration of entering/exiting flash*freeze mode. versatiles the military proasic3/el core co nsists of versatiles, which have been enhanced beyond the proasic plus ? core tiles. the milita ry proasic3/el versatile supports the following: ? all 3-input logic functions?lut-3 equivalent ? latch with clear or set ? d-flip-flop with clear or set ? enable d-flip-flop with clear or set refer to figure 1-4 for versatile configurations. ?? flash*freeze technology is not supported for A3P1000. figure 1-3 ? military proasic3el flash*freeze mode a c tel proa s i c 3el fp g a flash * freeze mo d e c ontrol flash * freeze pin figure 1-4 ? versatile configurations x1 y x2 x3 lut-3 data y clk enable clr d-ff data y clk clr d-ff lut-3 equivalent d-flip-flop with clear or set enable d-flip-flop with clear or set www..net
military proasic3/el device family overview 1-6 v1.0 user nonvolatile flashrom actel military proasic3/el devices have 1 kbit of on-chip, user-accessible, nonvolatile flashrom. the flashrom can be used in diverse system applications: ? internet protocol addressing (wireless or fixed) ? system calibration settings ? device serialization and/or inventory control ? subscription-based business mode ls (for example, set-top boxes) ? secure key storage for secu re communicati ons algorithms ? asset management/tracking ? date stamping ? version management flashrom is written using the standard mili tary proasic3/el ieee 1532 jtag programming interface. the core can be individually programmed (erased and written), and on-chip aes decryption can be used selectively to securely lo ad data over public networks, as in security keys stored in the flashrom for a user design. flashrom can be programmed via the jtag programming interface, and its contents can be read back either through the jtag prog ramming interface or via direct fpga core addre ssing. note that the flashrom can only be prog rammed from the jtag interface and cannot be programmed from the internal logic array. flashrom is programmed as 8 banks of 128 bits; however, reading is performed on a byte-by-byte basis using a synchronous interfac e. a 7-bit address from the fpga core defines which of the 8 banks and which of the 16 bytes within that ba nk are being read. the th ree most sign ificant bits (msbs) of the flashrom address determine the bank , and the four least sign ificant bits (lsbs) of the flashrom address define the byte. the actel military proasic3/el deve lopment software solutions, libero ide and designer, have extensive support for the flas hrom. one such feature is au to-generation of sequential programming files for applications requiring a unique serial number in each part. another feature allows the inclusion of static data for system version contro l. data for the flashrom can be generated quickly and easily using actel libero ide and designer software tools. comprehensive programming file support is also included to allo w for easy programming of large numbers of parts with differing flashrom contents. sram and fifo military proasic3/el devices have embedded sram blocks al ong their north and south sides. each variable-aspect-ratio sram block is 4,608 bits in size. available memory configurations are 25618, 5129, 1k4, 2k2, and 4k1 bits. th e individual blocks have indepe ndent read and write ports that can be configured with different bit widths on each port. for example, data can be sent through a 4-bit port and read as a single bitstream. the embedded sram bl ocks can be initialized via the device jtag port (rom emulation mode) using the ujtag macro. in addition, every sram block has an embedded fifo control unit. the control unit allows the sram block to be configured as a synchronous fi fo without using additional core versatiles. the fifo width and depth are programmable. the fifo also features programmable almost empty (aempty) and almost full (afull) flags in additi on to the normal empt y and full flags. the embedded fifo control unit cont ains the counters necessary for ge neration of the read and write address pointers. the embedded sram /fifo blocks can be cascaded to create larger configurations. pll and ccc military proasic3 devices provide designers wi th flexible clock cond itioning circuit (ccc) capabilities. each member of the military proasic3 family contai ns six cccs, located at the four corners and the centers of the east and west sides. one ccc (center west side) ha s a pll. all six ccc blocks are usable; the four corner cccs and the ea st ccc allow simple clock delay operations as well as clock spine access. military proasic3el devices also contain six cccs; however, a ll six are equipped with a pll. www..net
military proasic3/el de vice family overview v1.0 1-7 the inputs of the six ccc blocks are accessible from the fpga core or fro m one of several inputs located near the ccc that have dedicated connections to the ccc block. the ccc block has these key features: ? wide input frequency range (f in_ccc ) = 1.5 mhz up to 250 mhz ? output frequency range (f out_ccc ) = 0.75 mhz up to 250 mhz ? 2 programmable delay types for clock skew minimization ? clock frequency synthesis additional ccc specifications: ? internal phase shift = 0, 90, 180, and 270 . output phase shift depends on the output divider configuration. ? output duty cycle = 50 % 1.5 % or better ? low output jitter: worst case < 2.5 % clock period peak-to-peak period jitter when single global network used ? maximum acquisition time is 300 s ? exceptional tolerance to input period jitter ?allowable input jitter is up to 1.5 ns ? four precise phases; maximum misalignment be tween adjacent phases of 40 ps 250 mhz / f out_ccc global clocking military proasic3/el devices have extensive suppor t for multiple clocking domains. in addition to the ccc and pll support describe d above, there is a comprehe nsive global cl ock distribution network. each versatile input and output port has access to nine versanets: six chip (main) and three quadrant global networks. the ve rsanets can be driven by the ccc or directly accessed from the core via multiplexers (muxes). the versanets can be used to distribute low-s kew clock signals or for rapid distribution of high-fanout nets. i/os with advanced i/o standards the military proasic3/el family of fpgas features a flexible i/o structure, supporting a range of voltages (1.5 v, 1.8 v, 2.5 v, and 3.3 v). in addition, 1.2 v i/o op eration is supported for military proasic3el devices. military pr oasic3/el fpgas support different i/o standards, including single- ended, differential, and voltage- referenced (military proasic3el ). the i/os are organized into banks, with two, four, or eight (military proasic3el only) banks per device. the configuration of these banks determines the i/o standards suppo rted. for military proasic3el, each i/o bank is subdivided into v ref minibanks, which are used by voltage-referenced i/os. v ref minibanks contain 8 to 18 i/os. all the i/os in a given minibank share a common v ref line. therefore, if any i/o in a given v ref minibank is configured as a v ref pin, the remaining i/os in that minibank will be able to use that reference voltage. each i/o module contains several input, output , and enable registers. these registers allow the implementation of the following: ? single-data-rate applications (e.g., pci 66 mhz, bidirectional sstl 2 and 3, class i and ii) ? double-data-rate applications (e.g., ddr lvds, b-lvds, and m-lvds i/os for point-to-point communications, and ddr 200 mhz sram using bidirectional hstl class ii). military proasic3el banks support lvpecl, lvds, b-lvds, and m-lvds. b-lvds and m-lvds can support up to 20 loads. part number and revision date part number 51700106-001-0 revised august 2008 www..net
military proasic3/el device family overview 1-8 v1.0 datasheet categories categories in order to provide the latest information to desi gners, some datasheets are published before data has been fully characterized. datasheets are designated as "product brief," "advance," "preliminary," and "production." the definiti on of these categories are as follows: product brief the product brief is a summarized version of a datasheet (advance or production) and contains general product information. this document give s an overview of specific device and family information. advance this version contains initial estimated information based on simulation, ot her products, devices, or speed grades. this information can be used as estimates, but not for production. this label only applies to the dc and switching characteristics chapte r of the datasheet and will only be used when the data has not been fully characterized. preliminary the datasheet contains information based on si mulation and/or initia l characterization. the information is believed to be co rrect, but changes are possible. unmarked (production) this version contains information that is considered to be final. export administration regulations (ear) the products described in this do cument are subject to the expo rt administration regulations (ear). they could require an ap proved export license prior to export from the united states. an export includes release of product or disclosure of technology to a foreign national inside or outside the united states. actel safety critical, life support, and high-reliability applications policy the actel products described in this advance status document may not have completed actel?s qualification process. actel may amend or enhance products during the product introduction and qualification process, resulting in changes in device functional ity or performance. it is the responsibility of each customer to ensure the fitn ess of any actel product (but especially a new product) for a particular purpose, including appr opriateness for safety-cri tical, life-s upport, and other high-reliability applicatio ns. consult actel?s terms and cond itions for specific liability exclusions relating to life-support applications. a reliabilit y report covering all of actel?s products is available on the actel website at http://www.actel.com/documents/ort_report.pdf . actel also offers a variety of enhanced qualification and lot acceptance screening procedures. contact your local actel sales office for addi tional reliability information. www..net
v1.0 2-1 2 ? military proasic3/el dc and switching characteristics general specifications operating conditions stresses beyond those listed in table 2-1 may cause permanent damage to the device. exposure to absolute maximum rati ng conditions for extended period s may affect device reliability. absolute maximum ratings are stress ratings only; functional operation of the device at these or any other conditions beyond those listed unde r the recommended operat ing conditions specified in table 2-2 on page 2-2 is not implied. table 2-1 ? absolute maxi mum ratings symbol parameter limits units v cc dc core supply voltage ?0.3 to 1.65 v v jtag jtag dc voltage ?0.3 to 3.75 v v pump programming voltage ?0.3 to 3.75 v v ccpll analog power supply (pll) ?0.3 to 1.65 v v cci dc i/o output buffer supply voltage for a3pe600l and a3pe3000l. dc output buffer supply voltage for A3P1000. ?0.3 to 3.75 v vi i/o input voltage ?0.3 v to 3.6 v (when i/o hot insertion mode is enabled) ?0.3 v to ( v cci + 1 v) or 3.6 v, whichever voltage is lower (when i/o hot-insertion mode is disabled) v vmv dc input buffer supply voltage for A3P1000 ?0.3 to 3.75 v t stg 2 storage temperature ?65 to +150 c t j 2 junction temperature +150 c notes: 1. the device should be operated with in the limits specified by the data sheet. during transitions, the input signal may undershoot or overshoot according to the limits shown in table 2-4 on page 2-7 . 2. for flash programming and rete ntion maximum li mits, refer to table 2-3 on page 2-3 , and for recommended operatin g limits, refer to table 2-2 on page 2-2 . www..net
military proasic3/el low-power flash fpgas 2-2 v1.0 table 2-2 ? recommended operating conditions 2 symbol parameter military units t a ambient temperature ?55 to 125 c t j junction temper ature ?55 to 125 c v cc dc core supply voltage for a3pe600l/a3pe3000l 1.14 to 1.575 v dc core supply voltage for A3P1000 1 1.425 to 1.575 v v jtag jtag dc voltage 1.4 to 3.6 v v pump 3 programming voltage progr amming mode 3.15 to 3.45 v operation 3 0 to 3.6 v v ccpll analog power su pply (pll) for a3pe600l/a3pe3000l dc core supply vo ltage 1.14 to 1.575 v analog power su pply (pll) for A3P1000 dc core supply voltage 1.425 to 1.575 v cci and vmv 1.2 v dc supply voltage 4 1.14 to 1.26 v 1.5 v dc supply voltage 1.425 to 1.575 v 1.8 v dc supply voltage 1.7 to 1.9 v 2.5 v dc supply voltage 2.3 to 2.7 v 3.3 v dc supply voltage 3.0 to 3.6 v lvds differential i/o 2.375 to 2.625 v lvpecl differential i/o 3.0 to 3.6 v notes: 1. the ranges given here are for power supplies only. th e recommended input voltage ranges specific to each i/o standard are given in table 2-23 on page 2-24 . vmv and v cci should be at the sa me voltage within a given i/o bank. 2. all parameters representing voltages are measured with respect to gnd unless otherwise specified. 3. v pump can be left floating during normal operation (not programming mode). 4. for a3pe600l and a3pe3000l devices only. www..net
military proasic3/el low-power flash fpgas v1.0 2-3 note: htr time is the period during wh ich you would not expect a verify failure due to flash cell leakage. figure 2-1 ? high-temperature data retention (htr) table 2-3 ? overshoot and undershoot limits v cci and vmv average v cci ?gnd overshoot or undershoot duration as a percen tage of clock cycle maximum overshoot/ undershoot (125c) 2.7 v or less 10 % 0.72 v 5 % 0.82 v 3 v 10 % 0.72 v 5 % 0.81 v 3.3 v 10 % 0.69 v 5 % 0.79 v 3.6 v 10 % n/a 5 % n/a notes: 1. the duration is allowed at one out of six clock cycles. if the overshoot/ undershoot occurs at one out of two cycles, the maximum overshoot/undersho ot has to be reduced by 0.15 v. 2. this table does not provide pci overshoot/undershoot limits. 0 10 20 30 40 50 6 0 70 80 90 100 110 70 85 100 105 110 115 120 125 130 135 140 145 150 temperature (oc) year s tj ( c ) htr lifetime (yrs) 70 102.7 85 43.8 100 20.0 105 15. 6 110 12.3 115 9.7 120 7.7 125 6 .2 130 5.0 135 4.0 140 3.3 145 2.7 150 2.2 www..net
military proasic3/el low-power flash fpgas 2-4 v1.0 i/o power-up and supply voltage thresholds for power-on reset (military) sophisticated power-up management circ uitry is designed into every proasic ? 3 device. these circuits ensure eas y transition from the powered-off state to the powered-up state of the device. the many different supplies can power up in any se quence with minimized current spikes or surges. in addition, the i/o will be in a known state through the power-up sequence. the basic principle is shown in figure 2-2 on page 2-5 and figure 2-3 on page 2-6 . there are five regions to consider during power-up. military proasic3 i/os are activated only if all of the following three conditions are met: 1. v cc and v cci are above the minimum specified trip points ( figure 2-2 on page 2-5 and figure 2-3 on page 2-6 ). 2. v cci > v cc ? 0.75 v (typical) 3. chip is in the operating mode. v cci trip point: ramping up: 0.6 v < tr ip_point_up < 1.2 v ramping down: 0.5 v < trip_point_down < 1.1 v v cc trip point: ramping up: 0.6 v < tr ip_point_up < 1.1 v ramping down: 0.5 v < trip_point_down < 1 v v cc and v cci ramp-up trip points are about 100 mv hi gher than ramp-dow n trip points. this specifically built-in hysteresis pr events undesirable power-up oscillations and current surges. note the following: ? during programming, i/os become tri stated and weakly pulled up to v cci . ? jtag supply, pll power supplies, and charge pump v pump supply have no influence on i/o behavior. www..net
military proasic3/el low-power flash fpgas v1.0 2-5 pll behavior at br ownout condition actel recommends using monotonic power supplies or voltage regula tors to ensure proper power- up behavior. power ramp-up should be monotonic, at least until v cc and v ccplx exceed brownout activation levels. the v cc activation level is specifie d as 1.1 v worst-case (see figure 2-2 and figure 2-3 on page 2-6 for more details). when pll power supply voltage and/or v cc levels drop below the v cc brownout levels (0.75 v 0.25 v), the pll output lock signal goes low and/or the output clock is lost. refer to the power- up/-down behavior of low-power flash devices chapter of the handbook for information on clock and lock recovery. internal power-up activation sequence 1. core 2. input buffers output buffers, after 200 ns delay from input buffer activation. figure 2-2 ? devices operating at 1.5 v core ? i/o state as a function of v cci and v cc voltage levels region 1: i/o buffers are off region 2: i/o buffers are on. i/os are functional (except differential inputs) but slower because v cci /v cc are below specification. for the same reason, input buffers do not meet v ih /v il levels, and output buffers do not meet v oh /v ol levels. min v cci datasheet specification voltage at a selected i/o standard; i.e., 1.425 v or 1.7 v or 2.3 v or 3.0 v v cc v cc = 1.425 v region 1: i/o buffers are off activation trip point: v a = 0.85 v 0.25 v deactivation trip point: v d = 0.75 v 0.25 v activation trip point: v a = 0.9 v 0.3 v deactivation trip point: v d = 0.8 v 0.3 v v cc = 1.575 v region 5: i/o buffers are on and power supplies are within specification. i/os meet the entire datasheet and timer specifications for speed, v ih /v il , v oh /v ol , etc. region 4: i/o buffers are on. i/os are functional (except differential but slower because v cci is below specification. for the same reason, input buffers do not meet v ih /v il levels, and output buffers do not meet v oh /v ol levels. region 4: i/o buffers are on. i/os are functional (except differential inputs) where vt can be from 0.58 v to 0.9 v (typically 0.75 v) v cci region 3: i/o buffers are on. i/os are functional; i/o dc specifications are met, but i/os are slower because the v cc is below specification. v cc = v cci + vt www..net
military proasic3/el low-power flash fpgas 2-6 v1.0 figure 2-3 ? device operating at 1.2 v core voltage ? i/o state as a function of v cci and v cc voltage levels; only a3pe600l and a3pe3000l device s operate at 1.2 v core voltage region 1: i/o buffers are off region 2: i/o buffers are on. i/os are functional (except differential inputs) but slower because v cci /v cc are below specification. for the same reason, input buffers do not meet v ih /v il levels, and output buffers do not meet v oh /v ol levels. min v cci datasheet specification voltage at a selected i/o standard; i.e., 1.14 v,1.425 v, 1.7 v, 2.3 v, or 3.0 v v cc v cc = 1.14 v region 1: i/o buffers are off activation trip point: v a = 0.85 v 0.2 v deactivation trip point: v d = 0.75 v 0.2 v activation trip point: v a = 0.9 v 0.15 v deactivation trip point: v d = 0.8 v 0.15 v v cc = 1.575 v region 5: i/o buffers are on and power supplies are within specification. i/os meet the entire datasheet and timer specifications for speed, v ih /v il , v oh /v ol , etc. region 4: i/o buffers are on. i/os are functional (except differential but slower because v cci is below specification. for the same reason, input buffers do not meet v ih /v il levels, and output buffers do not meet v oh /v ol levels. region 4: i/o buffers are on. i/os are functional (except differential inputs) where vt can be from 0.58 v to 0.9 v (typically 0.75 v) v cci region 3: i/o buffers are on. i/os are functional; i/o dc specifications are met, but i/os are slower because the v cc is below specification. v cc = v cci + vt www..net
military proasic3/el low-power flash fpgas v1.0 2-7 thermal characteristics introduction the temperature variable in the actel designer software refers to the junction temperature, not the ambient temperature. this is an important distinction be cause dynamic and static power consumption cause the chip junction temperatur e to be higher than the ambient temperature. eq 2-1 can be used to calculate junction temperature. t j = junction temperature = t + t a eq 2-1 where: t a = ambient temperature t = temperature gradient between junction (silicon) and ambient t = ja * p ja = junction-to-ambient of the package. ja numbers are located in table 2-4 . p = power dissipation package thermal characteristics the device junction-to-case thermal resistivity is jc and the junction-to-ambient air thermal resistivity is ja . the thermal characteristics for ja are shown for two air flow rates. the recommended maximum junction temperature is 125c. eq 2-2 shows a sample ca lculation of the recommended maximum power dissipation allo wed for a 484-pin fbga package at military temperature and in still air. eq 2-2 maximum power allowed max. junction temp. ( c) max. ambient temp. ( c) ? ja ( c/w) ------------------------------------------------------------------------------------------------------------------------------- -------- 125 c70 c ? 20.6 c/w ------------------------------------ 2 . 6 7 0 = = = table 2-4 ? package thermal resistivities package type devi ce pin count jc ja units still air 200 ft./min. 500 ft./min. plastic quad flat pack (pq208)* A3P1000 208 3.8 16.2 13.3 11.9 c/w fine pitch ball grid array (fbga) A3P1000 144 6.3 31.6 26.2 24.2 c/w a3pe600l 484 9.5 27.5 21.9 20.2 c/w a3pe3000l 484 4.7 20.6 15.7 14.0 c/w a3pe3000l 896 2.4 13.6 10.4 9.4 c/w * embedded heatspreader www..net
military proasic3/el low-power flash fpgas 2-8 v1.0 temperature and voltage derating factors table 2-5 ? temperature and voltage derati ng factors for timing delays (normalized to t j = 125c, v cc = 1.14 v) applicable to a3pe 600l and a3pe3000l only junction temperature array voltage v cc (v) ?55c ?40c 0c 25c 70c 85c 125c 1.14 0.86 0.87 0.90 0.92 0.96 0.98 1.00 1.2 0.83 0.84 0.87 0.89 0.93 0.94 0.96 1.26 0.79 0.80 0.83 0.85 0.89 0.90 0.92 1.3 0.77 0.78 0.81 0.83 0.86 0.88 0.90 1.35 0.75 0.75 0.78 0.80 0.83 0.85 0.87 1.4 0.72 0.73 0.75 0.77 0.80 0.81 0.83 1.425 0.70 0.71 0.74 0.76 0.79 0.80 0.82 1.5 0.67 0.67 0.70 0.71 0.75 0.76 0.78 1.575 0.64 0.65 0.67 0.69 0.72 0.73 0.75 table 2-6 ? temperature and voltage derati ng factors for timing delays (normalized to t j = 125c, v cc = 1.425 v) applicable to a 3p1000 devices only junction temperature array voltage v cc (v) ?55c ?40c 0c 25c 70c 85c 125c 1.425 0.81 0.83 0.88 0.90 0.95 0.97 1.00 1.5 0.77 0.79 0.83 0.85 0.90 0.92 0.95 1.575 0.74 0.76 0.80 0.82 0.87 0.88 0.92 www..net
military proasic3/el low-power flash fpgas v1.0 2-9 calculating power dissipation quiescent supply current table 2-7 ? quiescent supply current (i dd ) characteristics when using fl ash*freeze mode in military proasic3/el* core voltage a3pe600l a3pe3000l units typical (25c) 1.2 v 2.75 ma 1.5 v ma * i dd includes v cc , v pump , v cci , v jtag , and v ccpll currents. values do not in clude i/o static contribution (p dc6 and p dc7 ). table 2-8 ? quiescent supply current (i dd ) characteristics, military proasic3/el sleep mode (v cc = 0 v)* core voltage a3p e600l a3p e3000l units v cci / v jtag = 1.2 v (per bank) ty p i c a l ( 2 5 c ) 1.2 v / 1.5 v 1.7 1.7 a v cci / v jtag = 1.5 v (per bank) ty p i c a l ( 2 5 c ) 1.2 v / 1.5 v 1.8 1.8 a v cci / v jtag = 1.8 v (per bank) ty p i c a l ( 2 5 c ) 1.2 v / 1.5 v 1.9 1.9 a v cci / v jtag = 2.5 v (per bank) ty p i c a l ( 2 5 c ) 1.2 v / 1.5 v 2.2 2.2 a v cci / v jtag = 3.3 v (per bank) ty p i c a l ( 2 5 c ) 1.2 v / 1.5 v 2.5 2.5 a * i dd includes v cc , v pump , and v ccpll currents. values do not in clude i/o static contribution (p dc6 and p dc7 ). table 2-9 ? quiescent supply current (i dd ) characteristics for a3pe600l and a3pe3000l devices only shutdown mode, (v cc and v cci = 0 v)* core voltage a3pe600l a3pe3000l typical (25c) 1.2 v 0 a * i dd includes v cc , v pump , v cci , v jtag , and v ccpll currents. values do not include i/o static contribution (p dc6 and p dc7 ). www..net
military proasic3/el low-power flash fpgas 2-10 v1.0 table 2-10 ? quiescent supply current (i dd ), no military proasic3/el flash*freeze mode 1 core voltage a3pe600l a3pe3000l units i cca current 2 typical (25c) 1.2 v 2.75 ma 1.5 v ma i cci or i jtag current 3, 4 v cci / v jtag = 1.2 v (per bank) typical (25c) 1.2 v / 1.5 v 1.7 1.7 a v cci / v jtag = 1.5 v (per bank) typical (25c) 1.2 v / 1.5 v 1.8 1.8 a v cci / v jtag = 1.8 v (per bank) typical (25c) 1.2 v / 1.5 v 1.9 1.9 a v cci / v jtag = 2.5 v (per bank) typical (25c) 1.2 v / 1.5 v 2.2 2.2 a v cci / v jtag = 3.3 v (per bank) typical (25c) 1.2 v / 1.5 v 2.5 2.5 a notes: 1. to calculate total device i dd , multiply the number of banks used by i cci and add i cca contribution. 2. includes v cc , v ccpll , and v pump currents. 3. per v cci or v jtag bank. 4. values do not include i/o static contribution (p dc6 and p dc7 ). table 2-11 ? quiescent supply current (i dd ) characteristics A3P1000 typical (25c) 8 ma maximum military (125c) 200 ma * i dd includes v cc , v pump , v cci , v jtag , and v ccpll currents. values do not include i/o static contribution (p dc6 and p dc7 ). www..net
military proasic3/el low-power flash fpgas v1.0 2-11 power per i/o pin table 2-12 ? summary of i/o input buffer power (per pin) ? default i/o software settings applicable to pro i/os fo r a3pe600l and a3pe3000l only v cci (v) static power p dc6 (mw) 1 dynamic power p ac9 (w/mhz) 2 single-ended 3.3 v lvttl/lvcmos 3.3 ? 16.34 3.3 v lvttl/lvcmos ? schmitt trigger 3.3 ? 24.49 2.5 v lvcmos 2.5 ? 4.71 2.5 v lvcmos ? schmitt trigger 2.5 ? 6.13 1.8 v lvcmos 1.8 ? 1.66 1.8 v lvcmos ? schmitt trigger 1.8 ? 1.78 1.5 v lvcmos (jesd8-11) 1.5 ? 1.01 1.5 v lvcmos (jesd8-11) ? schmitt trigger 1.5 ? 0.97 1.2 v lvcmos 3 1.2 ? 0.60 1.2 v lvcmos (jesd8-11) ? schmitt trigger 3 1.2 ? 0.53 3.3 v pci 3.3 ? 17.76 3.3 v pci ? schmitt trigger 3.3 ? 19.10 3.3 v pci-x 3.3 ? 17.76 3.3 v pci-x ? schmitt trigger 3.3 ? 19.10 voltage-referenced 3.3 v gtl 3.3 2.90 7.07 2.5 v gtl 2.5 2.13 3.62 3.3 v gtl+ 3.3 2.81 2.97 2.5 v gtl+ 2.5 2.57 2.55 hstl (i) 1.5 0.17 0.85 hstl (ii) 1.5 0.17 0.85 sstl2 (i) 2.5 1.38 3.30 sstl2 (ii) 2.5 1.38 3.30 sstl3 (i) 3.3 3.21 8.08 sstl3 (ii) 3.3 3.21 8.08 differential lvds 2.5 2.26 0.95 lvpecl 3.3 5.71 1.62 notes: 1. p dc6 is the static power (where applicable) measured on v cci . 2. p ac9 is the total dynamic power measured on v cci . www..net
military proasic3/el low-power flash fpgas 2-12 v1.0 table 2-13 ? summary of i/o input buffer power (per pin) ? default i/o software settings 1 applicable to advanced i/o banks for A3P1000 only vmv (v) static power p dc6 (mw) 2 dynamic power p ac9 (w/mhz) 3 single-ended 3.3 v lvttl / 3.3 v lvcmos 3.3 ? 16.69 2.5 v lvcmos 2.5 ? 5.12 1.8 v lvcmos 1.8 ? 2.13 1.5 v lvcmos (jesd8-11) 1.5 ? 1.45 3.3 v pci 3.3 ? 18.11 3.3 v pci-x 3.3 ? 18.11 differential lvds 2.5 2.26 1.20 lvpecl 3.3 5.72 1.87 notes: 1. p dc6 is the static power (where applicable) measured on vmv. 2. p ac9 is the total dynamic power measured on vmv. table 2-14 ? summary of i/o input buffer power (per pin) ? default i/o software settings applicable to standard pl us i/o banks for A3P1000 only vmv (v) static power p dc6 (mw) 1 dynamic power p ac9 (w/mhz) 2 single-ended 3.3 v lvttl / 3.3 v lvcmos 3.3 ? 16.72 2.5 v lvcmos 2.5 ? 5.14 1.8 v lvcmos 1.8 ? 2.13 1.5 v lvcmos (jesd8-11) 1.5 ? 1.48 1.2 v lvcmos 3.3 ? 18.13 3.3 v pci 3.3 ? 18.13 3.3 v pci-x 3.3 ? 16.72 notes: 1. p dc6 is the static power (where applicable) measured on vmv. 2. p ac9 is the total dynamic power measured on vmv. www..net
military proasic3/el low-power flash fpgas v1.0 2-13 table 2-15 ? summary of i/o output buffer power (p er pin) ? default i/o software settings 1 applicable to pro i/os fo r a3pe600l and a3pe3000l only c load (pf) v cci (v) static power p dc7 (mw) 2 dynamic power p ac10 (w/mhz) 3 single-ended 3.3 v lvttl/lvcmos 5 3.3 ? 148.00 2.5 v lvcmos 5 2.5 ? 83.23 1.8 v lvcmos 5 1.8 ? 54.58 1.5 v lvcmos (jesd8-11) 5 1.5 ? 37.05 1.2 v lvcmos 4 5 1.2 ? 17.94 3.3 v pci 10 3.3 ? 204.61 3.3 v pci-x 10 3.3 ? 204.61 voltage-referenced 3.3 v gtl 10 3.3 ? 24.08 2.5 v gtl 10 2.5 ? 13.52 3.3 v gtl+ 10 3.3 ? 24.10 2.5 v gtl+ 10 2.5 ? 13.54 hstl (i) 20 1.5 7.08 26.22 hstl (ii) 20 1.5 13.88 27.22 sstl2 (i) 30 2.5 16.69 105.56 sstl2 (ii) 30 2.5 25.91 116.60 sstl3 (i) 30 3.3 26.02 114.87 sstl3 (ii) 30 3.3 42.21 131.76 differential lvds ? 2.5 7.70 89.62 lvpecl ? 3.3 19.42 168.02 notes: 1. dynamic power consumption is given for standard lo ad and software default dr ive strength and output slew. 2. p dc7 is the static power (where applicable) measured on v cci . 3. p ac10 is the total dynamic power measured on v cci . www..net
military proasic3/el low-power flash fpgas 2-14 v1.0 table 2-16 ? summary of i/o output buffer power (p er pin) ? default i/o software settings 1 applicable to advanced i/o banks for A3P1000 only c load (pf) v cci (v) static power p dc7 (mw) 2 dynamic power p ac10 (w/mhz) 3 single-ended 3.3 v lvttl / 3.3 v lvcmos 5 3.3 ? 141.97 2.5 v lvcmos 5 2.5 ? 79.98 1.8 v lvcmos 5 1.8 ? 52.26 1.5 v lvcmos (jesd8-11) 5 1.5 ? 35.62 3.3 v pci 10 3.3 ? 201.02 3.3 v pci-x 10 3.3 ? 201.02 differential lvds ? 2.5 7.74 89.71 lvpecl ? 3.3 19.54 167.54 notes: 1. dynamic power consumption is given for standard load and software default drive strength and output slew. 2. p dc7 is the static power (where applicable) measured on v cci . 3. p ac10 is the total dynamic power measured on v cci . table 2-17 ? summary of i/o output buffer power (p er pin) ? default i/o software settings applicable to standard pl us i/o banks for A3P1000 only c load (pf) v cci (v) static power p dc7 (mw) 2 dynamic power p ac10 (w/mhz) 3 single-ended 3.3 v lvttl / 3.3 v lvcmos 5 3.3 ? 125.97 2.5 v lvcmos 5 2.5 ? 70.82 1.8 v lvcmos 5 1.8 ? 36.39 1.5 v lvcmos (jesd8-11) 5 1.5 ? 25.34 3.3 v pci 10 3.3 ? 184.92 3.3 v pci-x 10 3.3 ? 184.92 notes: 1. dynamic power consumption is given for standard load and software default drive strength and output slew. 2. p dc7 is the static power (where applicable) measured on v cci . 3. p ac10 is the total dynamic power measured on v cci . www..net
military proasic3/el low-power flash fpgas v1.0 2-15 power consumption of vari ous internal resources table 2-18 ? different components contributing to dynamic power consumption in devices operating at 1.2 v v cc parameter definition device-specific dynamic power (w/mhz) a3pe3000l a3pe600l p ac1 clock contribution of a global rib 12.61 p ac2 clock contribution of a global spine 2.66 p ac3 clock contribution of a versatile row 0.56 p ac4 clock contribution of a versa tile used as a sequential module 0.07 p ac5 first contribution of a versatile used as a sequential module 0.05 p ac6 second contribution of a ve rsatile used as a sequential module 0.19 p ac7 contribution of a versatile used as a combinatorial module 0.11 p ac8 average contribution of a routing net 0.45 p ac9 contribution of an i/o input pin (standard-dependent) see table 2-12 on page 2-11 through table 2-14 on page 2-12 . p ac10 contribution of an i/o output pin (standard-dependent) see table 2-15 on page 2-13 through table 2-17 on page 2-14 . p ac11 average contribution of a ram block during a read operation 25.00 p ac12 average contribution of a ram block during a write operation 30.00 p ac13 dynamic contribution for pll 1.74 www..net
military proasic3/el low-power flash fpgas 2-16 v1.0 table 2-19 ? different components contributing to dynamic power consumption in military proasic3/el devices at 1.5 v v cc parameter definition device-specific dynamic power (w/mhz) a3pe3000l a3pe600l A3P1000 p ac1 clock contribution of a global rib 19.7 14.50 p ac2 clock contribution of a global spine 4.16 2.48 p ac3 clock contribution of a versatile row 0.88 0.81 p ac4 clock contribution of a vers atile used as a sequential module 0.12 p ac5 first contribution of a vers atile used as a sequential module 0.07 p ac6 second contribution of a versatile used as a sequential module 0.29 p ac7 contribution of a versatile used as a combinatorial module 0.29 p ac8 average contribution of a routing net 0.70 p ac9 contribution of an i/o input pin (standard-dependent) see table 2-12 on page 2-11 through table 2-14 on page 2-12 . p ac10 contribution of an i/o output pin (standard- dependent) see table 2-15 on page 2-13 through table 2-17 on page 2-14 . p ac11 average contribution of a ram block during a read operation 25.00 p ac12 average contribution of a ram block during a write operation 30.00 p ac13 dynamic contribution for pll 2.60 table 2-20 ? different components contributing to the static power consumption in military proasic3/el devices parameter definition device-specific dynamic power (w) a3pe3000l a3pe600l A3P1000 p dc1 array static power in active mode see table 2-10 on page 2-10 . p dc2 array static power in static (idle) mode see table 2-10 on page 2-10 . p dc3 array static power in flash*freeze mode see table 2-7 on page 2-9 . p dc4 static pll contribution at 1.2 v operating core voltage (for a3pe600l and a3pe3000l only) 1.42 mw n/a static pll contributi on 1.5 v operating core voltage 2.55 mw p dc5 bank quiescent power (v cci -dependent) see table 2-7 on page 2-9 , table 2-8 on page 2-9 , table 2-10 on page 2-10 . p dc6 i/o input pin static power (standard-dependent) see table 2-12 on page 2-11 . through table 2-14 on page 2-12 . p dc7 i/o output pin static power (standard-dependent) see table 2-15 on page 2-13 through table 2-17 on page 2-14 . * for a different output load, drive strength, or slew rate, actel recommends using the actel power spreadsheet calculator or smartp ower tool in libero ? integrated design environment (ide). www..net
military proasic3/el low-power flash fpgas v1.0 2-17 power calculation methodology this section describes a simplified method to estimate power consumptio n of an application. for more accurate and deta iled power estima tions, use the smartpower tool in actel libero ide software. the power calculation methodology described below uses the following variables: ? the number of plls as well as the number and the frequency of each output clock generated ? the number of combinatorial and se quential cells used in the design ?the internal clock frequencies ? the number and the standard of i/o pins used in the design ? the number of ram blocks used in the design ? toggle rates of i/o pins as well as versatiles?guidelines are provided in table 2-21 on page 2-19 . ? enable rates of output buffers?guidelines are provided for typical applications in table 2-22 on page 2-19 . ? read rate and write rate to the memory?guide lines are provided for typical applications in table 2-22 on page 2-19 . the calculation should be repeat ed for each clock domain defined in the design. methodology total power consumption?p total p total = p stat + p dyn p stat is the total static power consumption. p dyn is the total dynamic power consumption. total static power consumption?p stat p stat = (p dc1 or p dc2 or p dc3 ) + n banks * p dc5 + n inputs * p dc6 + n outputs * p dc7 n inputs is the number of i/o input buffers used in the design. n outputs is the number of i/o output buffers used in the design. n banks is the number of i/o bank s powered in the design. total dynamic power consumption?p dyn p dyn = p clock + p s-cell + p c-cell + p net + p inputs + p outputs + p memory + p pll global clock contribution?p clock p clock = (p ac1 + n spine *p ac2 + n row *p ac3 + n s-cell * p ac4 ) * f clk n spine is the number of global spines used in the user design?guidelines are provided in table 2-21 on page 2-19 . n row is the number of versatile rows used in the design?guidelines are provided in table 2-21 on page 2-19 . f clk is the global clock signal frequency. n s-cell is the number of versatiles used as sequential modules in the design. p ac1 , p ac2 , p ac3 , and p ac4 are device-dependent. sequential cells contribution?p s-cell p s-cell = n s-cell * (p ac5 + 1 / 2 * p ac6 ) * f clk n s-cell is the number of versatiles used as se quential modules in the design. when a multi-tile sequential cell is used, it should be accounted for as 1. 1 is the toggle rate of versatile outputs?guidelines are provided in table 2-21 on page 2-19 . f clk is the global clock signal frequency. www..net
military proasic3/el low-power flash fpgas 2-18 v1.0 combinatorial cells contribution?p c-cell p c-cell = n c-cell * 1 / 2 * p ac7 * f clk n c-cell is the number of versatiles used as combinatorial modu les in the design. 1 is the toggle rate of versatile outputs?guidelines are provided in table 2-21 on page 2-19 . f clk is the global clock signal frequency. routing net contribution?p net p net = (n s-cell + n c-cell ) * 1 / 2 * p ac8 * f clk n s-cell is the number of versatiles used as sequential modules in the design. n c-cell is the number of versatiles used as combinatorial modu les in the design. 1 is the toggle rate of versatile outputs?guidelines are provided in table 2-21 on page 2-19 . f clk is the global clock signal frequency. i/o input buffer contribution?p inputs p inputs = n inputs * 2 / 2 * p ac9 * f clk n inputs is the number of i/o input buffers used in the design. 2 is the i/o buffer toggle rate?guidelines are provided in table 2-21 on page 2-19 . f clk is the global clock signal frequency. i/o output buffer contribution?p outputs p outputs = n outputs * 2 / 2 * 1 * p ac10 * f clk n outputs is the number of i/o output buffers used in the design. 2 is the i/o buffer toggle rate?guidelines are provided in table 2-21 on page 2-19 . 1 is the i/o buffer enable rate ?guidelines are provided in table 2-22 on page 2-19 . f clk is the global clock signal frequency. ram contribution?p memory p memory = p ac11 * n blocks * f read-clock * 2 + p ac12 * n block * f write-clock * 3 n blocks is the number of ram blocks used in the design. f read-clock is the memory read clock frequency. 2 is the ram enable rate for read operations. f write-clock is the memory write clock frequency. 3 is the ram enable rate for write op erations?guidelines are provided in table 2-22 on page 2-19 . pll contribution?p pll p pll = p dc4 + p ac13 *f clkout f clkout is the output clock frequency. 1 1. if a pll is used to generate more than one output clock, include each output clock in the formula by adding its corresponding contribution (p ac13 * f clkout product) to the total pll contribution. www..net
military proasic3/el low-power flash fpgas v1.0 2-19 guidelines toggle rate definition a toggle rate defines the frequency of a net or logi c element relative to a clock. it is a percentage. if the toggle rate of a net is 100 % , this means that this net switch es at half the clock frequency. below are some examples: ? the average toggle rate of a shift register is 100 % because all flip-flop outputs toggle at half of the clock frequency. ? the average toggle rate of an 8-bit counter is 25 % : ? bit 0 (lsb) = 100 % ? bit 1 = 50 % ? bit 2 = 25 % ?? ? bit 7 (msb) = 0.78125 % ? average toggle rate = (100 % + 50 % + 25 % + 12.5 % + . . . + 0.78125 % ) / 8 enable rate definition output enable rate is the average percentage of time during which tris tate outputs are enabled. when nontristate output buffers are us ed, the enable rate should be 100 % . table 2-21 ? toggle rate guidelines reco mmended for power calculation component definition guideline 1 toggle rate of versatile outputs 10 % 2 i/o buffer toggle rate 10 % table 2-22 ? enable rate guidelines reco mmended for power calculation component definition guideline 1 i/o output buffer enable rate 100 % 2 ram enable rate for read operations 12.5 % 3 ram enable rate for write operations 12.5 % www..net
military proasic3/el low-power flash fpgas 2-20 v1.0 user i/o characteristics timing model figure 2-4 ? timing model operating conditions: ?1 speed, military temperature range (t j = 125c), worst-case v cc = 1.14 v (example for a3pe3000l and a3pe600l) dq y y dq dq dq y combinational cell combinational cell combinational cell i/o module (registered) i/o module (non-registered) register cell register cell i/o module (registered) i/o module (non-registered) lvpecl lvpecl lvds, b-lvds, m-lvds lvttl 3.3 v output drive strength = 12 ma high slew rate y combinational cell y combinational cell y combinational cell i/o module (non-registered) lvttl output drive strength = 8 ma high slew rate i/o module (non-registered) lvcmos 1.5 v output drive strength = 4 ma high slew rate lvttl output drive strength = 12 ma high slew rate i/o module (non-registered) input lvttl clock input lvttl clock input lvttl clock t pd = 0.78 ns t pd = 0.67 ns t dp = 1.54 ns t pd = 1.21 ns t dp = 2.08 ns t pd = 0.70 ns t dp = 2.37 ns t pd = 0.65 ns t dp = 2.83 ns t pd = 0.65 ns t py = 1.48 ns t clkq = 0.76 ns t oclkq = 0.81 ns t sud = 0.9 ns t osud = 0.43 ns t dp = 2.08 ns t py = 1.48 ns t py = 2.04 ns t clkq = 0.76 ns t sud = 0.59 ns t py = 1.48 ns t iclkq = 0.33 ns t isud = 0.36 ns t py = 1.84 ns www..net
military proasic3/el low-power flash fpgas v1.0 2-21 figure 2-5 ? input buffer timing model and delays (example) t py (r) pad y v trip gnd t py (f) v trip 50 % 50 % v ih v cc v il t dout (r) din gnd t dout (f) 50 % 50 % v cc pad y t py d clk q i/o interface din t din to array t py = max(t py (r), t py (f)) t din = max(t din (r), t din (f)) www..net
military proasic3/el low-power flash fpgas 2-22 v1.0 figure 2-6 ? output buffer model and delays (example) t dp (r) pad v ol t dp (f) v trip v trip v oh v cc d 50 % 50 % v cc 0 v dout 50 % 50 % 0 v t dout (r) t dout (f) from array pad t dp std load d clk q i/o interface dout d t dout t dp = max(t dp (r), t dp (f)) t dout = max(t dout (r), t dout (f)) www..net
military proasic3/el low-power flash fpgas v1.0 2-23 figure 2-7 ? tristate output buffer timing model and delays (example) d clk q d clk q 10 % v cci t zl v trip 50 % t hz 90 % v cci t zh v trip 50 % 50 % t lz 50 % eout pad d e 50 % t eout (r) 50 % t eout (f) pad dout eout d i/o interface e t eout t zls v trip 50 % t zhs v trip 50 % eout pad d e 50 % 50 % t eout (r) t eout (f) 50 % v cc v cc v cc v cci v cc v cc v cc v oh v ol v ol t zl , t zh , t hz , t lz , t zls , t zhs t eout = max(t eout (r), t eout (f)) www..net
military proasic3/el low-power flash fpgas 2-24 v1.0 overview of i/o performance summary of i/o dc input and output levels ? default i/o software settings table 2-23 ? summary of maximum and minimu m dc input and output levels applicable to military conditions?so ftware default settings applicable to pro i/os fo r a3pe600l and a3pe3000l only i/o standard drive strength slew rate v il v ih v ol v oh i ol 1 i oh 1 min, v max, v min, v max, v max, v min, v ma ma 3.3 v lvttl / 3.3 v lvcmos 12 ma high ?0.3 0.8 2 3.6 0.4 2.4 12 12 2.5 v lvcmos 12 ma high ?0.3 0.7 1.7 2.7 0.7 1.7 12 12 1.8 v lvcmos 12 ma high ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 12 12 1.5 v lvcmos 12 ma high ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 12 12 1.2 v lvcmos 2 ma high ?0.3 0.35 * v cci 0.65 * v cci 1.26 0.25 * v cci 0.75 * v cci 22 3.3 v pci per pci specification 3.3 v pci-x per pci-x specification 3.3 v gtl 25 ma 2 high ?0.3 v ref ? 0.05 v ref + 0.05 3.6 0.4 ? 25 25 2.5 v gtl 25 ma 2 high ?0.3 v ref ? 0.05 v ref + 0.05 2.7 0.4 ? 25 25 3.3 v gtl+ 35 ma high ?0.3 v ref ? 0.1 v ref + 0.1 3.6 0.6 ? 51 51 2.5 v gtl+ 33 ma high ?0.3 v ref ? 0.1 v ref + 0.1 2.7 0.6 ? 40 40 hstl (i) 8 ma high ?0.3 v ref ? 0.1 v ref + 0.1 1.575 0.4 v cci ? 0.4 8 8 hstl (ii) 15 ma 2 high ?0.3 v ref ? 0.1 v ref + 0.1 1.575 0.4 v cci ? 0.4 15 15 sstl2 (i) 15 ma high ?0.3 v ref ? 0.2 v ref + 0.2 2.7 0.54 v cci ? 0.62 15 15 sstl2 (ii) 18 ma high ?0.3 v ref ? 0.2 v ref + 0.2 2.7 0.35 v cci ? 0.43 18 18 sstl3 (i) 14 ma high ?0.3 v ref ? 0.2 v ref + 0.2 3.6 0.7 v cci ? 1.1 14 14 sstl3 (ii) 21 ma high ?0.3 v ref ? 0.2 v ref + 0.2 3.6 0.5 v cci ? 0.9 21 21 notes: 1. currents are measured at 125c junction temperature. 2. output drive strength is below jedec specification. 3. output slew rate can be ex tracted using the ibis models. www..net
military proasic3/el low-power flash fpgas v1.0 2-25 table 2-24 ? summary of maximum and minimum dc input and output levels applicable to military conditions?software default settings applicable to advanced i/o banks for A3P1000 only i/o standard drive strength slew rate v il v ih v ol v oh i ol 1 i oh 1 min, v max, v min, v max, v max, v min, v ma ma 3.3 v lvttl / 3.3 v lvcmos 12 ma high ?0.3 0.8 2 3.6 0.4 2.4 12 12 2.5 v lvcmos 12 ma high ?0.3 0. 7 1.7 2.7 0.7 1.7 12 12 1.8 v lvcmos 12 ma high ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 12 12 1.5 v lvcmos 12 ma high ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 12 12 1.2 v lvcmos 2 ma high ?0.3 0.35 * v cci 0.65 * v cci 1.26 0.25 * v cci 0.75 * v cci 22 3.3 v pci per pci specifications 3.3 v pci-x per pci-x specifications notes: 1. currents are measured at 125c junction temperature. 2. output slew rate can be ex tracted using the ibis models table 2-25 ? summary of maximum and minimum dc input and output levels applicable to military conditions?software default settings applicable to standard pl us i/o banks for A3P1000 only i/o standard drive strength slew rate v il v ih v ol v oh i ol 1 i oh 1 min, v max, v min, v max, v max, v min, v ma ma 3.3 v lvttl / 3.3 v lvcmos 12 ma high ?0.3 0.8 2 3.6 0.4 2.4 12 12 2.5 v lvcmos 12 ma high ?0.3 0.7 1.7 2.7 0.7 1.7 12 12 1.8 v lvcmos 8 ma high ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 8 8 1.5 v lvcmos 4 ma high ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 4 4 1.2 v lvcmos 2 ma high ?0.3 0.35 * v cci 0.65 * v cci 1.26 0.25 * v cci 0.75 * v cci 22 3.3 v pci per pci specifications 3.3 v pci-x per pci-x specifications notes: 1. currents are measured at 125c junction temperature. 2. output slew rate can be ex tracted using the ibis models. www..net
military proasic3/el low-power flash fpgas 2-26 v1.0 table 2-26 ? summary of maximum and mi nimum dc input levels applicable to military conditions dc i/o standard military i il i ih a a 3.3 v lvttl / 3.3 v lvcmos 15 15 2.5 v lvcmos 15 15 1.8 v lvcmos 15 15 1.5 v lvcmos 15 15 1.2 v lvcmos 15 15 3.3 v pci 15 15 3.3 v pci-x 15 15 3.3 v gtl 15 15 2.5 v gtl 15 15 3.3 v gtl+ 15 15 2.5 v gtl+ 15 15 hstl (i) 15 15 hstl (ii) 15 15 sstl2 (i) 15 15 sstl2 (ii) 15 15 sstl3 (i) 15 15 sstl3 (ii) 15 15 note: military temperature range: ?55c to 125c www..net
military proasic3/el low-power flash fpgas v1.0 2-27 summary of i/o timing characteristics ? defaul t i/o software settings table 2-27 ? summary of ac memory points * standard input reference voltage (v ref_typ ) board termination voltage (v tt_ref ) measuring trip point (v trip ) 3.3 v lvttl / 3.3 v lvcmos ? ? 1.4 v 2.5 v lvcmos ? ? 1.2 v 1.8 v lvcmos ? ? 0.90 v 1.5 v lvcmos ? ? 0.75 v 1.2 v lvcmos* ? ? 0.6v 3.3 v pci ? ? 0.285 * v cci (rr) 0.615 * v cci (ff)) 3.3 v pci-x ? ? 0.285 * v cci (rr) 0.615 * v cci (ff) 3.3 v gtl 0.8 v 1.2 v v ref 2.5 v gtl 0.8 v 1.2 v v ref 3.3 v gtl+ 1.0 v 1.5 v v ref 2.5 v gtl+ 1.0 v 1.5 v v ref hstl (i) 0.75 v 0.75 v v ref hstl (ii) 0.75 v 0.75 v v ref sstl2 (i) 1.25 v 1.25 v v ref sstl2 (ii) 1.25 v 1.25 v v ref sstl3 (i) 1.5 v 1.485 v v ref sstl3 (ii) 1.5 v 1.485 v v ref lvds ? ? cross point lvpecl ? ? cross point * applicable to a3pe600l and a3pe3000l devices operating at 1.2 v core regions only. table 2-28 ? i/o ac paramete r definitions parameter parameter definition t dp data to pad delay through the output buffer t py pad to data delay thr ough the input buffer t dout data to output buffer de lay through th e i/o interface t eout enable to output buffer tristate con trol delay through the i/o interface t din input buffer to data delay through the i/o interface t hz enable to pad delay through the output buffer?high to z t zh enable to pad delay through the output buffer?z to high t lz enable to pad delay through the output buffer?low to z t zl enable to pad delay through the output buffer?z to low t zhs enable to pad delay through the output buffer with delayed enable?z to high t zls enable to pad delay through the output buffer with delayed enable?z to low www..net
military proasic3/el low-power flash fpgas 2-28 v1.0 1.2 v core operating voltage table 2-29 ? summary of i/o timing character istics?software default settings ?1 speed grade, military-case conditions: t j = 125c, worst case v cc = 1.14 v, worst case v cci applicable to pro i/os fo r a3pe600l and a3pe3000l only standard drive strength (ma) slew rate capacitive load (pf) external resistor ( ) t dout (ns) t dp (ns) t din (ns) t py (ns) t pys (ns) t eout (ns) t zl (ns) t zh (ns) t lz (ns) t hz (ns) t zls (ns) t zhs (ns) units 3.3 v lvttl / 3.3 v lvcmos 12 ma high 5 ? 0.68 2.08 0.05 1.48 2.03 0.44 2.12 1.56 2.76 3.04 4.00 3.44 ns 2.5 v lvcmos 12 ma high 5 ? 0.68 2.12 0.05 1. 74 2.16 0.44 2.16 1.74 2.84 2.94 4.04 3.63 ns 1.8 v lvcmos 12 ma high 5 ? 0.68 2.36 0.05 1. 69 2.38 0.44 2.40 1.94 3.14 3.57 4.28 3.82 ns 1.5 v lvcmos 12 ma high 5 ? 0.68 2.71 0.05 1. 86 2.59 0.44 2.76 2.24 3.34 3.68 4.64 4.12 ns 1.2 v lvcmos 2ma high 5 ? 0.684.400.052.233.200.444.213.714.354.116.025.52 ns 3.3 v pci per pci spec high 10 25 0.68 2.36 0.05 2.31 3.12 0. 44 2.41 1.68 2.76 3.04 4.29 3.56 ns 3.3 v pci-x per pci-x spec high 10 25 0.68 2.36 0.05 2.31 3.12 0. 44 2.41 1.68 2.76 3.04 4.29 3.56 ns 3.3 v gtl 25 ma high 10 25 0.68 1.75 0.05 1.98 ? 0.44 1.72 1.75 ? ? 3.60 3.63 ns 2.5 v gtl 25 ma high 10 25 0.68 1.79 0.05 1.92 ? 0.44 1.82 1.79 ? ? 3.70 3.68 ns 3.3 v gtl+ 35 ma high 10 25 0.68 1.73 0.05 1.98 ? 0.44 1.76 1.73 ? ? 3.65 3.61 ns 2.5 v gtl+ 33 ma high 10 25 0.68 1.86 0.05 1.92 ? 0.44 1.89 1.77 ? ? 3.78 3.65 ns hstl (i) 8 ma high 20 25 0.68 2.68 0.05 2.34 ? 0.44 2.73 2.65 ? ? 4.61 4.53 ns hstl (ii) 15 ma high 20 50 0.68 2.55 0.05 2.34 ? 0.44 2.59 2.29 ? ? 4.48 4.17 ns sstl2 (i) 15 ma high 30 25 0.68 1.79 0.05 1.77 ? 0.44 1.82 1.56 ? ? 1.82 1.56 ns sstl2 (ii) 18 ma high 30 50 0.68 1.83 0.05 1.77 ? 0.44 1.86 1.49 ? ? 1.86 1.49 ns sstl3 (i) 14 ma high 30 25 0.68 1.94 0.05 1.69 ? 0.44 1.98 1.55 ? ? 1.98 1.55 ns sstl3 (ii) 21 ma high 30 50 0.68 1.74 0.05 1.69 ? 0.44 1.77 1.41 ? ? 1.77 1.41 ns lvds 24 mahigh??0.681.570.052.04????????ns lvpecl 24 mahigh??0.681.540.051.84????????ns notes: 1. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. 2. resistance is used to measure i/o propagation delays as defined in pci specifications. see figure 2-13 on page 2-65 for connectivity. this resistor is not required during normal operation. www..net
military proasic3/el low-power flash fpgas v1.0 2-29 1.5 v core voltage table 2-30 ? summary of i/o timing character istics?software default settings ?1 speed grade, military-case conditions: t j = 125c, v cc = 1.425 v, worst case v cci applicable to pro i/os fo r a3pe600l and a3pe3000l only standard drive strength (ma) slew rate capacitive load (pf) external resistor ( ) t dout (ns) t dp (ns) t din (ns) t py (ns) t pys (ns) t eout (ns) t zl (ns) t zh (ns) t lz (ns) t hz (ns) t zls (ns) t zhs (ns) units 3.3 v lvttl / 3.3 v lvcmos 12 ma high 5 ? 0.52 2.08 0.03 1.48 2.03 0.34 2.12 1.56 2.76 3.04 4.00 3.44 ns 2.5 v lvcmos 12 ma high 5 ? 0.52 2.12 0.03 1.74 2.16 0.34 2.16 1.74 2.84 2.94 4.04 3.63 ns 1.8 v lvcmos 12 ma high 5 ? 0.52 2.36 0.03 1.69 2.38 0.34 2.40 1.94 3.14 3.57 4.28 3.82 ns 1.5 v lvcmos 12 ma high 5 ? 0.52 2.71 0.03 1.86 2.59 0.34 2.76 2.24 3.34 3.68 4.64 4.12 ns 3.3 v pci per pci spec high 10 25 0.52 2.36 0.03 2.31 3.12 0.34 2.41 1.68 2.76 3.04 4.29 3.56 ns 3.3 v pci-x per pci-x spec high 10 25 0.52 2.36 0.03 2.31 3.12 0.34 2.41 1.68 2.76 3.04 4.29 3.56 ns 3.3 v gtl 25 ma high 10 25 0.52 1.75 0.03 1.98 ? 0.34 1.72 1.75 ? ? 3.60 3.63 ns 2.5 v gtl 25 ma high 10 25 0.52 1.79 0.03 1.92 ? 0.34 1.82 1.79 ? ? 3.70 3.68 ns 3.3 v gtl+ 35 ma high 10 25 0.52 1.73 0.03 1.98 ? 0.34 1.76 1.73 ? ? 3.65 3.61 ns 2.5 v gtl+ 33 ma high 10 25 0.52 1.86 0.03 1.92 ? 0.34 1.89 1.77 ? ? 3.78 3.65 ns hstl (i) 8 ma high 20 25 0.52 2.68 0.03 2.34 ? 0.34 2.73 2.65 ? ? 4.61 4.53 ns hstl (ii) 15 ma high 20 50 0.52 2.55 0.03 2.34 ? 0.34 2.59 2.29 ? ? 4.48 4.17 ns sstl2 (i) 15 ma high 30 25 0.52 1.79 0.03 1.77 ? 0.34 1.82 1.56 ? ? 1.82 1.56 ns sstl2 (ii) 18 ma high 30 50 0.52 1.83 0.03 1.77 ? 0.34 1.86 1.49 ? ? 1.86 1.49 ns sstl3 (i) 14 ma high 30 25 0.52 1.94 0.03 1.69 ? 0.34 1.98 1.55 ? ? 1.98 1.55 ns sstl3 (ii) 21 ma high 30 50 0.52 1.74 0.03 1.69 ? 0.34 1.77 1.41 ? ? 1.77 1.41 ns lvds 24 mahigh??0.521.570.032.04???????? ns lvpecl 24 mahigh??0.521.540.031.84???????? ns notes: 1. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. 2. resistance is used to measure i/o propagation delays as defined in pci specifications. see figure 2-13 on page 2-65 for connectivity. this resistor is not required during normal operation. www..net
military proasic3/el low-power flash fpgas 2-30 v1.0 table 2-31 ? summary of i/o timing character istics?software default settings ?1 speed grade, military-case conditions: t j = 125c, worst case v cc = 1.425 v, worst case v cci applicable to advanced i/o banks for A3P1000 only i/o standard drive strength (ma) slew rate capacitive load (pf) external resistor ( ) t dout (ns) t dp (ns) t din (ns) t py (ns) t eout (ns) t zl (ns) t zh (ns) t lz (ns) t hz (ns) t zls (ns) t zhs (ns) units 3.3 v lvttl / 3.3 v lvcmos 12 ma high 5pf ? 0.54 2.24 0.04 0. 95 0.39 2.28 1.70 3.00 3.35 4.38 3.79 ns 2.5 v lvcmos 12 ma high 5 pf ? 0.54 2. 26 0.04 1.23 0.39 2.30 1.89 3.09 3.22 4.39 3.99 ns 1.8 v lvcmos 12 ma high 5 pf ? 0.54 2.49 0.04 1.14 0.39 2.54 2.12 3.46 3.82 4.63 4.21 ns 1.5 v lvcmos 12 ma high 5 pf ? 0.54 2.85 0.04 1.35 0.39 2.90 2.45 3.69 3.93 4.99 4.55 ns 3.3 v pci per pci spec. high 5 pf 25 2 0.54 2.51 0.04 0.81 0.39 2. 39 1.68 3.00 3.35 4.65 3.92 ns 3.3 v pci-x per pci-x spec. high 10 pf 25 2 0.54 2.51 0.04 0.78 0.39 2. 39 1.68 3.00 3.35 4.65 3.92 ns lvds 24 ma high ? ? 0.54 1. 71 0.04 1.50 n/a n/a n/a n/a n/a n/a n/a ns lvpecl 24 ma high ? ? 0.54 1. 68 0.04 1.31 n/a n/a n/a n/a n/a n/a n/a ns notes: 1. for specific junc tion temperature and voltag e supply levels, refer to table 2-6 on page 2-8 for derating values. 2. resistance is used to measure i/o propagatio n delays as defined in pci specifications. see figure 2-13 on page 2-65 for connectivity. this resistor is not required during normal operation. www..net
military proasic3/el low-power flash fpgas v1.0 2-31 detailed i/o dc characteristics table 2-32 ? summary of i/o timing character istics?software default settings ?1 speed grade, military-case conditions: t j = 125c, worst case v cc = 1.425 v, worst case v cci =3.0v applicable to standard pl us i/o banks for A3P1000 only i/o standard drive strength (ma) slew rate capacitive load (pf) external resistor t dout (ns) t dp (ns) t din (ns) t py (ns) t eout (ns) t zl (ns) t zh (ns) t lz (ns) t hz (ns) t zls (ns) t zhs (ns) units 3.3 v lvttl / 3.3 v lvcmos 12 ma high 5pf ? 0. 54 1.90 0.04 0.94 0.39 1.94 1.47 2.61 3.01 4.03 3.56 ns 2.5 v lvcmos 12 ma high 5pf ? 0.54 1.94 0.04 1.21 0.39 1.97 1.62 2.64 2.91 4.07 3.71 ns 1.8 v lvcmos 8 ma high 5pf ? 0.54 1.94 0.04 1.21 0.39 1.97 1.62 2.64 2.91 4.07 3.71 ns 1.5 v lvcmos 4 ma high 5pf ? 0.54 2.62 0.04 1.33 0.39 2.67 2.23 2.84 2.93 4.77 4.32 ns 3.3 v pci per pci sp ec. high 10 pf 25 2 0.54 2.16 0.04 0.80 0.39 2. 03 1.45 2.61 3.01 4.29 3.69 ns 3.3 v pci-x per pci-x spec. high 10 pf 25 2 0.54 2.16 0.04 0.78 0.39 2. 03 1.45 2.61 3.01 4.29 3.69 ns notes: 1. for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. 2. resistance is used to measure i/o propagatio n delays as defined in pci specifications. see figure 2-13 on page 2-65 for connectivity. this resistor is not required during normal operation. table 2-33 ? input capacitance symbol definition conditions min. max. units c in input capacitance v in = 0, f = 1.0 mhz 8 pf c inclk input capacitance on the clock pin v in = 0, f = 1.0 mhz 8 pf www..net
military proasic3/el low-power flash fpgas 2-32 v1.0 table 2-34 ? i/o output buffer maximum resistances 1 applicable to pro i/os fo r a3pe600l and a3pe3000l only standard drive strength r pull-down ( ) 2 r pull-up ( ) 3 3.3 v lvttl / 3.3 v lvcmos 4 ma 100 300 8 ma 50 150 12 ma 25 75 16 ma 17 50 24 ma 11 33 2.5 v lvcmos 4 ma 100 200 8 ma 50 100 12 ma 25 50 16 ma 20 40 24 ma 11 22 1.8 v lvcmos 2 ma 200 225 4 ma 100 112 6 ma 50 56 8 ma 50 56 12 ma 20 22 16 ma 20 22 1.5 v lvcmos 2 ma 200 224 4 ma 100 112 6 ma 67 75 8 ma 33 37 12 ma 33 37 1.2 v lvcmos 2 ma tbd tbd 3.3 v pci/pci-x per pci/pci-x specification 25 75 3.3 v gtl 25 ma 11 ? 2.5 v gtl 25 ma 14 ? 3.3 v gtl+ 35 ma 12 ? 2.5 v gtl+ 33 ma 15 ? hstl (i) 8 ma 50 50 hstl (ii) 15 ma 25 25 sstl2 (i) 15 ma 27 31 sstl2 (ii) 18 ma 13 15 sstl3 (i) 14 ma 44 69 sstl3 (ii) 21 ma 18 32 notes: 1. these maximum values are provid ed for informational reasons only . minimum output buffer resistance values depend on v cci , drive strength selection, temperature, an d process. for board design considerations and detailed output buffer resistances, use the corresponding ibis models located on the actel website at http://www.actel.co m/download/ibi s/default.aspx . 2. r (pull-down-max) = (v olspec ) / i olspec 3. r (pull-up-max) = (v ccimax ? v ohspec ) / i ohspec www..net
military proasic3/el low-power flash fpgas v1.0 2-33 table 2-35 ? i/o output buffer maximum resistances 1 applicable to advanced i/o banks for A3P1000 only standard drive strength r pull-down ( ) 2 r pull-up ( ) 3 3.3 v lvttl / 3.3 v lvcmos 2 ma 100 300 4 ma 100 300 6 ma 50 150 8 ma 50 150 12 ma 25 75 16 ma 17 50 24 ma 11 33 2.5 v lvcmos 2 ma 100 300 4 ma 100 300 6 ma 50 150 8 ma 50 150 12 ma 25 75 16 ma 17 50 24 ma 11 33 1.8 v lvcmos 2 ma 100 200 4 ma 100 200 6 ma 50 100 8 ma 50 100 12 ma 25 50 16 ma 20 40 1.5 v lvcmos 2 ma 200 224 4 ma 100 112 6 ma 67 75 8 ma 33 37 12 ma 33 37 3.3 v pci/pci-x per pci/pci-x specification 25 75 notes: 1. these maximum values are provided for information al reasons only. minimum output buffer resistance values depend on v cci , drive strength selection, temperature, an d process. for board design considerations and detailed output buffer resistances, use the corresponding ibis models located on the actel website at http://www.actel.co m/download/ibi s/default.aspx . 2. r (pull-down-max) = (v olspec ) / i olspec 3. r (pull-up-max) = (v ccimax ? v ohspec ) / i ohspec www..net
military proasic3/el low-power flash fpgas 2-34 v1.0 table 2-36 ? i/o output buffer maximum resistances 1 applicable to standard pl us i/o banks for A3P1000 only standard drive strength r pull-down ( ) 2 r pull-up ( ) 3 3.3 v lvttl / 3.3 v lvcmos 2 ma 100 300 4 ma 100 300 6 ma 50 150 8 ma 50 150 12 ma 25 75 16 ma 25 75 2.5 v lvcmos 2 ma 100 200 4 ma 100 200 6 ma 50 100 8 ma 50 100 12 ma 25 50 1.8 v lvcmos 2 ma 200 225 4 ma 100 112 6 ma 50 56 8 ma 50 56 1.5 v lvcmos 2 ma 200 224 4 ma 100 112 3.3 v pci/pci-x per pci/pci-x specification 25 75 notes: 1. these maximum values are provid ed for informational reasons only . minimum output buffer resistance values depend on v cci , drive strength selection, temperature, an d process. for board design considerations and detailed output buffer resistances, use the corresponding ibis models located on the actel website at http://www.actel.co m/download/ibi s/default.aspx . 2. r (pull-down-max) = (v olspec ) / i olspec 3. r (pull-up-max) = (v ccimax ? v ohspec ) / i ohspec www..net
military proasic3/el low-power flash fpgas v1.0 2-35 table 2-37 ? i/o weak pull-up/pull-down resistances minimum and maximum we ak pull-up/pull-down resistance values v cci r (weak pull-up) 1 ( ) r (weak pull-down) 2 ( ) min. max. min. max. 3.3 v 10 k 45 k 10 k 45 k 2.5 v 11 k 55 k 12 k 74 k 1.8 v 18 k 70 k 17 k 110 k 1.5 v 19 k 90 k 19 k 140 k 1.2 v tbd tbd tbd tbd notes: 1. r (weak pull-up-max) = (v olspec ) / i (weak pull-up-min) 2. r (weak pull-up-max) = (v ccimax ? v ohspec ) / i (weak pull-up-min) www..net
military proasic3/el low-power flash fpgas 2-36 v1.0 table 2-38 ? i/o short currents i osh /i osl applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength i osl (ma)* i osh (ma)* 3.3 v lvttl / 3.3 v lvcmos 4 ma 25 27 8 ma 51 54 12 ma 103 109 16 ma 132 127 24 ma 268 181 2.5 v lvcmos 4 ma 16 18 8 ma 32 37 12 ma 65 74 16 ma 83 87 24 ma 169 124 1.8 v lvcmos 2 ma 9 11 4 ma 17 22 6 ma 35 44 8 ma 45 51 12 ma 91 74 16 ma 91 74 1.5 v lvcmos 2 ma 13 16 4 ma 25 33 6 ma 32 39 8 ma 66 55 12 ma 66 55 1.2 v lvcmos 2ma tbd tbd 3.3 v pci/pcix per pci/pci-x specification per pci curves 3.3 v gtl 25 ma 268 181 2.5 v gtl 25 ma 169 124 3.3 v gtl+ 35 ma 268 181 2.5 v gtl+ 33 ma 169 124 hstl (i) 8 ma 32 39 hstl (ii) 15 ma 66 55 sstl2 (i) 15 ma 83 87 sstl2 (ii) 18 ma 169 124 sstl3 (i) 14 ma 51 54 sstl3 (ii) 21 ma 103 109 * t j = 100c www..net
military proasic3/el low-power flash fpgas v1.0 2-37 table 2-39 ? i/o short currents i osh /i osl applicable to advanced i/o banks for A3P1000 only drive strength i osl (ma)* i osh (ma)* 3.3 v lvttl / 3.3v lvcmos 2ma 25 27 4ma 25 27 6ma 51 54 8ma 51 54 12ma 103 109 16ma 132 127 24ma 268 181 3.3 v lvcmos 2ma 25 27 4ma 25 27 6ma 51 54 8ma 51 54 12ma 103 109 16ma 132 127 24ma 268 181 2.5 v lvcmos 2ma 16 18 4ma 16 18 6ma 32 37 8ma 32 37 12ma 65 74 16ma 83 87 24ma 169 124 1.8 v lvcmos 2ma 9 11 4ma 17 22 6ma 35 44 8ma 45 51 12ma 91 74 16ma 91 74 1.5 v lvcmos 2ma 13 16 4ma 25 33 6ma 32 39 8ma 66 55 12ma 66 55 3.3 v pci/pci-x per pci/pc i-x specification 103 109 * t j = 100c www..net
military proasic3/el low-power flash fpgas 2-38 v1.0 the length of time an i/o can withstand i osh /i osl events depends on the junction temperature. the reliability data below is based on a 3.3 v, 12 ma i/o setting, which is the worst case for this type of analysis. table 2-40 ? i/o short currents i osh /i osl applicable to standard pl us i/o banks for A3P1000 only drive strength i osl (ma)* i osh (ma)* 3.3 v lvttl / 3.3v lvcmos 2ma 25 27 4ma 25 27 6ma 51 54 8ma 51 54 12ma 103 109 16ma 103 109 2.5 v lvcmos 2ma 16 18 4ma 16 18 6ma 32 37 8ma 32 37 12ma 65 74 1.8 v lvcmos 2ma 9 11 4ma 17 22 6ma 35 44 8ma 35 44 1.5v lvcmos 2ma 13 16 4ma 25 33 3.3 v pci/pci-x per pci/ pci-x specification 103 109 * t j = 100c table 2-41 ? schmitt trigger input hysteresis, hysteresis vo ltage value (typical) fo r schmitt mode input buffers applicable to a3pe600l and a3pe3000l only input buffer configuration hysteresis value (typical) 3.3 v lvttl/lvcmos/pci/pci-x (s chmitt trigger mode) 240 mv 2.5 v lvcmos (schmitt tri gger mode) 140 mv 1.8 v lvcmos (schmitt tri gger mode) 80 mv 1.5 v lvcmos (schmitt tri gger mode) 60 mv 1.2 v lvcmos (schmi tt trigger mode) 40 mv www..net
military proasic3/el low-power flash fpgas v1.0 2-39 for example, at 110c, the short current condition would have to be sustain ed for more than three months to cause a reliability concern. the i/o desi gn does not contain any short circuit protection, but such protection would only be needed in extremely prolonged stress conditions. table 2-42 ? duration of short circui t event before failure temperature time before failure ?40c > 20 years 0c > 20 years 25c > 20 years 70c 5 years 85c 2 years 100c 6 months 110c 3 months 125c 1 month table 2-43 ? i/o input rise time, fall time, and related i/o reliability input buffer input rise/fall time (min.) input rise/fall time (max.) reliability lvttl/lvcmos no requirement 10 ns * 20 years (110c) lvds/b-lvds/ m-lvds/lvpecl no requirement 10 ns * 10 years (100c) * the maximum input rise/fall time is related to the noise induced in the input buffer trace. if the noise is low, the rise time and fall time of input buffers can be increased beyond the maximum value. the longer the rise/fall times, the more susceptible the input signal is to the board noise. actel recommends signal integrity evaluation/characterization of the system to ensure that there is no excessive noise coupling into input signals. www..net
military proasic3/el low-power flash fpgas 2-40 v1.0 single-ended i/o characteristics 3.3 v lvttl / 3.3 v lvcmos low-voltage transistor?transistor logic (lvttl) is a general-purpose standard (eia/jesd) for 3.3 v applications. it uses an lvttl input buffer and push-pull output buffer. table 2-44 ? minimum and maximum dc input and output levels applicable to pro i/os fo r a3pe600l and a3pe3000l only 3.3 v lvttl / 3.3 v lvcmos v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 4 ma ?0.3 0.8 2 3.6 0.4 2.4 4 4 25 27 15 15 8 ma ?0.3 0.8 2 3.6 0.4 2.4 8 8 51 54 15 15 12 ma ?0.3 0.8 2 3.6 0.4 2.4 12 12 103 109 15 15 16 ma ?0.3 0.8 2 3.6 0.4 2.4 16 16 132 127 15 15 24 ma ?0.3 0.8 2 3.6 0.4 2.4 24 24 268 181 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default selection highlighted in gray. table 2-45 ? minimum and maximum dc input and output levels applicable to advanced i/o banks for A3P1000 only 3.3 v lvttl / 3.3 v lvcmos v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 2 ma ?0.3 0.8 2 3.6 0.4 2.4 2 2 25 27 15 15 4 ma ?0.3 0.8 2 3.6 0.4 2.4 4 4 25 27 15 15 6 ma ?0.3 0.8 2 3.6 0.4 2.4 6 6 51 54 15 15 8 ma ?0.3 0.8 2 3.6 0.4 2.4 8 8 51 54 15 15 12 ma ?0.3 0.8 2 3.6 0.4 2.4 12 12 103 109 15 15 16 ma ?0.3 0.8 2 3.6 0.4 2.4 16 16 132 127 15 15 24 ma ?0.3 0.8 2 3.6 0.4 2.4 24 24 268 181 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default selection highlighted in gray. www..net
military proasic3/el low-power flash fpgas v1.0 2-41 table 2-46 ? minimum and maximum dc input and output levels applicable to standard pl us i/o banks for A3P1000 only 3.3 v lvttl / 3.3 v lvcmos v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 2 ma ?0.3 0.8 2 3.6 0.4 2.4 2 2 25 27 15 15 4 ma ?0.3 0.8 2 3.6 0.4 2.4 4 4 25 27 15 15 6 ma ?0.3 0.8 2 3.6 0.4 2.4 6 6 51 54 15 15 8 ma ?0.3 0.8 2 3.6 0.4 2.4 8 8 51 54 15 15 12 ma ?0.3 0.8 2 3.6 0.4 2.4 12 12 103 109 15 15 16 ma ?0.3 0.8 2 3.6 0.4 2.4 16 16 103 109 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default selection highlighted in gray. figure 2-8 ? ac loading table 2-47 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) c load (pf) 03.31.45 * measuring point = v trip. see table 2-27 on page 2-27 for a complete table of trip points. test point test point enable path datapath 35 pf r = 1 k r to v cci for t lz /t zl /t zls r to gnd for t hz /t zh /t zhs 35 pf for t zh /t zh s/t zl /t zls 5 pf for t hz /t lz www..net
military proasic3/el low-power flash fpgas 2-42 v1.0 timing characteristics 1.2 v dc core voltage table 2-48 ? 3.3 v lvttl / 3.3 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 3.0 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.80 6.03 0.05 1.74 2.39 0. 52 6.14 4.84 2.66 2.42 8.35 7.06 ns ?1 0.68 5.13 0.05 1.48 2.03 0.44 5. 22 4.12 2.27 2.06 7.11 6.00 ns 8 ma std. 0.80 4.93 0.05 1.74 2.39 0. 52 5.02 4.14 3.01 3.03 7.23 6.35 ns ?1 0.68 4.19 0.05 1.48 2.03 0.44 4. 27 3.52 2.56 2.58 6.15 5.40 ns 12 ma std. 0.80 4.15 0.05 1.74 2.39 0. 52 4.22 3.61 3.24 3.43 6.44 5.82 ns ?1 0.68 3.53 0.05 1.48 2.03 0.44 3. 59 3.07 2.76 2.92 5.47 4.95 ns 16 ma std. 0.80 3.92 0.05 1.74 2.39 0. 52 3.99 3.49 3.29 3.54 6.21 5.71 ns ?1 0.68 3.34 0.05 1.48 2.03 0.44 3. 40 2.97 2.80 3.01 5.28 4.85 ns 24 ma std. 0.80 3.81 0.05 1.74 2.39 0. 52 3.88 3.51 3.35 3.92 6.09 5.72 ns ?1 0.68 3.24 0.05 1.48 2.03 0.44 3. 30 2.98 2.85 3.34 5.18 4.87 ns note: for specific junction temperature a nd voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-49 ? 3.3 v lvttl / 3.3 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 3.0 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.80 3.39 0.05 1.74 2.39 0. 52 3.45 2.60 2.66 2.56 5.67 4.81 ns ?1 0.68 2.89 0.05 1.48 2.03 0.44 2. 94 2.21 2.27 2.18 4.82 4.10 ns 8 ma std. 0.80 2.79 0.05 1.74 2.39 0. 52 2.84 2.08 3.02 3.18 5.05 4.30 ns ?1 0.68 2.37 0.05 1.48 2.03 0.44 2. 42 1.77 2.57 2.70 4.30 3.65 ns 12 ma std. 0.80 2.45 0.05 1.74 2.39 0.52 2.49 1.83 3.24 3.58 4.71 4.05 ns ?1 0.68 2.08 0.05 1.48 2.03 0.44 2.12 1.56 2.76 3.04 4.00 3.44 ns 16 ma std. 0.80 2.39 0.05 1.74 2.39 0. 52 2.43 1.79 3.30 3.69 4.65 4.00 ns ?1 0.68 2.03 0.05 1.48 2.03 0.44 2. 07 1.52 2.80 3.14 3.95 3.40 ns 24 ma std. 0.80 2.41 0.05 1.74 2.39 0. 52 2.46 1.72 3.35 4.08 4.67 3.94 ns ?1 0.68 2.05 0.05 1.48 2.03 0.44 2. 09 1.47 2.85 3.47 3.97 3.35 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-43 1.5 v dc core voltage table 2-50 ? 3.3 v lvttl / 3.3 v lvcmos low slew military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci = 3.0 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.61 6.03 0.04 1.74 2.39 0. 40 6.14 4.84 2.66 2.42 8.35 7.06 ns ?1 0.52 5.13 0.03 1.48 2.03 0.34 5. 22 4.12 2.27 2.06 7.11 6.00 ns 8 ma std. 0.61 4.93 0.04 1.74 2.39 0. 40 5.02 4.14 3.01 3.03 7.23 6.35 ns ?1 0.52 4.19 0.03 1.48 2.03 0.34 4. 27 3.52 2.56 2.58 6.15 5.40 ns 12 ma std. 0.61 4.15 0.04 1.74 2.39 0. 40 4.22 3.61 3.24 3.43 6.44 5.82 ns ?1 0.52 3.53 0.03 1.48 2.03 0.34 3. 59 3.07 2.76 2.92 5.47 4.95 ns 16 ma std. 0.61 3.92 0.04 1.74 2.39 0. 40 3.99 3.49 3.29 3.54 6.21 5.71 ns ?1 0.52 3.34 0.03 1.48 2.03 0.34 3. 40 2.97 2.80 3.01 5.28 4.85 ns 24 ma std. 0.61 3.81 0.04 1.74 2.39 0. 40 3.88 3.51 3.35 3.92 6.09 5.72 ns ?1 0.52 3.24 0.03 1.48 2.03 0.34 3. 30 2.98 2.85 3.34 5.18 4.87 ns note: for specific junction temperature a nd voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-51 ? 3.3 v lvttl / 3.3 v lvcmos high slew military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci = 3.0 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.61 3.39 0.04 1.74 2.39 0. 40 3.45 2.60 2.66 2.56 5.67 4.81 ns ?1 0.52 2.89 0.03 1.48 2.03 0.34 2. 94 2.21 2.27 2.18 4.82 4.10 ns 8 ma std. 0.61 2.79 0.04 1.74 2.39 0. 40 2.84 2.08 3.02 3.18 5.05 4.30 ns ?1 0.52 2.37 0.03 1.48 2.03 0.34 2. 42 1.77 2.57 2.70 4.30 3.65 ns 12 ma std. 0.61 2.45 0.04 1.74 2.39 0.40 2.49 1.83 3.24 3.58 4.71 4.05 ns ?1 0.52 2.08 0.03 1.48 2.03 0.34 2.12 1.56 2.76 3.04 4.00 3.44 ns 16 ma std. 0.61 2.39 0.04 1.74 2.39 0. 40 2.43 1.79 3.30 3.69 4.65 4.00 ns ?1 0.52 2.03 0.03 1.48 2.03 0.34 2. 07 1.52 2.80 3.14 3.95 3.40 ns 24 ma std. 0.61 2.41 0.04 1.74 2.39 0. 40 2.46 1.72 3.35 4.08 4.67 3.94 ns ?1 0.52 2.05 0.03 1.48 2.03 0.34 2. 09 1.47 2.85 3.47 3.97 3.35 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-44 v1.0 table 2-52 ? 3.3 v lvttl / 3.3 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 3.0 v applicable to advanced i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.63 6.25 0.05 1.12 0.45 6.37 5.29 2.91 2. 70 8.83 7.75 ns ?1 0.54 5.32 0.04 0.95 0.39 5.42 4.50 2.47 2.30 7.51 6.59 ns 6 ma std. 0.63 5.25 0.05 1.12 0.45 5.35 4.58 3.28 3. 34 7.81 7.04 ns ?1 0.54 4.47 0.04 0.95 0.39 4.55 3.90 2.79 2.85 6.65 5.99 ns 8 ma std. 0.63 5.25 0.05 1.12 0.45 5.35 4.58 3.28 3. 34 7.81 7.04 ns ?1 0.54 4.47 0.04 0.95 0.39 4.55 3.90 2.79 2.85 6.65 5.99 ns 12 ma std. 0.63 4.50 0.05 1.12 0.45 4.59 4.05 3.53 3. 76 7.05 6.51 ns ?1 0.54 3.83 0.04 0.95 0.39 3.90 3.45 3.00 3.20 5.99 5.54 ns 16 ma std. 0.63 4.27 0.05 1.12 0.45 4.35 3.93 3.58 3. 86 6.81 6.39 ns ?1 0.54 3.63 0.04 0.95 0.39 3.70 3.34 3.05 3.29 5.79 5.43 ns 24 ma std. 0.63 4.14 0.05 1.12 0.45 4.22 3.97 3.65 4. 27 6.68 6.43 ns ?1 0.54 3.53 0.04 0.95 0.39 3.59 3.38 3.10 3.63 5.68 5.47 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. table 2-53 ? 3.3 v lvttl / 3.3 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 3.0 v applicable to advanced i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.63 3.55 0.05 1.12 0.45 3.62 2.79 2.91 2. 87 6.07 5.25 ns ?1 0.54 3.02 0.04 0.95 0.39 3.08 2.37 2.48 2.44 5.17 4.46 ns 6 ma std. 0.63 2.95 0.05 1.12 0.45 3.00 2.25 3.28 3. 52 5.46 4.71 ns ?1 0.54 2.51 0.04 0.95 0.39 2.55 1.91 2.79 3.00 4.65 4.01 ns 8 ma std. 0.63 2.95 0.05 1.12 0.45 3.00 2.25 3.28 3. 52 5.46 4.71 ns ?1 0.54 2.51 0.04 0.95 0.39 2.55 1.91 2.79 3.00 4.65 4.01 ns 12 ma std. 0.63 2.64 0.05 1.12 0.45 2.68 1.99 3.53 3.94 5.14 4.45 ns ?-1 0.54 2.24 0.04 0.95 0.39 2.28 1.70 3.00 3.35 4.38 3.79 ns 16 ma std. 0.63 2.58 0.05 1.12 0.45 2.63 1.95 3.59 4. 05 5.09 4.41 ns ?-1 0.54 2.20 0.04 0.95 0.39 2.2 4 1.66 3.05 3.44 4.33 3.75 ns 24 ma std. 0.63 2.61 0.05 1.12 0.45 2.66 1.89 3.66 4. 46 5.12 4.35 ns ?1 0.54 2.22 0.04 0.95 0.39 2.26 1.61 3.11 3.80 4.35 3.70 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-45 table 2-54 ? 3.3 v lvttl / 3.3 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 3.0 v applicable to standard pl us i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.63 5.64 0.05 1.10 0.45 5.74 4.78 2.50 2. 43 8.20 7.24 ns ?1 0.54 4.79 0.04 0.94 0.39 4.88 4.06 2.13 2.07 6.98 6.16 ns 6 ma std. 0.63 4.64 0.05 1.10 0.45 4.73 4.16 2.84 3. 01 7.19 6.62 ns ?1 0.54 3.95 0.04 0.94 0.39 4.02 3.54 2.42 2.56 6.11 5.63 ns 8 ma std. 0.63 4.64 0.05 1.10 0.45 4.73 4.16 2.84 3. 01 7.19 6.62 ns ?1 0.54 3.95 0.04 0.94 0.39 4.02 3.54 2.42 2.56 6.11 5.63 ns 12 ma std. 0.63 3.94 0.05 1.10 0.45 4.01 3.67 3.07 3. 39 6.47 6.13 ns ?1 0.54 3.35 0.04 0.94 0.39 3.41 3.12 2.61 2.88 5.51 5.21 ns 16 ma std. 0.63 3.94 0.05 1.10 0.45 4.01 3.67 3.07 3. 39 6.47 6.13 ns ?1 0.54 3.35 0.04 0.94 0.39 3.41 3.12 2.61 2.88 5.51 5.21 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. table 2-55 ? 3.3 v lvttl / 3.3 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 3.0 v applicable to standard pl us i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.63 3.07 0.05 1.10 0.45 3.13 2.46 2.50 2. 57 5.59 4.91 ns ?1 0.54 2.61 0.04 0.94 0.39 2.66 2.09 2.13 2.19 4.75 4.18 ns 6 ma std. 0.63 2.51 0.05 1.10 0.45 2.55 1.97 2.84 3. 16 5.01 4.43 ns ?1 0.54 2.13 0.04 0.94 0.39 2.17 1.67 2.41 2.69 4.26 3.76 ns 8 ma std. 0.63 2.51 0.05 1.10 0.45 2.55 1.97 2.84 3. 16 5.01 4.43 ns ?1 0.54 2.13 0.04 0.94 0.39 2.17 1.67 2.41 2.69 4.26 3.76 ns 12 ma std. 0.63 2.24 0.05 1.10 0.45 2.28 1.72 3.07 3.54 4.74 4.18 ns ?1 0.54 1.90 0.04 0.94 0.39 1.94 1.47 2.61 3.01 4.03 3.56 ns 16 ma std. 0.63 2.24 0.05 1.10 0.45 2.28 1.72 3.07 3. 54 4.74 4.18 ns ?1 0.54 1.90 0.04 0.94 0.39 1.94 1.47 2.61 3.01 4.03 3.56 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-46 v1.0 2.5 v lvcmos low-voltage cmos for 2.5 v is an extension of the lvcmos standard (jesd8-5) used for general- purpose 2.5 v applications. it uses a 5 v?tolerant input buffer and push-pull output buffer. table 2-56 ? minimum and maximum dc input and output levels applicable to pro i/os fo r a3pe600l and a3pe3000l only 2.5 v lvcmos v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 4 ma ?0.3 0.7 1.7 2.7 0.7 1.7 4 4 16 18 15 15 8 ma ?0.3 0.7 1.7 2.7 0.7 1.7 8 8 32 37 15 15 12 ma ?0.3 0.7 1.7 2.7 0.7 1.7 12 12 65 74 15 15 16 ma ?0.3 0.7 1.7 2.7 0.7 1.7 16 16 83 87 15 15 24 ma ?0.3 0.7 1.7 2.7 0.7 1.7 24 24 169 124 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default selection highlighted in gray. table 2-57 ? minimum and maximum dc input and output levels applicable to advanced i/o banks for A3P1000 only 2.5 v lvcmos v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 2 ma ?0.3 0.7 1.7 2.7 0.7 1.7 2 2 16 18 15 15 4 ma ?0.3 0.7 1.7 2.7 0.7 1.7 4 4 16 18 15 15 6 ma ?0.3 0.7 1.7 2.7 0.7 1.7 6 6 32 37 15 15 8 ma ?0.3 0.7 1.7 2.7 0.7 1.7 8 8 32 37 15 15 12 ma ?0.3 0.7 1.7 2.7 0.7 1.7 12 12 65 74 15 15 16 ma ?0.3 0.7 1.7 2.7 0.7 1.7 16 16 83 87 15 15 24 ma ?0.3 0.7 1.7 2.7 0.7 1.7 24 24 169 124 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default selection highlighted in gray. www..net
military proasic3/el low-power flash fpgas v1.0 2-47 table 2-58 ? minimum and maximum dc input and output levels applicable to standard pl us i/o banks for A3P1000 only 2.5 v lvcmos v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 2 ma ?0.3 0.7 1.7 2.7 0.7 1.7 2 2 16 18 15 15 4 ma ?0.3 0.7 1.7 2.7 0.7 1.7 4 4 16 18 15 15 6 ma ?0.3 0.7 1.7 2.7 0.7 1.7 6 6 32 37 15 15 8 ma ?0.3 0.7 1.7 2.7 0.7 1.7 8 8 32 37 15 15 12 ma ?0.3 0.7 1.7 2.7 0.7 1.7 12 12 65 74 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default selection highlighted in gray. figure 2-9 ? ac loading table 2-59 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) c load (pf) 02.51.25 * measuring point = v trip. see table 2-27 on page 2-27 for a complete table of trip points. test point test point enable path datapath 35 pf r = 1 k r to v cci for t lz /t zl /t zls r to gnd for t hz /t zh /t zhs 35 pf for t zh /t zh s/t zl /t zls 5 pf for t hz /t lz www..net
military proasic3/el low-power flash fpgas 2-48 v1.0 timing characteristics 1.2 v dc core voltage table 2-60 ? 2.5 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 2.3 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.61 6.86 0.04 2.04 2.54 0. 40 6.99 5.83 2.69 2.17 9.20 8.04 ns ?1 0.52 5.84 0.03 1.74 2.16 0.34 5. 95 4.96 2.29 1.85 7.83 6.84 ns 8 ma std. 0.61 5.61 0.04 2.04 2.54 0. 40 5.72 4.94 3.07 2.90 7.93 7.15 ns ?1 0.52 4.77 0.03 1.74 2.16 0.34 4. 86 4.20 2.61 2.47 6.75 6.08 ns 12 ma std. 0.61 4.72 0.04 2.04 2.54 0. 40 4.81 4.30 3.33 3.36 7.02 6.51 ns ?1 0.52 4.02 0.03 1.74 2.16 0.34 4. 09 3.66 2.84 2.86 5.98 5.54 ns 16 ma std. 0.61 4.45 0.04 2.04 2.54 0. 40 4.53 4.16 3.39 3.49 6.75 6.37 ns ?1 0.52 3.79 0.03 1.74 2.16 0.34 3. 86 3.54 2.88 2.97 5.74 5.42 ns 24 ma std. 0.61 4.33 0.04 2.04 2.54 0. 40 4.41 4.18 3.46 3.96 6.63 6.39 ns ?1 0.52 3.69 0.03 1.74 2.16 0.34 3. 76 3.55 2.94 3.37 5.64 5.43 ns note: for specific junction temperature a nd voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-61 ? 2.5 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 2.3 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.80 3.50 0.05 2.04 2.54 0. 52 3.57 3.13 2.69 2.26 5.78 5.34 ns ?1 0.68 2.98 0.05 1.74 2.16 0.44 3. 03 2.66 2.29 1.93 4.92 4.54 ns 8 ma std. 0.80 2.87 0.05 2.04 2.54 0. 52 2.92 2.41 3.07 3.00 5.13 4.62 ns ?1 0.68 2.44 0.05 1.74 2.16 0.44 2. 48 2.05 2.61 2.55 4.37 3.93 ns 12 ma std. 0.80 2.49 0.05 2.04 2.54 0.52 2.53 2.05 3.33 3.46 4.75 4.26 ns ?1 0.68 2.12 0.05 1.74 2.16 0.44 2.16 1.74 2.84 2.94 4.04 3.63 ns 16 ma std. 0.80 2.42 0.05 2.04 2.54 0. 52 2.47 1.99 3.39 3.59 4.68 4.20 ns ?1 0.68 2.06 0.05 1.74 2.16 0.44 2. 10 1.69 2.88 3.05 3.98 3.57 ns 24 ma std. 0.80 2.43 0.05 2.04 2.54 0. 52 2.48 1.90 3.46 4.07 4.69 4.11 ns ?1 0.68 2.07 0.05 1.74 2.16 0.44 2. 11 1.61 2.94 3.46 3.99 3.50 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-49 1.5 v dc core voltage table 2-62 ? 2.5 v lvcmos low slew military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci = 2.3 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.61 6.86 0.04 2.04 2.54 0. 40 6.99 5.83 2.69 2.17 9.20 8.04 ns ?1 0.52 5.84 0.03 1.74 2.16 0.34 5. 95 4.96 2.29 1.85 7.83 6.84 ns 8 ma std. 0.61 5.61 0.04 2.04 2.54 0. 40 5.72 4.94 3.07 2.90 7.93 7.15 ns ?1 0.52 4.77 0.03 1.74 2.16 0.34 4. 86 4.20 2.61 2.47 6.75 6.08 ns 12 ma std. 0.61 4.72 0.04 2.04 2.54 0. 40 4.81 4.30 3.33 3.36 7.02 6.51 ns ?1 0.52 4.02 0.03 1.74 2.16 0.34 4. 09 3.66 2.84 2.86 5.98 5.54 ns 16 ma std. 0.61 4.45 0.04 2.04 2.54 0. 40 4.53 4.16 3.39 3.49 6.75 6.37 ns ?1 0.52 3.79 0.03 1.74 2.16 0.34 3. 86 3.54 2.88 2.97 5.74 5.42 ns 24 ma std. 0.61 4.33 0.04 2.04 2.54 0. 40 4.41 4.18 3.46 3.96 6.63 6.39 ns ?1 0.52 3.69 0.03 1.74 2.16 0.34 3. 76 3.55 2.94 3.37 5.64 5.43 ns note: for specific junction temperature a nd voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-63 ? 2.5 v lvcmos high slew military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci = 2.3 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.61 3.50 0.04 2.04 2.54 0. 40 3.57 3.13 2.69 2.26 5.78 5.34 ns ?1 0.52 2.98 0.03 1.74 2.16 0.34 3. 03 2.66 2.29 1.93 4.92 4.54 ns 8 ma std. 0.61 2.87 0.04 2.04 2.54 0. 40 2.92 2.41 3.07 3.00 5.13 4.62 ns ?1 0.52 2.44 0.03 1.74 2.16 0.34 2. 48 2.05 2.61 2.55 4.37 3.93 ns 12 ma std. 0.61 2.49 0.04 2.04 2.54 0.40 2.53 2.05 3.33 3.46 4.75 4.26 ns ?1 0.52 2.12 0.03 1.74 2.16 0.34 2.16 1.74 2.84 2.94 4.04 3.63 ns 16 ma std. 0.61 2.42 0.04 2.04 2.54 0. 40 2.47 1.99 3.39 3.59 4.68 4.20 ns ?1 0.52 2.06 0.03 1.74 2.16 0.34 2. 10 1.69 2.88 3.05 3.98 3.57 ns 24 ma std. 0.61 2.43 0.04 2.04 2.54 0. 40 2.48 1.90 3.46 4.07 4.69 4.11 ns ?1 0.52 2.07 0.03 1.74 2.16 0.34 2. 11 1.61 2.94 3.46 3.99 3.50 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-50 v1.0 table 2-64 ? 2.5 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 2.3 v applicable to advanced i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.63 7.07 0.05 1.44 0.45 7.20 6.32 2.95 2. 43 9.66 8.78 ns ?1 0.54 6.02 0.04 1.23 0.39 6.13 5.38 2.51 2.06 8.22 7.47 ns 6 ma std. 0.63 5.91 0.05 1.44 0.45 6.02 5.42 3.35 3. 18 8.48 7.88 ns ?1 0.54 5.03 0.04 1.23 0.39 5.12 4.61 2.85 2.70 7.21 6.70 ns 8 ma std. 0.63 5.91 0.05 1.44 0.45 6.02 5.42 3.35 3. 18 8.48 7.88 ns ?1 0.54 5.03 0.04 1.23 0.39 5.12 4.61 2.85 2.70 7.21 6.70 ns 12 ma std. 0.63 5.05 0.05 1.44 0.45 5.15 4.79 3.63 3. 66 7.61 7.25 ns ?1 0.54 4.30 0.04 1.23 0.39 4.38 4.07 3.09 3.11 6.47 6.17 ns 16 ma std. 0.63 4.78 0.05 1.44 0.45 4.86 4.65 3.70 3. 78 7.32 7.10 ns ?1 0.54 4.06 0.04 1.23 0.39 4.14 3.95 3.14 3.22 6.23 6.04 ns 24 ma std. 0.63 4.71 0.05 1.44 0.45 4.73 4.71 3.78 4. 26 7.19 7.17 ns ?1 0.54 4.01 0.04 1.23 0.39 4.03 4.01 3.21 3.62 6.12 6.10 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. table 2-65 ? 2.5 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 2.3 v applicable to advanced i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.63 3.63 0.05 1.44 0.45 3.70 3.34 2.94 2. 53 6.16 5.80 ns ?1 0.54 3.09 0.04 1.23 0.39 3.15 2.84 2.51 2.16 5.24 4.94 ns 6 ma std. 0.63 2.99 0.05 1.44 0.45 3.04 2.59 3.35 3. 30 5.50 5.05 ns ?1 0.54 2.54 0.04 1.23 0.39 2.59 2.20 2.85 2.81 4.68 4.30 ns 8 ma std. 0.63 2.99 0.05 1.44 0.45 3.04 2.59 3.35 3. 30 5.50 5.05 ns ?1 0.54 2.54 0.04 1.23 0.39 2.59 2.20 2.85 2.81 4.68 4.30 ns 12 ma std. 0.63 2.65 0.05 1.44 0.45 2.70 2.23 3.63 3.78 5.16 4.69 ns ?1 0.54 2.26 0.04 1.23 0.39 2.30 1.89 3.09 3.22 4.39 3.99 ns 16 ma std. 0.63 2.59 0.05 1.44 0.45 2.64 2.16 3.70 3. 90 5.10 4.62 ns ?1 0.54 2.21 0.04 1.23 0.39 2.25 1.83 3.15 3.32 4.34 3.93 ns 24 ma std. 0.63 2.61 0.05 1.44 0.45 2.66 2.08 3.78 4. 40 5.12 4.54 ns ?1 0.54 2.22 0.04 1.23 0.39 2.26 1.77 3.22 3.74 4.35 3.87 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-51 table 2-66 ? 2.5 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 2.3 v applicable to standard pl us i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.63 6.45 0.05 1.43 0.45 6.56 5.71 2.48 2. 19 9.02 8.17 ns ?1 0.54 5.48 0.04 1.21 0.39 5.58 4.86 2.11 1.86 7.68 6.95 ns 6 ma std. 0.63 5.28 0.05 1.43 0.45 5.38 4.92 2.85 2. 88 7.84 7.38 ns ?1 0.54 4.50 0.04 1.21 0.39 4.58 4.19 2.42 2.45 6.67 6.28 ns 8 ma std. 0.63 5.28 0.05 1.43 0.45 5.38 4.92 2.85 2. 88 7.84 7.38 ns ?1 0.54 4.50 0.04 1.21 0.39 4.58 4.19 2.42 2.45 6.67 6.28 ns 12 ma std. 0.63 4.48 0.05 1.43 0.45 4.56 4.35 3.11 3. 31 7.02 6.81 ns ?1 0.54 3.81 0.04 1.21 0.39 3.88 3.70 2.65 2.82 5.97 5.79 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. table 2-67 ? 2.5 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 2.3 v applicable to standard pl us i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 4 ma std. 0.63 3.18 0.05 1.43 0.45 3.23 2.92 2.48 2. 28 5.69 5.38 ns ?1 0.54 2.70 0.04 1.21 0.39 2.75 2.48 2.11 1.94 4.84 4.58 ns 6 ma std. 0.63 2.57 0.05 1.43 0.45 2.62 2.24 2.84 2. 98 5.08 4.70 ns ?1 0.54 2.19 0.04 1.21 0.39 2.23 1.90 2.42 2.54 4.32 4.00 ns 8 ma std. 0.63 2.57 0.05 1.43 0.45 2.62 2.24 2.84 2. 98 5.08 4.70 ns ?1 0.54 2.19 0.04 1.21 0.39 2.23 1.90 2.42 2.54 4.32 4.00 ns 12 ma std. 0.63 2.28 0.05 1.43 0.45 2.32 1.90 3.11 3.42 4.78 4.36 ns ?1 0.54 1.94 0.04 1.21 0.39 1.97 1.62 2.64 2.91 4.07 3.71 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-52 v1.0 1.8 v lvcmos low-voltage cmos for 1.8 v is an extension of the lvcmos standard (jesd8-5) used for general- purpose 1.8 v applications. it uses a 1.8 v input buffer and a push-pull output buffer. table 2-68 ? minimum and maximum dc input and output levels applicable to pro i/os fo r a3pe600l and a3pe3000l only 1.8 v lvcmos v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 2 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 2 2 9 11 15 15 4 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 4 4 17 22 15 15 6 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 6 6 35 44 15 15 8 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 8 8 45 51 15 15 12 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 12 12 91 74 15 15 16 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 16 16 91 74 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default selection highlighted in gray. table 2-69 ? minimum and maximum dc input and output levels applicable to advanced i/o banks for A3P1000 only 1.8 v lvcmos v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 2 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 2 2 9 11 15 15 4 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 4 417 221515 6 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 6 635 441515 8 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 8 845 511515 12 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 12 12 91 74 15 15 16 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 16 16 91 74 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default selection highlighted in gray. www..net
military proasic3/el low-power flash fpgas v1.0 2-53 table 2-70 ? minimum and maximum dc input and output levels applicable to standard plus i/o i/o banks 1.8 v lvcmos v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 2 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 2 2 9 11 15 15 4 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 4 4 17 22 15 15 6 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 6 6 35 44 15 15 8 ma ?0.3 0.35 * v cci 0.65 * v cci 1.9 0.45 v cci ? 0.45 8 8 35 44 15 15 notes: 1. currents are measured at 100c junc tion temperature and maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default select ion highlighted in gray. figure 2-10 ? ac loading table 2-71 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) c load (pf) 01.80.95 * measuring point = v trip. see table 2-27 on page 2-27 for a complete table of trip points. test point test point enable path datapath 35 pf r = 1 k r to v cci for t lz /t zl /t zls r to gnd for t hz /t zh /t zhs 35 pf for t zh /t zh s/t zl /t zls 5 pf for t hz /t lz www..net
military proasic3/el low-power flash fpgas 2-54 v1.0 timing characteristics 1.2 v dc core voltage table 2-72 ? 1.8 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 1.7 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.80 9.15 0.05 1.98 2.80 0. 52 9.32 7.69 2.75 1.57 11.54 9.90 ns ?1 0.68 7.79 0.05 1.69 2.38 0.44 7. 93 6.54 2.34 1.33 9.81 8.42 ns 4 ma std. 0.80 7.54 0.05 1.98 2.80 0. 52 7.68 6.48 3.22 2.74 9.89 8.69 ns ?1 0.68 6.41 0.05 1.69 2.38 0.44 6. 53 5.51 2.74 2.33 8.42 7.39 ns 6 ma std. 0.80 6.39 0.05 1.98 2.80 0. 52 6.51 5.65 3.53 3.32 8.72 7.86 ns ?1 0.68 5.44 0.05 1.69 2.38 0.44 5. 54 4.80 3.00 2.83 7.42 6.69 ns 8 ma std. 0.80 6.01 0.05 1.98 2.80 0. 52 6.12 5.48 3.60 3.49 8.33 7.70 ns ?1 0.68 5.11 0.05 1.69 2.38 0.44 5. 20 4.66 3.07 2.97 7.09 6.55 ns 12 ma std. 0.80 5.89 0.05 1.98 2.80 0. 52 6.00 5.49 3.70 4.07 8.22 7.71 ns ?1 0.68 5.01 0.05 1.69 2.38 0.44 5.11 4.67 3.15 3.46 6.99 6.56 ns 16 ma std. 0.80 5.89 0.05 1.98 2.80 0. 52 6.00 5.49 3.70 4.07 8.22 7.71 ns ?1 0.68 5.01 0.05 1.69 2.38 0.44 5. 11 4.67 3.15 3.46 6.99 6.56 ns note: for specific junction temperature a nd voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-73 ? 1.8 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 1.7 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.80 4.14 0.05 1.98 2.80 0. 52 4.21 4.05 2.75 1.62 6.43 6.27 ns ?1 0.68 3.52 0.05 1.69 2.38 0.44 3. 58 3.45 2.34 1.38 5.47 5.33 ns 4 ma std. 0.80 3.35 0.05 1.98 2.80 0. 52 3.42 3.01 3.22 2.84 5.63 5.22 ns ?1 0.68 2.85 0.05 1.69 2.38 0.44 2. 91 2.56 2.74 2.41 4.79 4.44 ns 6 ma std. 0.80 2.87 0.05 1.98 2.80 0. 52 2.93 2.49 3.53 3.43 5.14 4.71 ns ?1 0.68 2.44 0.05 1.69 2.38 0.44 2. 49 2.12 3.00 2.92 4.37 4.00 ns 8 ma std. 0.80 2.78 0.05 1.98 2.80 0. 52 2.83 2.40 3.60 3.59 5.05 4.61 ns ?1 0.68 2.37 0.05 1.69 2.38 0.44 2. 41 2.04 3.06 3.05 4.29 3.92 ns 12 ma std. 0.80 2.77 0.05 1.98 2.80 0.52 2.82 2.28 3.70 4.19 5.03 4.49 ns ?1 0.68 2.36 0.05 1.69 2.38 0.44 2.40 1.94 3.14 3.57 4.28 3.82 ns 16 ma std. 0.80 2.77 0.05 1.98 2.80 0. 52 2.82 2.28 3.70 4.19 5.03 4.49 ns ?1 0.68 2.36 0.05 1.69 2.38 0.44 2. 40 1.94 3.14 3.57 4.28 3.82 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-55 1.5 v dc core voltage table 2-74 ? 1.8 v lvcmos low slew military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci = 1.7 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.61 9.15 0.04 1.98 2.80 0. 40 9.32 7.69 2.75 1.57 11.54 9.90 ns ?1 0.52 7.79 0.03 1.69 2.38 0.34 7. 93 6.54 2.34 1.33 9.81 8.42 ns 4 ma std. 0.61 7.54 0.04 1.98 2.80 0. 40 7.68 6.48 3.22 2.74 9.89 8.69 ns ?1 0.52 6.41 0.03 1.69 2.38 0.34 6. 53 5.51 2.74 2.33 8.42 7.39 ns 6 ma std. 0.61 6.39 0.04 1.98 2.80 0. 40 6.51 5.65 3.53 3.32 8.72 7.86 ns ?1 0.52 5.44 0.03 1.69 2.38 0.34 5. 54 4.80 3.00 2.83 7.42 6.69 ns 8 ma std. 0.61 6.01 0.04 1.98 2.80 0. 40 6.12 5.48 3.60 3.49 8.33 7.70 ns ?1 0.52 5.11 0.03 1.69 2.38 0.34 5. 20 4.66 3.07 2.97 7.09 6.55 ns 12 ma std. 0.61 5.89 0.04 1.98 2.80 0. 40 6.00 5.49 3.70 4.07 8.22 7.71 ns ?1 0.52 5.01 0.03 1.69 2.38 0.34 5.11 4.67 3.15 3.46 6.99 6.56 ns 16 ma std. 0.61 5.89 0.04 1.98 2.80 0. 40 6.00 5.49 3.70 4.07 8.22 7.71 ns ?1 0.52 5.01 0.03 1.69 2.38 0.34 5. 11 4.67 3.15 3.46 6.99 6.56 ns note: for specific junction temperature a nd voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-75 ? 1.8 v lvcmos high slew military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci = 1.7 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.61 4.14 0.04 1.98 2.80 0. 40 4.21 4.05 2.75 1.62 6.43 6.27 ns ?1 0.52 3.52 0.03 1.69 2.38 0.34 3. 58 3.45 2.34 1.38 5.47 5.33 ns 4 ma std. 0.61 3.35 0.04 1.98 2.80 0. 40 3.42 3.01 3.22 2.84 5.63 5.22 ns ?1 0.52 2.85 0.03 1.69 2.38 0.34 2. 91 2.56 2.74 2.41 4.79 4.44 ns 6 ma std. 0.61 2.87 0.04 1.98 2.80 0. 40 2.93 2.49 3.53 3.43 5.14 4.71 ns ?1 0.52 2.44 0.03 1.69 2.38 0.34 2. 49 2.12 3.00 2.92 4.37 4.00 ns 8 ma std. 0.61 2.78 0.04 1.98 2.80 0. 40 2.83 2.40 3.60 3.59 5.05 4.61 ns ?1 0.52 2.37 0.03 1.69 2.38 0.34 2. 41 2.04 3.06 3.05 4.29 3.92 ns 12 ma std. 0.61 2.77 0.04 1.98 2.80 0.40 2.82 2.28 3.70 4.19 5.03 4.49 ns ?1 0.52 2.36 0.03 1.69 2.38 0.34 2.40 1.94 3.14 3.57 4.28 3.82 ns 16 ma std. 0.61 2.77 0.04 1.98 2.80 0. 40 2.82 2.28 3.70 4.19 5.03 4.49 ns ?1 0.52 2.36 0.03 1.69 2.38 0.34 2. 40 1.94 3.14 3.57 4.28 3.82 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-56 v1.0 table 2-76 ? 1.8 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 1.7 v applicable to advanced i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.63 9.50 0.05 1.44 0.45 9.68 8.31 3.06 1.76 12.14 10.77 ns ?1 0.54 8.08 0.04 1.23 0.39 8.23 7.07 2.60 1.50 10.32 9.16 ns 4 ma std. 0.63 7.80 0.05 1.44 0.45 7.95 7.06 3.55 3.01 10.41 9.52 ns ?1 0.54 6.64 0.04 1.23 0.39 6.76 6.00 3.02 2.56 8.85 8.10 ns 6 ma std. 0.63 6.70 0.05 1.44 0.45 6.82 6.25 3.89 3. 60 9.28 8.70 ns ?1 0.54 5.70 0.04 1.23 0.39 5.80 5.31 3.31 3.06 7.90 7.40 ns 8 ma std. 0.63 6.31 0.05 1.44 0.45 6.43 6.07 3.97 3. 75 8.89 8.53 ns ?1 0.54 5.37 0.04 1.23 0.39 5.47 5.17 3.37 3.19 7.56 7.26 ns 12 ma std. 0.63 6.18 0.05 1.44 0.45 6.30 6.15 4.08 4. 34 8.76 8.61 ns ?1 0.54 5.26 0.04 1.23 0.39 5.36 5.23 3.47 3.70 7.45 7.32 ns 16 ma std. 0.63 6.18 0.05 1.44 0.45 6.30 6.15 4.08 4. 34 8.76 8.61 ns ?1 0.54 5.26 0.04 1.23 0.39 5.36 5.23 3.47 3.70 7.45 7.32 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. table 2-77 ? 1.8 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 1.7 v applicable to advanced i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.63 4.40 0.05 1.34 0.45 4.48 4.30 3.05 1. 82 6.94 6.76 ns ?1 0.54 3.74 0.04 1.14 0.39 3.81 3.66 2.59 1.55 5.90 5.75 ns 4 ma std. 0.63 3.44 0.05 1.34 0.45 3.50 3.23 3.54 3. 12 5.96 5.69 ns ?1 0.54 2.92 0.04 1.14 0.39 2.98 2.75 3.01 2.66 5.07 4.84 ns 6 ma std. 0.63 3.02 0.05 1.34 0.45 3.07 2.70 3.88 3. 72 5.53 5.16 ns ?1 0.54 2.57 0.04 1.14 0.39 2.61 2.30 3.30 3.16 4.71 4.39 ns 8 ma std. 0.63 2.94 0.05 1.34 0.45 2.99 2.60 3.96 3.87 5.45 5.06 ns ?1 0.54 2.50 0.04 1.14 0.39 2.54 2.21 3.37 3.30 4.64 4.31 ns 12 ma std. 0.63 2.93 0.05 1.34 0.45 2.98 2.49 4.07 4. 49 5.44 4.95 ns ?1 0.54 2.49 0.04 1.14 0.39 2.54 2.12 3.46 3.82 4.63 4.21 ns 16 ma std. 0.63 2.93 0.05 1.34 0.45 2.98 2.49 4.07 4. 49 5.44 4.95 ns ?1 0.54 2.49 0.04 1.14 0.39 2.54 2.12 3.46 3.82 4.63 4.21 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-57 table 2-78 ? 1.8 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 1.7v applicable to standard pl us i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.63 8.81 0.05 1.43 0.45 8.98 7.51 2.48 1.61 11.44 9.97 ns ?1 0.54 7.50 0.04 1.21 0.39 7.64 6.39 2.11 1.37 9.73 8.48 ns 4 ma std. 0.63 7.10 0.05 1.43 0.45 7.23 6.43 2.92 2. 75 9.69 8.89 ns ?1 0.54 6.04 0.04 1.21 0.39 6.15 5.47 2.48 2.34 8.24 7.56 ns 6 ma std. 0.63 6.06 0.05 1.43 0.45 6.17 5.68 3.23 3. 29 8.63 8.14 ns ?1 0.54 5.16 0.04 1.21 0.39 5.25 4.84 2.75 2.80 7.34 6.93 ns 8 ma std. 0.63 6.06 0.05 1.43 0.45 6.17 5.68 3.23 3. 29 8.63 8.14 ns ?1 0.54 5.16 0.04 1.21 0.39 5.25 4.84 2.75 2.80 7.34 6.93 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. table 2-79 ? 1.8 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 1.7 v applicable to standard pl us i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.63 3.94 0.05 1.32 0.45 4.01 3.72 2.47 1. 67 6.47 6.18 ns ?1 0.54 3.35 0.04 1.12 0.39 3.41 3.16 2.10 1.42 5.51 5.26 ns 4 ma std. 0.63 3.03 0.05 1.32 0.45 3.09 2.75 2.91 2. 86 5.55 5.21 ns ?1 0.54 2.58 0.04 1.12 0.39 2.63 2.34 2.48 2.44 4.72 4.43 ns 6 ma std. 0.63 2.65 0.05 1.32 0.45 2.70 2.27 3.22 3. 41 5.16 4.73 ns ?1 0.54 2.26 0.04 1.12 0.39 2.30 1.93 2.74 2.90 4.39 4.02 ns 8 ma std. 0.63 2.65 0.05 1.32 0.45 2.70 2.27 3.22 3.41 5.16 4.73 ns ?1 0.54 2.26 0.04 1.12 0.39 2.30 1.93 2.74 2.90 4.39 4.02 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-58 v1.0 1.5 v lvcmos (jesd8-11) low-voltage cmos for 1.5 v is an extension of the lvcmos standard (jesd8-5) used for general- purpose 1.5 v applications. it uses a 1.5 v input buffer and a push-pull output buffer. table 2-80 ? minimum and maximum dc input and output levels applicable to pro i/os fo r a3pe600l and a3pe3000l only 1.5 v lvcmos v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 2 ma ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 2 213 161515 4 ma ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 4 425 331515 6 ma ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 6 632 391515 8 ma ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 8 866 551515 12 ma ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 12 12 66 55 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default selection highlighted in gray. table 2-81 ? minimum and maximum dc input and output levels applicable to advanced i/o banks for A3P1000 only 1.5 v lvcmos v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 2 ma ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 2 2 13 16 15 15 4 ma ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 4 4 25 33 15 15 6 ma ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 6 6 32 39 15 15 8 ma ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 8 8 66 55 15 15 12 ma ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 12 12 66 55 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default selection highlighted in gray. www..net
military proasic3/el low-power flash fpgas v1.0 2-59 table 2-82 ? minimum and maximum dc input and output levels applicable to standard pl us i/o banks for A3P1000 only 1.5 v lvcmos v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 2 ma ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 2 2 13 16 15 15 4 ma ?0.3 0.35 * v cci 0.65 * v cci 1.575 0.25 * v cci 0.75 * v cci 4 4 25 33 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default selection highlighted in gray. figure 2-11 ? ac loading table 2-83 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) c load (pf) 01.50.755 * measuring point = v trip. see table 2-27 on page 2-27 for a complete table of trip points. test point test point enable path datapath 35 pf r = 1 k r to v cci for t lz /t zl /t zls r to gnd for t hz /t zh /t zhs 35 pf for t zh /t zh s/t zl /t zls 5 pf for t hz /t lz www..net
military proasic3/el low-power flash fpgas 2-60 v1.0 timing characteristics 1.2 v dc core voltage table 2-84 ? 1.5 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 1.4 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.80 9.52 0.05 2.19 3.05 0. 52 9.69 7.89 3.37 2.65 11.91 10.10 ns ?1 0.68 8.10 0.05 1.86 2.59 0.44 8. 25 6.71 2.87 2.26 10.13 8.59 ns 4 ma std. 0.80 8.14 0.05 2.19 3.05 0. 52 8.29 6.89 3.73 3.32 10.50 9.10 ns ?1 0.68 6.92 0.05 1.86 2.59 0.44 7. 05 5.86 3.17 2.83 8.93 7.74 ns 6 ma std. 0.80 7.64 0.05 2.19 3.05 0. 52 7.78 6.70 3.80 3.51 9.99 8.92 ns ?1 0.68 6.50 0.05 1.86 2.59 0.44 6. 62 5.70 3.24 2.99 8.50 7.59 ns 8 ma std. 0.80 7.54 0.05 2.19 3.05 0. 52 7.68 6.71 3.93 4.18 9.89 8.92 ns ?1 0.68 6.41 0.05 1.86 2.59 0.44 6. 53 5.71 3.34 3.55 8.41 7.59 ns 12 ma std. 0.80 7.54 0.05 2.19 3.05 0.52 7.68 6.71 3.93 4.18 9.89 8.92 ns ?1 0.68 6.41 0.05 1.86 2.59 0.44 6.53 5.71 3.34 3.55 8.41 7.59 ns note: for specific junction temperature a nd voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-85 ? 1.5 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 1.4 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.80 3.91 0.05 2.19 3.05 0. 52 3.98 3.54 3.36 2.76 6.19 5.76 ns ?1 0.68 3.32 0.05 1.86 2.59 0.44 3. 38 3.01 2.86 2.35 5.27 4.90 ns 4 ma std. 0.80 3.33 0.05 2.19 3.05 0. 52 3.39 2.90 3.71 3.44 5.61 5.12 ns ?1 0.68 2.83 0.05 1.86 2.59 0.44 2. 89 2.47 3.16 2.93 4.77 4.35 ns 6 ma std. 0.80 3.22 0.05 2.19 3.05 0. 52 3.28 2.78 3.80 3.63 5.49 5.00 ns ?1 0.68 2.74 0.05 1.86 2.59 0.44 2. 79 2.37 3.23 3.09 4.67 4.25 ns 8 ma std. 0.80 3.18 0.05 2.19 3.05 0. 52 3.24 2.63 3.92 4.33 5.46 4.85 ns ?1 0.68 2.71 0.05 1.86 2.59 0.44 2. 76 2.24 3.34 3.68 4.64 4.12 ns 12 ma std. 0.80 3.18 0.05 2.19 3.05 0.52 3.24 2.63 3.92 4.33 5.46 4.85 ns ?1 0.68 2.71 0.05 1.86 2.59 0.44 2.76 2.24 3.34 3.68 4.64 4.12 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-61 1.5 v dc core voltage table 2-86 ? 1.5 v lvcmos low slew military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci = 1.4 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.61 9.52 0.04 2.19 3.05 0. 40 9.69 7.89 3.37 2.65 11.91 10.10 ns ?1 0.52 8.10 0.03 1.86 2.59 0.34 8. 25 6.71 2.87 2.26 10.13 8.59 ns 4 ma std. 0.61 8.14 0.04 2.19 3.05 0. 40 8.29 6.89 3.73 3.32 10.50 9.10 ns ?1 0.52 6.92 0.03 1.86 2.59 0.34 7. 05 5.86 3.17 2.83 8.93 7.74 ns 6 ma std. 0.61 7.64 0.04 2.19 3.05 0. 40 7.78 6.70 3.80 3.51 9.99 8.92 ns ?1 0.52 6.50 0.03 1.86 2.59 0.34 6. 62 5.70 3.24 2.99 8.50 7.59 ns 8 ma std. 0.61 7.54 0.04 2.19 3.05 0. 40 7.68 6.71 3.93 4.18 9.89 8.92 ns ?1 0.52 6.41 0.03 1.86 2.59 0.34 6. 53 5.71 3.34 3.55 8.41 7.59 ns 12 ma std. 0.61 7.54 0.04 2.19 3.05 0.40 7.68 6.71 3.93 4.18 9.89 8.92 ns ?1 0.52 6.41 0.03 1.86 2.59 0.34 6.53 5.71 3.34 3.55 8.41 7.59 ns note: for specific junction temperature a nd voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-87 ? 1.5 v lvcmos high slew military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci = 1.4 v applicable to pro i/os fo r a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.61 3.91 0.04 2.19 3.05 0. 40 3.98 3.54 3.36 2.76 6.19 5.76 ns ?1 0.52 3.32 0.03 1.86 2.59 0.34 3. 38 3.01 2.86 2.35 5.27 4.90 ns 4 ma std. 0.61 3.33 0.04 2.19 3.05 0. 40 3.39 2.90 3.71 3.44 5.61 5.12 ns ?1 0.52 2.83 0.03 1.86 2.59 0.34 2. 89 2.47 3.16 2.93 4.77 4.35 ns 6 ma std. 0.61 3.22 0.04 2.19 3.05 0. 40 3.28 2.78 3.80 3.63 5.49 5.00 ns ?1 0.52 2.74 0.03 1.86 2.59 0.34 2. 79 2.37 3.23 3.09 4.67 4.25 ns 8 ma std. 0.61 3.18 0.04 2.19 3.05 0. 40 3.24 2.63 3.92 4.33 5.46 4.85 ns ?1 0.52 2.71 0.03 1.86 2.59 0.34 2. 76 2.24 3.34 3.68 4.64 4.12 ns 12 ma std. 0.61 3.18 0.04 2.19 3.05 0.40 3.24 2.63 3.92 4.33 5.46 4.85 ns ?1 0.52 2.71 0.03 1.86 2.59 0.34 2.76 2.24 3.34 3.68 4.64 4.12 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-62 v1.0 table 2-88 ? 1.5 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 1.4 v applicable to advanced i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.63 9.78 0.05 1.44 0.45 9.96 8.57 3.74 2.91 12.42 11.03 ns ?1 0.54 8.32 0.04 1.23 0.39 8.47 7.29 3.18 2.47 10.56 9.38 ns 4 ma std. 0.63 8.44 0.05 1.44 0.45 8.60 7.59 4.12 3.60 11.06 10.05 ns ?1 0.54 7.18 0.04 1.23 0.39 7.32 6.46 3.51 3.06 9.41 8.55 ns 6 ma std. 0.63 7.95 0.05 1.44 0.45 8.10 7.39 4.21 3.78 10.56 9.85 ns ?1 0.54 6.77 0.04 1.23 0.39 6.89 6.29 3.58 3.21 8.98 8.38 ns 8 ma std. 0.63 7.84 0.05 1.44 0.45 7.98 7.47 4.35 4.45 10.44 9.92 ns ?1 0.54 6.67 0.04 1.23 0.39 6.79 6.35 3.70 3.79 8.88 8.44 ns 12 ma std. 0.63 7.84 0.05 1.44 0.45 7.98 7.47 4.35 4.45 10.44 9.92 ns ?1 0.54 6.67 0.04 1.23 0.39 6.79 6.35 3.70 3.79 8.88 8.44 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. table 2-89 ? 1.5 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 1.4 v applicable to advanced i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.63 3.98 0.05 1.58 0.45 4.06 3.80 3.73 3. 04 6.52 6.26 ns ?1 0.54 3.39 0.04 1.35 0.39 3.45 3.23 3.17 2.59 5.54 5.32 ns 4 ma std. 0.63 3.47 0.05 1.58 0.45 3.53 3.15 4.11 3. 74 5.99 5.61 ns ?1 0.54 2.95 0.04 1.35 0.39 3.01 2.68 3.50 3.18 5.10 4.77 ns 6 ma std. 0.63 3.37 0.05 1.58 0.45 3.43 3.02 4.20 3. 92 5.89 5.48 ns ?1 0.54 2.87 0.04 1.35 0.39 2.92 2.57 3.57 3.33 5.01 4.66 ns 8 ma std. 0.63 3.35 0.05 1.58 0.45 3.41 2.88 4.34 4.62 5.87 5.34 ns ?1 0.54 2.85 0.04 1.35 0.39 2.90 2.45 3.69 3.93 4.99 4.55 ns 12 ma std. 0.63 3.35 0.05 1.58 0.45 3.41 2.88 4.34 4. 62 5.87 5.34 ns ?1 0.54 2.85 0.04 1.35 0.39 2.90 2.45 3.69 3.93 4.99 4.55 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-63 table 2-90 ? 1.5 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 1.4 v applicable to standard pl us i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.63 8.94 0.05 1.43 0.45 9.11 7.80 2.99 2.67 11.57 10.26 ns ?1 0.54 7.61 0.04 1.21 0.39 7.75 6.64 2.54 2.27 9.84 8.73 ns 4 ma std. 0.63 7.68 0.05 1.43 0.45 7.83 6.91 3.34 3.30 10.29 9.37 ns ?1 0.54 6.54 0.04 1.21 0.39 6.66 5.88 2.84 2.80 8.75 7.97 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. table 2-91 ? 1.5 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 1.4 v applicable to standard pl us i/o banks for A3P1000 only drive strength speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.63 3.55 0.05 1.56 0.45 3.61 3.22 2.98 2. 80 6.07 5.68 ns ?1 0.54 3.02 0.04 1.33 0.39 3.07 2.74 2.54 2.39 5.16 4.83 ns 4 ma std. 0.63 3.09 0.05 1.56 0.45 3.14 2.62 3.34 3.44 5.60 5.08 ns ?1 0.54 2.62 0.04 1.33 0.39 2.67 2.23 2.84 2.93 4.77 4.32 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-64 v1.0 1.2 v lvcmos (jesd8-12a) low-voltage cmos for 1.2 v comp lies with the lvcmos standard jesd8-12a for general purpose 1.2 v applications. it uses a 1.2 v inpu t buffer and a push-pull output buffer. timing characteristics 1.2 v dc core voltage table 2-92 ? minimum and maximum dc input and output levels applicable to pro i/o banks for a3pe600l an d a3pe3000l operating at 1.2 v core voltage 1.2 v lvcmos v il v ih v ol v oh i ol i oh i osh 1 i osl 1 i il 2 i ih 2 drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma max., ma a a 2 ma ?0.3 0.35 * v cci 0.65 * v cci 1.26 0.25 * v cci 0.75 * v cci 2 2 tbd tbd 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. software default selection highlighted in gray. figure 2-12 ? ac loading table 2-93 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) c load (pf) 01.20.65 * measuring point = v trip. see table 2-27 on page 2-27 for a complete table of trip points. test point test point enable path datapath 5 pf r = 1 k r to v cci for t lz /t zl /t zls r to gnd for t hz /t zh /t zhs 35 pf for t zh /t zh s/t zl /t zls 5 pf for t hz /t lz table 2-94 ? 1.2 v lvcmos low slew military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 1.4 v applicable to pro i/o banks for a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.80 12.62 0.05 2.62 3.76 0.52 12.07 9.47 5.12 4.68 14.20 11.60 ns ?1 0.68 10.73 0.05 2.23 3.20 0.44 10.27 8.05 4.36 3.98 12.08 9.87 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-95 ? 1.2 v lvcmos high slew military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 1.4 v applicable to pro i/o banks for a3pe600l and a3pe3000l only drive strength speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units 2 ma std. 0.80 5.17 0.05 2.62 3.76 0.52 4.95 4.36 5.11 4.83 7.08 6.49 ns ?1 0.68 4.40 0.05 2.23 3.20 0.44 4.21 3.71 4.35 4.11 6.02 5.52 ns notes: 1. software default select ion highlighted in gray. 2. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-65 3.3 v pci, 3.3 v pci-x peripheral component interface for 3.3 v standard specifies support for 33 mhz and 66 mhz pci bus applications. ac loadings are defined per the pci/pci-x specific ations for the database; actel loadings for enable path characterization are described in figure 2-13 . ac loadings are defi ned per pci/pci-x specifications for the datapath; actel loading for tristate is described in table 2-97 . table 2-96 ? minimum and maximum dc input and output levels 3.3 v pci/pci-x v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min, v max, v min, v max, v max, v min, v ma ma max, ma 1 max, ma 1 a 2 a 2 per pci specification per pci curves 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. figure 2-13 ? ac loading test point enable path r to v for t /t /t cci lz zl zls 10 pf for t /t /t /t zh zhs zls zl 5 pf for t hz /t lz r to gnd for t /t /t hz zh zh s r = 1 k test point datapath r = 25 r to v cci for t dp (f) r to gnd for t dp (r) table 2-97 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) c load (pf) 0 3.3 0.285 * v cci for t dp(r) 0.615 * v cci for t dp(f) 10 * measuring point = v trip. see table 2-27 on page 2-27 for a complete table of trip points. www..net
military proasic3/el low-power flash fpgas 2-66 v1.0 timing characteristics 1.2 v dc core voltage 1.5 v dc core voltage table 2-98 ? 3.3 v pci/pci-x military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 3.0 v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units std. 0.80 2.78 0.05 2.72 3.67 0.52 2.83 1.98 3.24 3.58 5.04 4.19 ns ?1 0.68 2.36 0.05 2.31 3.12 0.44 2.41 1.68 2.76 3.04 4.29 3.56 ns note: for specific junction temperature a nd voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-99 ? 3.3 v pci/pci-x military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci = 3.0 v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units std. 0.61 2.78 0.04 2.72 3.67 0.40 2.83 1.98 3.24 3.58 5.04 4.19 ns ?1 0.52 2.36 0.03 2.31 3.12 0.34 2.41 1.68 2.76 3.04 4.29 3.56 ns note: for specific junction temperature a nd voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-100 ? 3.3 v pci/pci-x military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 3.0 v applicable to advanced i/o banks for A3P1000 only speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units std. 0.63 2.95 0.05 0.95 0.45 2.81 1.98 3.53 3.94 5.46 4.61 0.63 ns ?1 0.54 2.51 0.04 0.81 0.39 2.39 1.68 3.00 3.35 4.65 3.92 0.54 ns note: for specific junction temperature a nd voltage supply levels, refer to table 2-6 on page 2-8 for derating values. table 2-101 ? 3.3 v pci/pci-x military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 3.0 v applicable to standard pl us i/o banks for A3P1000 only speed grade t dout t dp t din t py t pys t eout t zl t zh t lz t hz t zls t zhs units std. 0.63 2.54 0.05 0.94 0.45 2.39 1.71 3.07 3.54 5.04 4.33 0.63 ns ?1 0.54 2.16 0.04 0.80 0.39 2.03 1.45 2.61 3.01 4.29 3.69 0.54 ns note: for specific junction temperature a nd voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-67 voltage-referenced i/o characteristics 3.3 v gtl gunning transceiver logic is a high-speed bus standard (jesd8-3). it provides a differential amplifier input buffer and an open-drain output buffer. the v cci pin should be connected to 3.3 v. timing characteristics table 2-102 ? minimum and maximum dc input and output levels 3.3 v gtl v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 25 ma 3 ?0.3 v ref ? 0.05 v ref + 0.05 3.6 0.4 ? 25 25 268 181 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. output drive strength is below jedec specification. figure 2-14 ? ac loading table 2-103 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) v ref (typ.) (v) v tt (typ.) (v) c load (pf) v ref ? 0.05 v ref + 0.05 0.8 0.8 1.2 10 * measuring point = v trip . see table 2-27 on page 2-27 for a complete table of trip points. test point 10 pf 25 gtl v tt table 2-104 ? 3.3 v gtl military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci =3.0v, v ref =0.8v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.80 2.05 0.05 2.33 0. 52 2.02 2.05 4.23 4.27 ns ?1 0.68 1.75 0.05 1.98 0. 44 1.72 1.75 3.60 3.63 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-105 ? 3.3 v gtl military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci =3.0v, v ref =0.8v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.61 2.05 0.04 2.33 0. 40 2.02 2.05 4.23 4.27 ns ?1 0.52 1.75 0.03 1.98 0. 34 1.72 1.75 3.60 3.63 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-68 v1.0 2.5 v gtl gunning transceiver logic is a high-speed bus standard (jesd8-3). it provides a differential amplifier input buffer and an op en-drain output buffer. the v cci pin should be connected to 2.5 v. timing characteristics table 2-106 ? minimum and maximum dc input and output levels 2.5 gtl v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 25 ma 3 ?0.3 v ref ? 0.05 v ref + 0.05 2.7 0.4 ? 25 25 169 124 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. output drive strength is below jedec specification. figure 2-15 ? ac loading table 2-107 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) v ref (typ.) (v) v tt (typ.) (v) c load (pf) v ref ? 0.05 v ref + 0.05 0.8 0.8 1.2 10 * measuring point = v trip . see table 2-27 on page 2-27 for a complete table of trip points. test point 10 pf 25 gtl v tt table 2-108 ? 2.5 v gtl military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci =3.0v, v ref =0.8v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.80 2.11 0.05 2.26 0. 52 2.14 2.11 4.35 4.32 ns ?1 0.68 1.79 0.05 1.92 0. 44 1.82 1.79 3.70 3.68 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-109 ? 2.5 v gtl military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci =3.0v, v ref =0.8v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.61 2.11 0.04 2.26 0. 40 2.14 2.11 4.35 4.32 ns ?1 0.52 1.79 0.03 1.92 0. 34 1.82 1.79 3.70 3.68 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-69 3.3 v gtl+ gunning transceiver logic plus is a high-speed bu s standard (jesd8-3). it provides a differential amplifier input buffer and an op en-drain output buffer. the v cci pin should be connected to 3.3 v. timing characteristics table 2-110 ? minimum and maximum dc input and output levels 3.3 v gtl+ v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 35 ma ?0.3 v ref ? 0.1 v ref + 0.1 3.6 0.6 ? 35 35 268 181 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. figure 2-16 ? ac loading table 2-111 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) v ref (typ.) (v) v tt (typ.) (v) c load (pf) v ref ? 0.1 v ref + 0.1 1.0 1.0 1.5 10 * measuring point = v trip . see table 2-27 on page 2-27 for a complete table of trip points. test point 10 pf 25 gtl+ v tt table 2-112 ? 3.3 v gtl+ military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci =3.0v, v ref =1.0v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.80 2.03 0.05 2.33 0. 52 2.07 2.03 4.29 4.25 ns ?1 0.68 1.73 0.05 1.98 0. 44 1.76 1.73 3.65 3.61 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-113 ? 3.3 v gtl+ military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci =3.0v, v ref =1.0v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.61 2.03 0.04 2.33 0. 40 2.07 2.03 4.29 4.25 ns ?1 0.52 1.73 0.03 1.98 0. 34 1.76 1.73 3.65 3.61 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-70 v1.0 2.5 v gtl+ gunning transceiver logic plus is a high-speed bu s standard (jesd8-3). it provides a differential amplifier input buffer and an op en-drain output buffer. the v cci pin should be connected to 2.5 v. timing characteristics table 2-114 ? minimum and maximum dc input and output levels 2.5 v gtl+ v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 33 ma ?0.3 v ref ? 0.1 v ref + 0.1 2.7 0.6 ? 33 33 169 124 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. figure 2-17 ? ac loading table 2-115 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) v ref (typ.) (v) v tt (typ.) (v) c load (pf) v ref ? 0.1 v ref + 0.1 1.0 1.0 1.5 10 * measuring point = v trip . see table 2-27 on page 2-27 for a complete table of trip points. test point 10 pf 25 gtl+ v tt table 2-116 ? 2.5 v gtl+ military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci =2.3v, v ref =1.0v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.80 2.18 0.05 2.26 0. 52 2.22 2.08 4.44 4.29 ns ?1 0.68 1.86 0.05 1.92 0. 44 1.89 1.77 3.78 3.65 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-117 ? 2.5 v gtl+ military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci =2.3v, v ref =1.0v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.61 2.18 0.04 2.26 0. 40 2.22 2.08 4.44 4.29 ns ?1 0.52 1.86 0.03 1.92 0. 34 1.89 1.77 3.78 3.65 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-71 hstl class i high-speed transceiver logic is a general-purpos e high-speed 1.5 v bus standard (eia/jesd8-6). military proasic3e devices support class i. this pr ovides a differential ampl ifier input buffer and a push-pull output buffer. timing characteristics table 2-118 ? minimum and maximum dc input and output levels hstl class i v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 8 ma ?0.3 v ref ? 0.1 v ref + 0.1 1.575 0.4 v cci ? 0.4 8 8 32 39 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. figure 2-18 ? ac loading table 2-119 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) v ref (typ.) (v) v tt (typ.) (v) c load (pf) v ref ? 0.1 v ref + 0.10.750.750.75 20 * measuring point = v trip . see table 2-27 on page 2-27 for a complete table of trip points. test point 20 pf 50 hstl class i v tt table 2-120 ? hstl class i military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci =1.4v, v ref =0.75v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.80 3.15 0.05 2.75 0. 52 3.21 3.11 5.42 5.33 ns ?1 0.68 2.68 0.05 2.34 0. 44 2.73 2.65 4.61 4.53 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-121 ? hstl class i military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci =1.4v, v ref =0.75v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.61 3.15 0.04 2.75 0. 40 3.21 3.11 5.42 5.33 ns ?1 0.52 2.68 0.03 2.34 0. 34 2.73 2.65 4.61 4.53 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-72 v1.0 hstl class ii high-speed transceiver logic is a general-purpos e high-speed 1.5 v bus standard (eia/jesd8-6). military proasic3e devices support class ii. this pr ovides a differential amplifier input buffer and a push-pull output buffer. timing characteristics table 2-122 ? minimum and maximum dc input and output levels hstl class ii v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 15 ma 3 ?0.3 v ref ? 0.1 v ref + 0.1 1.575 0.4 v cci ? 0.4 15 15 66 55 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. 3. output drive strength is below jedec specification. figure 2-19 ? ac loading table 2-123 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) v ref (typ.) (v) v tt (typ.) (v) c load (pf) v ref ? 0.1 v ref + 0.10.750.750.75 20 * measuring point = v trip . see table 2-27 on page 2-27 for a complete table of trip points. test point 20 pf 25 hstl class ii v tt table 2-124 ? hstl class ii military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci =1.4v, v ref =0.75v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.80 2.99 0.05 2.75 0. 52 3.05 2.69 5.26 4.90 ns ?1 0.68 2.55 0.05 2.34 0. 44 2.59 2.29 4.48 4.17 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-125 ? hstl class ii military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci =1.4v, v ref =0.75v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.61 2.99 0.04 2.75 0. 40 3.05 2.69 5.26 4.90 ns ?1 0.52 2.55 0.03 2.34 0. 34 2.59 2.29 4.48 4.17 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-73 sstl2 class i stub-speed terminated logic for 2. 5 v memory bus standard (jesd8-9). military proasic3e devices support class i. this provides a differential amplifier input buffer and a push-pull output buffer. timing characteristics table 2-126 ? minimum and maximum dc input and output levels sstl2 class i v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 15 ma ?0.3 v ref ? 0.2 v ref + 0.2 2.7 0.54 v cci ? 0.62 15 15 83 87 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. figure 2-20 ? ac loading table 2-127 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) v ref (typ.) (v) v tt (typ.) (v) c load (pf) v ref ? 0.2 v ref + 0.21.251.251.25 30 * measuring point = v trip . see table 2-27 on page 2-27 for a complete table of trip points. test point 30 pf 50 25 sstl2 class i v tt table 2-128 ? sstl2 class i military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci =2.3v, v ref =1.25v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.80 2.11 0.05 2.08 0. 52 2.14 1.83 2.14 1.83 ns ?1 0.68 1.79 0.05 1.77 0. 44 1.82 1.56 1.82 1.56 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-129 ? sstl2 class i military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci =2.3v, v ref =1.25v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.61 2.11 0.04 2.08 0. 40 2.14 1.83 2.14 1.83 ns ?1 0.52 1.79 0.03 1.77 0. 34 1.82 1.56 1.82 1.56 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-74 v1.0 sstl2 class ii stub-speed terminated logic for 2. 5 v memory bus standard (jesd8-9). military proasic3e devices support class ii. this provides a differential amplifier input buffer and a push-pull output buffer. timing characteristics table 2-130 ? minimum and maximum dc input and output levels sstl2 class ii v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 18 ma ?0.3 v ref ? 0.2 v ref + 0.2 2.7 0.35 v cci ? 0.43 18 18 169 124 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. figure 2-21 ? ac loading table 2-131 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) v ref (typ.) (v) v tt (typ.) (v) c load (pf) v ref ? 0.2 v ref + 0.21.251.251.25 30 * measuring point = v trip . see table 2-27 on page 2-27 for a complete table of trip points. test point 30 pf 25 25 sstl2 class ii v tt table 2-132 ? sstl2 class ii military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci =2.3v, v ref =1.25v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.80 2.15 0.05 2.08 0. 52 2.19 1.75 2.19 1.75 ns ?1 0.68 1.83 0.05 1.77 0. 44 1.86 1.49 1.86 1.49 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-133 ? sstl2 class ii military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci =2.3v, v ref =1.25v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.61 2.15 0.04 2.08 0. 40 2.19 1.75 2.19 1.75 ns ?1 0.52 1.83 0.03 1.77 0. 34 1.86 1.49 1.86 1.49 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-75 sstl3 class i stub-speed terminated logic for 3. 3 v memory bus standard (jesd8-8). military proasic3e devices support class i. this provides a differential amplifier input buffer and a push-pull output buffer. timing characteristics table 2-134 ? minimum and maximum dc input and output levels sstl3 class i v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 14 ma ?0.3 v ref ? 0.2 v ref + 0.2 3.6 0.7 v cci ? 1.1 14 14 51 54 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. figure 2-22 ? ac loading table 2-135 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) v ref (typ.) (v) v tt (typ.) (v) c load (pf) v ref ? 0.2 v ref + 0.2 1.5 1.5 1.485 30 * measuring point = v trip . see table 2-27 on page 2-27 for a complete table of trip points. test point 30 pf 50 25 sstl3 class i v tt table 2-136 ? sstl3 class i military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci =3.0v, v ref =1.5v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.80 2.28 0.05 1.99 0. 52 2.33 1.82 2.33 1.82 ns ?1 0.68 1.94 0.05 1.69 0. 44 1.98 1.55 1.98 1.55 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-137 ? sstl3 class i military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci =3.0v, v ref =1.5v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.61 2.28 0.04 1.99 0. 40 2.33 1.82 2.33 1.82 ns ?1 0.52 1.94 0.03 1.69 0. 34 1.98 1.55 1.98 1.55 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-76 v1.0 sstl3 class ii stub-speed terminated logic for 3. 3 v memory bus standard (jesd8-8). military proasic3e devices support class ii. this provides a differential amplifier input buffer and a push-pull output buffer. timing characteristics table 2-138 ? minimum and maximum dc input and output levels sstl3 class ii v il v ih v ol v oh i ol i oh i osl i osh i il i ih drive strength min., v max., v min., v max., v max., v min., v ma ma max., ma 1 max., ma 1 a 2 a 2 21 ma ?0.3 v ref ? 0.2 v ref + 0.2 3.6 0.5 v cci ? 0.9 21 21 103 109 15 15 notes: 1. currents are measured at 100c junc tion temperature an d maximum voltage. 2. currents are measured at 125c junction temperature. figure 2-23 ? ac loading table 2-139 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) v ref (typ.) (v) v tt (typ.) (v) c load (pf) v ref ? 0.2 v ref + 0.2 1.5 1.5 1.485 30 * measuring point = v trip . see table 2-27 on page 2-27 for a complete table of trip points. test point 30 pf 25 25 sstl3 class ii v tt table 2-140 ? sstl3 class ii military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci =3.0v, v ref =1.5v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.80 2.04 0.05 1.99 0. 52 2.08 1.65 2.08 1.65 ns ?1 0.68 1.74 0.05 1.69 0. 44 1.77 1.41 1.77 1.41 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-141 ? sstl3 class ii military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci =3.0v, v ref =1.5v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py t eout t zl t zh t lz t hz t zls t zhs units std. 0.61 2.04 0.04 1.99 0. 40 2.08 1.65 2.08 1.65 ns ?1 0.52 1.74 0.03 1.69 0. 34 1.77 1.41 1.77 1.41 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-77 differential i/o characteristics physical implementation configuration of the i/o modules as a differential pair is handled by actel designer software when the user instantiates a differen tial i/o macro in the design. differential i/os can also be used in conjunction with the embedded input register (inreg), output register (outreg), enable register (enreg), and double data rate (ddr). however, there is no support for bidirectional i/os or tr istates with the lvpecl standards. lvds low-voltage differential signaling (ansi/tia/eia-644 ) is a high-speed, differential i/o standard. it requires that one data bit be carried through tw o signal lines, so two pi ns are needed. it also requires external resistor termination. the full implementation of the lvds transmitt er and receiver is shown in an example in figure 2-24 . the building blocks of the lvds transmitte r-receiver are one transmitter macro, one receiver macro, three board resistors at the transm itter end, and one resistor at the receiver end. the values for the three driv er resistors are different from those used in the lvpecl implementation because the output sta ndard specifications are different. along with lvds i/o, military proasic3 also supp orts bus lvds structure an d multipoint lvds (m- lvds) configuration (up to 40 nodes). figure 2-24 ? lvds circuit diagram and board-level implementation 140 100 z 0 = 50 z 0 = 50 165 165 + ? p n p n inbuf_lvds outbuf_lvds fpga fpga bourns part number: cat16-lv4f12 www..net
military proasic3/el low-power flash fpgas 2-78 v1.0 table 2-142 ? minimum and maximum dc input and output levels dc parameter description min. typ. max. units v cci supply voltage 2.375 2.5 2.625 v v ol output low voltage 0.9 1.075 1.25 v v oh output high voltage 1.25 1.425 1.6 v i ol 4 output lower current 0.65 0.91 1.16 ma i oh 4 output high current 0.65 0.91 1.16 ma v i input voltage 0 2.925 v i ih 3 input high leakage current 10 a i il 3 input low leakage current 10 a v odiff differential output voltage 250 350 450 mv v ocm output common mode voltage 1.125 1.25 1.375 v v icm input common mode voltage 0.05 1.25 2.35 v v idiff input differential voltage 100 350 mv notes: 1. 5% 2. differential input voltage = 350 mv. 3. currents are measured at 125c junction temperature. 4. i ol /i oh is defined by v odiff /(resistor network). table 2-143 ? ac waveforms, measuring poin ts, and capacitive loads input low (v) input high (v) measuring point* (v) 1.075 1.325 cross point * measuring point = v trip. see table 2-27 on page 2-27 for a complete table of trip points. www..net
military proasic3/el low-power flash fpgas v1.0 2-79 timing characteristics 1.2 v dc core voltage 1.5 v dc core voltage table 2-144 ? lvds military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 2.3 v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py units std. 0.80 1.81 0.05 2.39 ns ?1 0.68 1.57 0.05 2.04 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-145 ? lvds military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci = 2.3 v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py units std. 0.61 1.81 0.04 2.39 ns ?1 0.52 1.57 0.03 2.04 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-146 ? lvds military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 2.3 v applicable to advanced i/o banks for A3P1000 only speed grade t dout t dp t din t py units std. 0.63 2.01 0.05 1.76 ns ?1 0.54 1.71 0.04 1.50 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-80 v1.0 b-lvds/m-lvds bus lvds (b-lvds) and multipoint lvds (m-lvds) specifications extend th e existing lvds standard to high-performance mult ipoint bus applications. multidrop and multipoint bus configurations may contain any combination of drivers, receivers, and transceivers. actel lvds drivers provide the higher drive current required by b-lvds and m- lvds to accommodate th e loading. the drivers require series terminations for better signal qua lity and to control voltage swing. termination is also required at both ends of the bus since the driver can be located anywhere on the bus. these configurations can be implemented using the tribuf_lvds and bibuf_lvds macros along with appropriate terminations. multipoint designs usin g actel lvds macros can achieve up to 200 mhz with a maximum of 20 loads. a sa mple application is given in figure 2-25 . the input and output buffer delays are available in the lvds section in table 2-142 on page 2-78 . example: for a bus consisting of 20 equidistant loads, the following te rminations provide the required differential volt age, in worst-case industrial operating conditions, at the farthest receiver: r s =60 and r t =70 , given z 0 =50 (2") and z stub =50 (~1.5"). figure 2-25 ? b-lvds/m-lvds multipoint appl ication using lvds i/o buffers ... r t r t bibuf_lvds r + - t + - r + - t + - d + - en en en en en receiver transceiver receiver transceiver driver r s r s r s r s r s r s r s r s r s r s z stub z stub z stub z stub z stub z stub z stub z stub z 0 z 0 z 0 z 0 z 0 z 0 z 0 z 0 z 0 z 0 z 0 z 0 www..net
military proasic3/el low-power flash fpgas v1.0 2-81 lvpecl low-voltage positive emitter-coupled logic (lvpecl) is another differential i/o standard. it requires that one data bit be carried through two signal lines. like lvds, two pins are needed. it also requires external resistor termination. the full implementation of the lvds transmitt er and receiver is shown in an example in figure 2-26 . the building blocks of the lvpecl transmitt er-receiver are one tra nsmitter macro, one receiver macro, three board resistors at the transm itter end, and one resistor at the receiver end. the values for the three driver resistors are diff erent from those used in the lvds implementation because the output standard specifications are different. figure 2-26 ? lvpecl circuit diagram and board-level implementation table 2-147 ? minimum and maximum dc input and output levels dc parameter description min. max. min. max. min. max. units v cci supply voltage 3.0 3.3 3.6 v v ol output low voltage 0.96 1.27 1.06 1.43 1.30 1.57 v v oh output high voltage 1.8 2.11 1.92 2.28 2.13 2.41 v v il , v ih input low, input high voltages 0 3.3 0 3.6 0 3.9 v v odiff differential output voltage 0.625 0.97 0.625 0.97 0.625 0.97 v v ocm output common-mode voltage 1.762 1.98 1.762 1.98 1.762 1.98 v v icm input common-mode voltage 1.01 2. 57 1.01 2.57 1.01 2.57 v v idiff input differential voltage 300 300 300 mv table 2-148 ? ac waveforms, measuring points, and capacitive loads input low (v) input high (v) measuring point* (v) 1.64 1.94 cross point * measuring point = v trip. see table 2-27 on page 2-27 for a complete table of trip points. 187 w 100 z 0 = 50 z 0 = 50 100 100 + ? p n p n inbuf_lvpecl outbuf_lvpecl fpga fpga bourns part number: cat16-pc4f12 www..net
military proasic3/el low-power flash fpgas 2-82 v1.0 timing characteristics 1.2 v dc core voltage 1.5 v dc core voltage table 2-149 ? lvpecl military-case conditions: t j = 125c, worst-case v cc = 1.14 v, worst-case v cci = 3.0 v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py units std. 0.80 1.81 0.05 2.16 ns ?1 0.68 1.54 0.05 1.84 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-150 ? lvpecl military-case conditions: t j = 125c, v cc = 1.425 v, worst-case v cci = 3.0 v applicable to pro i/os fo r a3pe600l and a3pe3000l only speed grade t dout t dp t din t py units std. 0.61 1.81 0.04 2.16 ns ?1 0.52 1.54 0.03 1.84 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-151 ? lvpecl military-case conditions: t j = 125c, worst-case v cc = 1.425 v, worst-case v cci = 3.0 v applicable to advanced i/o banks for A3P1000 only speed grade t dout t dp t din t py units std. 0.63 1.98 0.05 1.54 ns ?1 0.54 1.68 0.04 1.31 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-83 i/o register specifications fully registered i/o buffers with s ynchronous enable an d asynchronous preset figure 2-27 ? timing model of registered i/ o buffers with synchronous en able and asynchronous preset inbuf inbuf inbuf tribuf clkbuf inbuf inbuf clkbuf data input i/o register with: active high enable active high preset positive-edge triggered data output register and enable output register with: active high enable active high preset postive-edge triggered pad out clk enable preset data_out data eout dout enable clk dq dfn1e1p1 pre dq dfn1e1p1 pre dq dfn1e1p1 pre d_enable a b c d e e e e f g h i j l k y core array www..net
military proasic3/el low-power flash fpgas 2-84 v1.0 table 2-152 ? parameter definition and measuring nodes parameter name parameter definition measuring nodes (from, to)* t oclkq clock-to-q of the output data register h, dout t osud data setup time for the output data register f, h t ohd data hold time for the output data register f, h t osue enable setup time for the output data register g, h t ohe enable hold time for the output data register g, h t opre2q asynchronous preset-to-q of th e output data register l, dout t orempre asynchronous preset removal time for the output data register l, h t orecpre asynchronous preset recovery time for the output data register l, h t oeclkq clock-to-q of the output enable register h, eout t oesud data setup time for the output enable register j, h t oehd data hold time for the ou tput enable register j, h t oesue enable setup time for the ou tput enable register k, h t oehe enable hold time for the output enable register k, h t oepre2q asynchronous preset-to-q of th e output enable register i, eout t oerempre asynchronous preset removal time fo r the output enable register i, h t oerecpre asynchronous preset recovery time for the output enab le register i, h t iclkq clock-to-q of the input data register a, e t isud data setup time for the input data register c, a t ihd data hold time for the input data register c, a t isue enable setup time for the input data register b, a t ihe enable hold time for the input data register b, a t ipre2q asynchronous preset-to-q of the input data register d, e t irempre asynchronous preset removal time for the input data register d, a t irecpre asynchronous preset recovery time for the input data register d, a * see figure 2-27 on page 2-83 for more information. www..net
military proasic3/el low-power flash fpgas v1.0 2-85 fully registered i/o buffers with s ynchronous enable an d asynchronous clear figure 2-28 ? timing model of the registered i/o buffers with synchronous enable and asynchronous clear enable clk pad out clk enable clr data_out data y aa eout dout core array dq dfn1e1c1 e clr dq dfn1e1c1 e clr dq dfn1e1c1 e clr d_e nable bb cc dd ee ff gg ll hh jj kk clkbuf inbuf inbuf tribuf inbuf inbuf clkbuf inbuf data input i/o register with active high enable active high clear positive-edge triggered data output register and enable output register with active high enable active high clear positive-edge triggered www..net
military proasic3/el low-power flash fpgas 2-86 v1.0 table 2-153 ? parameter definition and measuring nodes parameter name parameter definition measuring nodes (from, to)* t oclkq clock-to-q of the output data register hh, dout t osud data setup time for the output data register ff, hh t ohd data hold time for the output data register ff, hh t osue enable setup time for the output data register gg, hh t ohe enable hold time for the output data register gg, hh t oclr2q asynchronous clear-to-q of the output data register ll, dout t oremclr asynchronous clear removal time fo r the output data register ll, hh t orecclr asynchronous clear reco very time for the output data register ll, hh t oeclkq clock-to-q of the output enable register hh, eout t oesud data setup time for the ou tput enable register jj, hh t oehd data hold time for the output enable register jj, hh t oesue enable setup time for the ou tput enable register kk, hh t oehe enable hold time for the ou tput enable register kk, hh t oeclr2q asynchronous clear-to-q of the output enable register ii, eout t oeremclr asynchronous clear removal time fo r the output enab le register ii, hh t oerecclr asynchronous clear recove ry time for the output enable register ii, hh t iclkq clock-to-q of the input data register aa, ee t isud data setup time for the input data register cc, aa t ihd data hold time for the input data register cc, aa t isue enable setup time for the input data register bb, aa t ihe enable hold time for the input data register bb, aa t iclr2q asynchronous clear-to-q of the input data register dd, ee t iremclr asynchronous clear removal time for the input data register dd, aa t irecclr asynchronous clear reco very time for the inpu t data register dd, aa * see figure 2-28 on page 2-85 for more information. www..net
military proasic3/el low-power flash fpgas v1.0 2-87 input register figure 2-29 ? input register timing diagram 50 % preset clear out_1 clk data enable t isue 50 % 50 % t isud t ihd 50 % 50 % t iclkq 1 0 t ihe t irecpre t irempre t irecclr t iremclr t iwclr t iwpre t ipre2q t iclr2q t ickmpwh t ickmpwl 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % www..net
military proasic3/el low-power flash fpgas 2-88 v1.0 timing characteristics table 2-154 ? input data register propagation delays military-case conditions: t j = 125c, worst-case v cc = 1.14 v for a3pe600l and a3pe3000l parameter description ?1 std. units t iclkq clock-to-q of the input data register 0.33 0.39 ns t isud data setup time for the input data register 0.36 0.43 ns t ihd data hold time for the in put data register 0.00 0.00 ns t isue enable setup time for the input data register 0.51 0.60 ns t ihe enable hold time for the input data register 0.00 0.00 ns t iclr2q asynchronous clear-to-q of the input data register 0.63 0.74 ns t ipre2q asynchronous preset-to-q of the input data register 0.63 0.74 ns t iremclr asynchronous clear removal time fo r the input data register 0.00 0.00 ns t irecclr asynchronous clear recovery time fo r the input data register 0.31 0.36 ns t irempre asynchronous preset removal time fo r the input data register 0.00 0.00 ns t irecpre asynchronous preset recovery time for the input data register 0.31 0.36 ns t iwclr asynchronous clear minimum pulse width for the input data register 0.19 0.22 ns t iwpre asynchronous preset minimum pulse widt h for the input data register 0.19 0.22 ns t ickmpwh clock minimum pulse width high for the input data register 0.31 0.36 ns t ickmpwl clock minimum pulse width low for the input data register 0.28 0.32 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-155 ? input data register propagation delays military-case conditions: t j = 125c, v cc = 1.425 v for a3pe600l and a3pe3000l parameter description ?1 std. units t iclkq clock-to-q of the input data register 0.25 0.30 ns t isud data setup time for the input data register 0.28 0.33 ns t ihd data hold time for the in put data register 0.00 0.00 ns t isue enable setup time for the input data register 0.39 0.46 ns t ihe enable hold time for the input data register 0.00 0.00 ns t iclr2q asynchronous clear-to-q of the input data register 0.48 0.56 ns t ipre2q asynchronous preset-to-q of the input data register 0.48 0.56 ns t iremclr asynchronous clear removal time fo r the input data register 0.00 0.00 ns t irecclr asynchronous clear recovery time fo r the input data register 0.24 0.28 ns t irempre asynchronous preset removal time fo r the input data register 0.00 0.00 ns t irecpre asynchronous preset recovery time for the input data register 0.24 0.28 ns t iwclr asynchronous clear minimum pulse width for the input data register 0.19 0.22 ns t iwpre asynchronous preset minimum pulse widt h for the input data register 0.19 0.22 ns t ickmpwh clock minimum pulse width high for the input data register 0.31 0.36 ns t ickmpwl clock minimum pulse width low for the input data register 0.28 0.32 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-89 table 2-156 ? input data register propagation delays military-case conditions: t j = 125c, worst-case v cc = 1.425 v for A3P1000 parameter description ?1 std. units t iclkq clock-to-q of the input data register 0.29 0.34 ns t isud data setup time for the input data register 0.32 0.37 ns t ihd data hold time for the in put data register 0.00 0.00 ns t isue enable setup time for the input data register 0.45 0.53 ns t ihe enable hold time for the input data register 0.00 0.00 ns t iclr2q asynchronous clear-to-q of the input data register 0.55 0.64 ns t ipre2q asynchronous preset-to-q of the input data register 0.55 0.64 ns t iremclr asynchronous clear removal time fo r the input data register 0.00 0.00 ns t irecclr asynchronous clear recovery time fo r the input data register 0.27 0.31 ns t irempre asynchronous preset removal time fo r the input data register 0.00 0.00 ns t irecpre asynchronous preset recovery time for the input data register 0.27 0.31 ns t iwclr asynchronous clear minimum pulse width for the input data register 0.25 0.30 ns t iwpre asynchronous preset minimum pulse widt h for the input data register 0.25 0.30 ns t ickmpwh clock minimum pulse width high for the input data register 0.41 0.48 ns t ickmpwl clock minimum pulse width low for the input data register 0.37 0.43 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-90 v1.0 output register figure 2-30 ? output register timing diagram preset clear dout clk data_out enable t osue 50 % 50 % t osud t ohd 50 % 50 % t oclkq 1 0 t ohe t orecpre t orempre t orecclr t oremclr t owclr t owpre t opre2q t oclr2q t ockmpwh t ockmpwl 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % www..net
military proasic3/el low-power flash fpgas v1.0 2-91 timing characteristics table 2-157 ? output data register propagation delays military-case conditions: t j = 125c, worst-case v cc = 1.14 v for a3pe600l and a3pe3000l parameter description ?1 std. units t oclkq clock-to-q of the output data register 0.81 0.96 ns t osud data setup time for the output data register 0.43 0.51 ns t ohd data hold time for the output data register 0.00 0.00 ns t osue enable setup time for the ou tput data register 0.61 0.71 ns t ohe enable hold time for the output data register 0.00 0.00 ns t oclr2q asynchronous clear-to-q of the output data register 1.11 1.31 ns t opre2q asynchronous preset-to-q of the output data register 1.11 1.31 ns t oremclr asynchronous clear removal time for the output data register 0.00 0.00 ns t orecclr asynchronous clear recovery time fo r the output data register 0.31 0.36 ns t orempre asynchronous preset removal time fo r the output data register 0.00 0.00 ns t orecpre asynchronous preset reco very time for the output data register 0.31 0.36 ns t owclr asynchronous clear minimum pulse width for the output data register 0.19 0.22 ns t owpre asynchronous preset minimum pulse width for the output data register 0.19 0.22 ns t ockmpwh clock minimum pulse width high for the output data register 0.31 0.36 ns t ockmpwl clock minimum pulse width low for the output data register 0.28 0.32 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-158 ? output data register propagation delays military-case conditions: t j = 125c, v cc = 1.425 v for a3pe600l and a3pe3000l parameter description ?1 std. units t oclkq clock-to-q of the output data register 0.62 0.73 ns t osud data setup time for the output data register 0.33 0.39 ns t ohd data hold time for the output data register 0.00 0.00 ns t osue enable setup time for the ou tput data register 0.46 0.55 ns t ohe enable hold time for the output data register 0.00 0.00 ns t oclr2q asynchronous clear-to-q of the output data register 0.85 1.00 ns t opre2q asynchronous preset-to-q of the output data register 0.85 1.00 ns t oremclr asynchronous clear removal time for the output data register 0.00 0.00 ns t orecclr asynchronous clear recovery time fo r the output data register 0.24 0.28 ns t orempre asynchronous preset removal time fo r the output data register 0.00 0.00 ns t orecpre asynchronous preset reco very time for the output data register 0.24 0.28 ns t owclr asynchronous clear minimum pulse width for the output data register 0.19 0.22 ns t owpre asynchronous preset minimum pulse width for the output data register 0.19 0.22 ns t ockmpwh clock minimum pulse width high for the output data register 0.31 0.36 ns t ockmpwl clock minimum pulse width low for the output data register 0.28 0.32 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-92 v1.0 table 2-159 ? output data register propagation delays military-case conditions: t j = 125c, worst-case v cc = 1.425 v for A3P1000 parameter description ?1 std. units t oclkq clock-to-q of the output data register 0.71 0.83 ns t osud data setup time for the output data register 0.38 0.44 ns t ohd data hold time for the output data register 0.00 0.00 ns t osue enable setup time for the ou tput data register 0.53 0.62 ns t ohe enable hold time for the output data register 0.00 0.00 ns t oclr2q asynchronous clear-to-q of the output data register 0.97 1.14 ns t opre2q asynchronous preset-to-q of the output data register 0.97 1.14 ns t oremclr asynchronous clear removal time for the output data register 0.00 0.00 ns t orecclr asynchronous clear recovery time fo r the output data register 0.27 0.31 ns t orempre asynchronous preset removal time fo r the output data register 0.00 0.00 ns t orecpre asynchronous preset reco very time for the output data register 0.27 0.31 ns t owclr asynchronous clear minimum pulse width for the output data register 0.25 0.30 ns t owpre asynchronous preset minimum pulse width for the output data register 0.25 0.30 ns t ockmpwh clock minimum pulse width high for the output data register 0.41 0.48 ns t ockmpwl clock minimum pulse width low for the output data register 0.37 0.43 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-93 output enable register figure 2-31 ? output enable regist er timing diagram 50 % preset clear eout clk d_enable enable t oesue 50 % 50 % t oesud t oehd 50 % 50 % t oeclkq 1 0 t oehe t oerecpre t oerempre t oerecclr t oeremclr t oewclr t oewpre t oepre2q t oeclr2q t oeckmpwh t oeckmpwl 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % www..net
military proasic3/el low-power flash fpgas 2-94 v1.0 timing characteristics table 2-160 ? output enable register propagation delays military-case conditions: t j = 125c, worst-case v cc = 1.14 v for a3pe600l and a3pe3000l parameter description ?1 std. units t oeclkq clock-to-q of the output enable register 0.62 0.72 ns t oesud data setup time for the output enable register 0.43 0.51 ns t oehd data hold time for the outp ut enable register 0.00 0.00 ns t oesue enable setup time for the outp ut enable register 0.60 0.71 ns t oehe enable hold time for the output enable register 0.00 0.00 ns t oeclr2q asynchronous clear-to-q of the output enable register 0.92 1.08 ns t oepre2q asynchronous preset-to-q of the output enable register 0.92 1.08 ns t oeremclr asynchronous clear removal time for the output enable register 0.00 0.00 ns t oerecclr asynchronous clear recovery time for the output enable register 0.31 0.36 ns t oerempre asynchronous preset removal time for the output enable register 0.00 0.00 ns t oerecpre asynchronous preset recove ry time for the output enable register 0.31 0.36 ns t oewclr asynchronous clear minimum pulse width fo r the output enable register 0.19 0.22 ns t oewpre asynchronous preset minimum pulse width for the output enable register 0.19 0.22 ns t oeckmpwh clock minimum pulse width high for th e output enable register 0.31 0.36 ns t oeckmpwl clock minimum pulse width low for th e output enable register 0.28 0.32 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-161 ? output enable register propagation delays military-case conditions: t j = 125c, v cc = 1.425 v for a3pe600l and a3pe3000l parameter description ?1 std. units t oeclkq clock-to-q of the output enable register 0.47 0.55 ns t oesud data setup time for the output enable register 0.33 0.39 ns t oehd data hold time for the outp ut enable register 0.00 0.00 ns t oesue enable setup time for the outp ut enable register 0.46 0.54 ns t oehe enable hold time for the output enable register 0.00 0.00 ns t oeclr2q asynchronous clear-to-q of the output enable register 0.70 0.83 ns t oepre2q asynchronous preset-to-q of the output enable register 0.70 0.83 ns t oeremclr asynchronous clear removal time for the output enable register 0.00 0.00 ns t oerecclr asynchronous clear recovery time for the output enable register 0.24 0.28 ns t oerempre asynchronous preset removal time for the output enable register 0.00 0.00 ns t oerecpre asynchronous preset recove ry time for the output enable register 0.24 0.28 ns t oewclr asynchronous clear minimum pulse width fo r the output enable register 0.19 0.22 ns t oewpre asynchronous preset minimum pulse width for the output enable register 0.19 0.22 ns t oeckmpwh clock minimum pulse width high for th e output enable register 0.31 0.36 ns t oeckmpwl clock minimum pulse width low for th e output enable register 0.28 0.32 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-95 table 2-162 ? output enable register propagation delays military-case conditions: t j = 125c, worst-case v cc = 1.425 v for A3P1000 parameter description ?1 std. units t oeclkq clock-to-q of the output enable register 0.54 0.63 ns t oesud data setup time for the output enable register 0.38 0.44 ns t oehd data hold time for the outp ut enable register 0.00 0.00 ns t oesue enable setup time for the outp ut enable register 0.52 0.62 ns t oehe enable hold time for the output enable register 0.00 0.00 ns t oeclr2q asynchronous clear-to-q of the output enable register 0.80 0.94 ns t oepre2q asynchronous preset-to-q of the output enable register 0.80 0.94 ns t oeremclr asynchronous clear removal time for the output enable register 0.00 0.00 ns t oerecclr asynchronous clear recovery time for the output enable register 0.27 0.31 ns t oerempre asynchronous preset removal time for the output enable register 0.00 0.00 ns t oerecpre asynchronous preset recove ry time for the output enable register 0.27 0.31 ns t oewclr asynchronous clear minimum pulse width fo r the output enable register 0.25 0.30 ns t oewpre asynchronous preset minimum pulse width for the output enable register 0.25 0.30 ns t oeckmpwh clock minimum pulse width high for th e output enable register 0.41 0.48 ns t oeckmpwl clock minimum pulse width low for th e output enable register 0.37 0.43 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-96 v1.0 ddr module specifications input ddr module figure 2-32 ? input ddr timing model table 2-163 ? parameter definitions parameter name parameter definiti on measuring nodes (from, to) t ddriclkq1 clock-to-out out_qr b, d t ddriclkq2 clock-to-out out_qf b, e t ddrisud data setup time of ddr input a, b t ddrihd data hold time of ddr input a, b t ddriclr2q1 clear-to-out out_qr c, d t ddriclr2q2 clear-to-out out_qf c, e t ddriremclr clear removal c, b t ddrirecclr clear recovery c, b input ddr data clk clkbuf inbuf out_qf (to core) ff2 ff1 inbuf clr ddr_in e a b c d out_qr (to core) www..net
military proasic3/el low-power flash fpgas v1.0 2-97 timing characteristics figure 2-33 ? input ddr timing diagram t ddriclr2q2 t ddriremclr t ddrirecclr t ddriclr2q1 12 3 4 5 6 7 8 9 clk data clr out_qr out_qf t ddriclkq1 2 4 6 3 5 7 t ddrihd t ddrisud t ddriclkq2 table 2-164 ? input ddr propagation delays military-case conditions: t j = 125c, worst-case v cc = 1.14 v for a3pe600l and a3pe3000l parameter description ?1 std. units t ddriclkq1 clock-to-out out_qr for input ddr 0.38 0.45 ns t ddriclkq2 clock-to-out out_qf for input ddr 0.54 0.63 ns t ddrisud1 data setup for input ddr (fall) 0.39 0.46 ns t ddrisud2 data setup for input ddr (rise) 0.34 0.40 ns t ddrihd1 data hold for input ddr (fall) 0.00 0.00 ns t ddrihd2 data hold for input ddr (rise) 0.00 0.00 ns t ddriclr2q1 asynchronous clear-to-out ou t_qr for input ddr 0.64 0.75 ns t ddriclr2q2 asynchronous clear-to-out ou t_qf for input ddr 0.79 0.93 ns t ddriremclr asynchronous clear removal time for input ddr 0.00 0.00 ns t ddrirecclr asynchronous clear recovery time for input ddr 0.31 0.36 ns t ddriwclr asynchronous clear mi nimum pulse width for input ddr 0.19 0.22 ns t ddrickmpwh clock minimum pulse width high for input ddr 0.31 0.36 ns t ddrickmpwl clock minimum pulse width low for input ddr 0.28 0.32 ns f ddrimax maximum frequency fo r input ddr tbd tbd mhz note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-98 v1.0 table 2-165 ? input ddr propagation delays military-case conditions: t j = 125c, v cc = 1.425 v for any a3pe600l/a3pe3000l parameter description ?1 std. units t ddriclkq1 clock-to-out out_qr for input ddr 0.29 0.34 ns t ddriclkq2 clock-to-out out_qf for input ddr 0.41 0.48 ns t ddrisud1 data setup for input ddr (fall) 0.30 0.35 ns t ddrisud2 data setup for input ddr (rise) 0.26 0.31 ns t ddrihd1 data hold for input ddr (fall) 0.00 0.00 ns t ddrihd2 data hold for input ddr (rise) 0.00 0.00 ns t ddriclr2q1 asynchronous clear-to-out ou t_qr for input ddr 0.49 0.58 ns t ddriclr2q2 asynchronous clear-to-out ou t_qf for input ddr 0.60 0.71 ns t ddriremclr asynchronous clear removal time for input ddr 0.00 0.00 ns t ddrirecclr asynchronous clear recovery time for input ddr 0.24 0.28 ns t ddriwclr asynchronous clear mi nimum pulse width for input ddr 0.19 0.22 ns t ddrickmpwh clock minimum pulse width high for input ddr 0.31 0.36 ns t ddrickmpwl clock minimum pulse width low for input ddr 0.28 0.32 ns f ddrimax maximum frequency fo r input ddr tbd tbd mhz note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-166 ? input ddr propagation delays military-case conditions: t j = 125c, worst-case v cc = 1.425 v for A3P1000 parameter description ?1 std. units t ddriclkq1 clock-to-out out_qr for input ddr 0.33 0.39 ns t ddriclkq2 clock-to-out out_qf for input ddr 0.47 0.55 ns t ddrisud1 data setup for input ddr (fall) 0.30 0.35 ns t ddrisud2 data setup for input ddr (rise) 0.30 0.35 ns t ddrihd1 data hold for input ddr (fall) 0.00 0.00 ns t ddrihd2 data hold for input ddr (rise) 0.00 0.00 ns t ddriclr2q1 asynchronous clear-to-out ou t_qr for input ddr 0.56 0.65 ns t ddriclr2q2 asynchronous clear-to-out ou t_qf for input ddr 0.69 0.81 ns t ddriremclr asynchronous clear removal time for input ddr 0.00 0.00 ns t ddrirecclr asynchronous clear recovery time for input ddr 0.27 0.31 ns t ddriwclr asynchronous clear mi nimum pulse width for input ddr 0.25 0.30 ns t ddrickmpwh clock minimum pulse width high for input ddr 0.41 0.48 ns t ddrickmpwl clock minimum pulse width low for input ddr 0.37 0.43 ns f ddrimax maximum frequency fo r input ddr tbd tbd mhz note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-99 output ddr module figure 2-34 ? output ddr timing model table 2-167 ? parameter definitions parameter name parameter definiti on measuring nodes (from, to) t ddroclkq clock-to-out b, e t ddroclr2q asynchronous clear-to-out c, e t ddroremclr clear removal c, b t ddrorecclr clear recovery c, b t ddrosud1 data setup data_f a, b t ddrosud2 data setup data_r d, b t ddrohd1 data hold data_f a, b t ddrohd2 data hold data_r d, b data_f (from core) clk clkbuf out ff2 inbuf clr ddr_out output ddr ff1 0 1 x x x x x x x x a b d e c c b outbuf data_r (from core) www..net
military proasic3/el low-power flash fpgas 2-100 v1.0 timing characteristics figure 2-35 ? output ddr timing diagram 11 6 1 7 2 8 3 910 45 28 3 9 t ddroremclr t ddrohd1 t ddroremclr t ddrohd2 t ddrosud2 t ddroclkq t ddrorecclr clk data_r data_f clr out t ddroclr2q 710 4 table 2-168 ? output ddr propagation delays military-case conditions: t j = 125c, worst-case v cc = 1.14 v for a3pe600l and a3pe3000l parameter description ?1 std. units t ddroclkq clock-to-out of ddr for output ddr 0.97 1.14 ns t ddrisud1 data_f data setup for output ddr 0.52 0.62 ns t ddrosud2 data_r data setup for output ddr 0.52 0.62 ns t ddrohd1 data_f data hold for output ddr 0.00 0.00 ns t ddrohd2 data_r data hold for output ddr 0.00 0.00 ns t ddroclr2q asynchronous clear-to-out for output ddr 1.11 1.30 ns t ddroremclr asynchronous clear removal time for output ddr 0.00 0.00 ns t ddrorecclr asynchronous clear recovery time for output ddr 0.31 0.36 ns t ddrowclr1 asynchronous clear minimum puls e width for output ddr 0.19 0.22 ns t ddrockmpwh clock minimum pulse width high for the output ddr 0.31 0.36 ns t ddrockmpwl clock minimum pulse width low for the output ddr 0.28 0.32 ns f ddomax maximum frequenc y for the output ddr tbd tbd mhz note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-101 table 2-169 ? output ddr propagation delays military-case conditions: t j = 125c, v cc = 1.425 v for a3pe600l/a3pe3000l parameter description ?1 std. units t ddroclkq clock-to-out of ddr for output ddr 0.74 0.87 ns t ddrisud1 data_f data setup for output ddr 0.40 0.47 ns t ddrosud2 data_r data setup for output ddr 0.40 0.47 ns t ddrohd1 data_f data hold for output ddr 0.00 0.00 ns t ddrohd2 data_r data hold for output ddr 0.00 0.00 ns t ddroclr2q asynchronous clear-to-out for output ddr 0.85 1.00 ns t ddroremclr asynchronous clear removal time for output ddr 0.00 0.00 ns t ddrorecclr asynchronous clear recovery time for output ddr 0.24 0.28 ns t ddrowclr1 asynchronous clear minimum puls e width for output ddr 0.19 0.22 ns t ddrockmpwh clock minimum pulse width high for the output ddr 0.31 0.36 ns t ddrockmpwl clock minimum pulse width low for the output ddr 0.28 0.32 ns f ddomax maximum frequenc y for the output ddr tbd tbd mhz note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-102 v1.0 table 2-170 ? output ddr propagation delays military-case conditions: t j = 125c, worst-case v cc = 1.425 v for A3P1000 parameter description ?1 std. units t ddroclkq clock-to-out of ddr for output ddr 0.84 0.99 ns t ddrisud1 data_f data setup for output ddr 0.46 0.54 ns t ddrosud2 data_r data setup for output ddr 0.46 0.54 ns t ddrohd1 data_f data hold for output ddr 0.00 0.00 ns t ddrohd2 data_r data hold for output ddr 0.00 0.00 ns t ddroclr2q asynchronous clear-to-out for output ddr 0.96 1.13 ns t ddroremclr asynchronous clear removal time for output ddr 0.00 0.00 ns t ddrorecclr asynchronous clear recovery time for output ddr 0.27 0.31 ns t ddrowclr1 asynchronous clear minimum puls e width for output ddr 0.25 0.30 ns t ddrockmpwh clock minimum pulse width high for the output ddr 0.41 0.48 ns t ddrockmpwl clock minimum pulse width low for the output ddr 0.37 0.43 ns f ddomax maximum frequenc y for the output ddr tbd tbd mhz note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-103 versatile characteristics versatile specifications as a combinatorial module the military proasic3 library offers all combinations of lut-3 combinatorial functions. in this section, timing characteri stics are presented for a sample of th e library. for more details, refer to the igloo, fusion, and proasi c3 macro library guide . figure 2-36 ? sample of combinatorial cells maj3 a c by mux2 b 0 1 a s y ay b b a xor2 y nor2 b a y b a y or2 inv a y and2 b a y nand3 b a c xor3 y b a c nand2 www..net
military proasic3/el low-power flash fpgas 2-104 v1.0 figure 2-37 ? timing model and waveforms t pd a b t pd = max(t pd(rr) , t pd(rf) , t pd(ff) , t pd(fr) ) where edges are applicable for the particular combinatorial cell y nand2 or any combinatorial logic t pd t pd 50 % v cc v cc v cc 50 % gnd a, b, c 50 % 50 % 50 % (rr) (rf) gnd out out gnd 50 % (ff) (fr) t pd t pd www..net
military proasic3/el low-power flash fpgas v1.0 2-105 timing characteristics table 2-171 ? combinatorial cell propagation delays military-case conditions: t j = 125c, worst-case v cc = 1.14 v for a3pe600l and a3pe3000l combinatorial cell equation parameter ?1 std. units inv y = !a t pd 0.56 0.65 ns and2 y = a b t pd 0.65 0.77 ns nand2 y = !(a b) t pd 0.65 0.77 ns or2 y = a + b t pd 0.67 0.79 ns nor2 y = !(a + b) t pd 0.67 0.79 ns xor2 y = a bt pd 1.02 1.20 ns maj3 y = maj(a , b, c) t pd 0.97 1.14 ns xor3 y = a b ct pd 1.21 1.42 ns mux2 y = a !s + b s t pd 0.70 0.82 ns and3 y = a b c t pd 0.78 0.91 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-172 ? combinatorial cell propagation delays military-case conditions: t j = 125c, v cc = 1.425 v for any a3pe600l/a3pe3000l combinatorial cell equation parameter ?1 std. units inv y = !a t pd 0.43 0.50 ns and2 y = a b t pd 0.50 0.59 ns nand2 y = !(a b) t pd 0.50 0.59 ns or2 y = a + b t pd 0.51 0.61 ns nor2 y = !(a + b) t pd 0.51 0.61 ns xor2 y = a bt pd 0.78 0.92 ns maj3 y = maj(a , b, c) t pd 0.74 0.87 ns xor3 y = a b ct pd 0.93 1.09 ns mux2 y = a !s + b s t pd 0.54 0.63 ns and3 y = a b c t pd 0.59 0.70 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-106 v1.0 table 2-173 ? combinatorial cell propagation delays military-case conditions: t j = 125c, worst-case v cc = 1.425 v for A3P1000 combinatorial cell equation parameter ?1 std. units inv y = !a t pd 0.48 0.57 ns and2 y = a b t pd 0.57 0.67 ns nand2 y = !(a b) t pd 0.57 0.67 ns or2 y = a + b t pd 0.59 0.69 ns nor2 y = !(a + b) t pd 0.59 0.69 ns xor2 y = a bt pd 0.89 1.04 ns maj3 y = maj(a , b, c) t pd 0.84 0.99 ns xor3 y = a b ct pd 1.05 1.24 ns mux2 y = a !s + b s t pd 0.61 0.72 ns and3 y = a b c t pd 0.68 0.79 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-107 versatile specifications as a sequential module the military proasic3 library offers a wide variety of sequential cells, including flip-flops and latches. each has a data input and optional enab le, clear, or preset. in this section, timing characteristics are presented for a representative sample from the library. for more details, refer to the igloo, fusion, and proasi c3 macro library guide . figure 2-38 ? sample of sequential cells dq dfn1 data clk out d q dfn1c1 data clk out clr dq dfi1e1p1 data clk out en pre d q dfn1e1 data clk out en www..net
military proasic3/el low-power flash fpgas 2-108 v1.0 figure 2-39 ? timing model and waveforms pre clr out clk data en t sue 50 % 50 % t sud t hd 50 % 50 % t clkq 0 t he t recpre t rempre t recclr t remclr t wclr t wpre t pre2q t clr2q t ckmpwh t ckmpwl 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % 50 % www..net
military proasic3/el low-power flash fpgas v1.0 2-109 timing characteristics table 2-174 ? register delays military-case conditions: t j = 125c, worst-case v cc = 1.14 v for a3pe600l and a3pe3000l parameter description ?1 std. units t clkq clock-to-q of the core register 0.76 0.90 ns t sud data setup time for the core register 0.59 0.70 ns t hd data hold time for the core register 0.00 0.00 ns t sue enable setup time for the core register 0.63 0.74 ns t he enable hold time for th e core register 0.00 0.00 ns t clr2q asynchronous clear-to-q of the core register 0.55 0.65 ns t pre2q asynchronous preset-to-q of the core register 0.55 0.65 ns t remclr asynchronous clear removal time for the core register 0.00 0.00 ns t recclr asynchronous clear reco very time for the core register 0.31 0.36 ns t rempre asynchronous preset removal time for the core register 0.00 0.00 ns t recpre asynchronous preset recovery time for the core register 0.31 0.36 ns t wclr asynchronous clear mini mum pulse width for the core register 0.30 0.34 ns t wpre asynchronous preset minimum pulse wi dth for the core register 0.30 0.34 ns t ckmpwh clock minimum pulse width high for the core register 0.56 0.64 ns t ckmpwl clock minimum pulse width low for the core register 0.56 0.64 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-110 v1.0 table 2-175 ? register delays military-case conditions: t j = 125c, v cc = 1.425 v for a3pe600l and a3pe3000l parameter description ?1 std. units t clkq clock-to-q of the core register 0.58 0.69 ns t sud data setup time for the core register 0.45 0.53 ns t hd data hold time for the core register 0.00 0.00 ns t sue enable setup time for the core register 0.48 0.57 ns t he enable hold time for th e core register 0.00 0.00 ns t clr2q asynchronous clear-to-q of the core register 0.42 0.50 ns t pre2q asynchronous preset-to-q of the core register 0.42 0.50 ns t remclr asynchronous clear removal time for the core register 0.00 0.00 ns t recclr asynchronous clear reco very time for the core register 0.24 0.28 ns t rempre asynchronous preset removal time for the core register 0.00 0.00 ns t recpre asynchronous preset recovery time for the core register 0.24 0.28 ns t wclr asynchronous clear mini mum pulse width for the core register 0.30 0.34 ns t wpre asynchronous preset minimum pulse wi dth for the core register 0.30 0.34 ns t ckmpwh clock minimum pulse width high for the core register 0.56 0.64 ns t ckmpwl clock minimum pulse width low for the core register 0.56 0.64 ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-111 table 2-176 ? register delays military-case conditions: t j = 125c, worst-case v cc = 1.425 v for A3P1000 parameter description ?1 std. units t clkq clock-to-q of the core register 0.66 0.78 ns t sud data setup time for the core register 0.52 0.61 ns t hd data hold time for the core register 0.00 0.00 ns t sue enable setup time for the core register 0.55 0.64 ns t he enable hold time for th e core register 0.00 0.00 ns t clr2q asynchronous clear-to-q of the core register 0.48 0.56 ns t pre2q asynchronous preset-to-q of the core register 0.48 0.56 ns t remclr asynchronous clear removal time for the core register 0.00 0.00 ns t recclr asynchronous clear reco very time for the core register 0.27 0.31 ns t rempre asynchronous preset removal time for the core register 0.00 0.00 ns t recpre asynchronous preset recovery time for the core register 0.27 0.31 ns t wclr asynchronous clear mini mum pulse width for the core register 0.25 0.30 ns t wpre asynchronous preset minimum pulse wi dth for the core register 0.25 0.30 ns t ckmpwh clock minimum pulse width high for the core register 0.41 0.48 ns t ckmpwl clock minimum pulse width low for the core register 0.37 0.43 ns note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-112 v1.0 global resource characteristics A3P1000 clock tree topology clock delays are device-specific. figure 2-40 is an example of a global tree used for clock routing. the global tree presented in figure 2-40 is driven by a ccc located on the west side of the A3P1000 device. it is used to drive al l d-flip-flops in the device. figure 2-40 ? example of global tree use in an A3P1000 device for clock routing central global rib versatile rows global spine ccc www..net
military proasic3/el low-power flash fpgas v1.0 2-113 global tree timing characteristics global clock delays include the central rib delay, the spine delay, and the row delay. delays do not include i/o input buffer clock delays, as these are i/o standard?dependent, and the clock may be driven and conditioned internally by the ccc module. for more details on clock conditioning capabilities, refer to the "clock conditioning circuits" section on page 2-116 . table 2-177 to table 2-181 on page 2-115 present minimum and maxi mum global clock delays within each device. minimum and maximum delays are measur ed with minimum an d maximum loading. timing characteristics 1.2 v dc core voltage table 2-177 ? a3pe600l global resource military-case conditions: t j = 125c, v cc = 1.14 v parameter description ?1 std. units min. 1 max. 2 min. 1 max. 2 t rckl input low delay for global clock ns t rckh input high delay fo r global clock ns t rckmpwh minimum pulse width high for global clock ns t rckmpwl minimum pulse width lo w for global clock ns t rcksw maximum skew for global clock ns f rmax maximum frequency for global clock mhz notes: 1. value reflects minimum lo ad. the delay is measured from the ccc output to the clock pin of a sequential element, located in a lightly loaded row (single element is co nnected to the global net). 2. value reflects maximum load. the delay is measur ed on the clock pin of the farthest sequential element, located in a fu lly loaded row (all available flip-flops are connected to the global net in the row). 3. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-178 ? a3pe3000l global resource military-case conditions: t j = 125c, v cc = 1.14 v parameter description ?1 std. units min. 1 max. 2 min. 1 max. 2 t rckl input low delay for global clock 1.80 2.06 2.12 2.42 ns t rckh input high delay for global clock 1.79 2.09 2.11 2.45 ns t rckmpwh minimum pulse width high for global clock ns t rckmpwl minimum pulse width lo w for global clock ns t rcksw maximum skew for glob al clock 0.30 0.35 ns f rmax maximum frequency for global clock mhz notes: 1. value reflects minimum lo ad. the delay is measured from the ccc output to the clock pin of a sequential element, located in a lightly loaded row (single element is co nnected to the global net). 2. value reflects maximum load. the delay is measur ed on the clock pin of the farthest sequential element, located in a fu lly loaded row (all available flip-flops are connected to the global net in the row). 3. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-114 v1.0 1.5 v dc core voltage table 2-179 ? a3pe600l global resource military-case conditions: t j = 125c, v cc = 1.425 v parameter description ?1 std. units min. 1 max. 2 min. 1 max. 2 t rckl input low delay for global clock ns t rckh input high delay fo r global clock ns t rckmpwh minimum pulse width high for global clock ns t rckmpwl minimum pulse width lo w for global clock ns t rcksw maximum skew for global clock ns f rmax maximum frequency for global clock mhz notes: 1. value reflects minimum lo ad. the delay is measured from the ccc output to the clock pin of a sequential element, located in a lightly loaded row (single element is co nnected to the global net). 2. value reflects maximum load. the delay is measur ed on the clock pin of the farthest sequential element, located in a fu lly loaded row (all available flip-flops are connected to the global net in the row). 3. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-180 ? A3P1000 global resource military-case conditions: t j = 125c, v cc = 1.425 v parameter description ?1 std. units min. 1 max. 2 min. 1 max. 2 t rckl input low delay for global clock 1.18 1.44 1.39 1.70 ns t rckh input high delay for global clock 1.17 1.48 1.37 1.74 ns t rckmpwh minimum pulse width high for global clock ns t rckmpwl minimum pulse width lo w for global clock ns t rcksw maximum skew for glob al clock 0.32 0.37 ns f rmax maximum frequency for global clock mhz notes: 1. value reflects minimum lo ad. the delay is measured from the ccc output to the clock pin of a sequential element, located in a lightly loaded row (single element is co nnected to the global net). 2. value reflects maximum load. the delay is measur ed on the clock pin of the farthest sequential element, located in a fu lly loaded row (all available flip-flops are connected to the global net in the row). 3. for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-115 table 2-181 ? a3pe3000l global resource military-case conditions: t j = 125c, v cc = 1.425 v parameter description ?1 std. units min. 1 max. 2 min. 1 max. 2 t rckl input low delay for global clock 1.61 1.85 1.89 2.17 ns t rckh input high delay for global clock 1.60 1.87 1.88 2.20 ns t rckmpwh minimum pulse width high for global clock ns t rckmpwl minimum pulse width lo w for global clock ns t rcksw maximum skew for glob al clock 0.27 0.32 ns f rmax maximum frequency for global clock mhz notes: 1. value reflects minimum lo ad. the delay is measured from the ccc output to the clock pin of a sequential element, located in a lightly loaded row (single element is co nnected to the global net). 2. value reflects maximum load. the delay is measur ed on the clock pin of the farthest sequential element, located in a fu lly loaded row (all available flip-flops are connected to the global net in the row). 3. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-116 v1.0 clock conditioning circuits ccc electrical specifications timing characteristics table 2-182 ? military proasic3/el ccc/pll specification for devices operating at 1.2 v dc core voltage: applicable to a3pe600l and a3pe3000l only parameter min. typ. max. units clock conditioning circuitry input frequency f in_ccc 1.5 250 mhz clock conditioning circuitry output frequency f out_ccc 0.75 250 mhz delay increments in programmable delay blocks 1, 2 270 ps number of programmable values in each programmable delay block 32 serial clock (sclk) for dynamic pll 3 100 mhz input cycle-to-cycle jitter (peak magnitude) 1 ns ccc output peak-to-p eak period jitter f ccc_out max peak-to-peak period jitter 1 global network used external fb used 3 global networks used 0.75 mhz to 24 mhz 0.50 % 0.75 % 0.70 % 24 mhz to 100 mhz 1.00 % 1.50 % 1.20 % 100 mhz to 250 mhz 2.50 % 3.75 % 2.75 % acquisition time lockcontrol = 0 300 s lockcontrol = 1 6.0 ms tracking jitter lockcontrol = 0 2 ns lockcontrol = 1 1 ns output duty cycle 48.5 51.5 % delay range in block: programmable delay 1 1, 2 1.2 15.65 ns delay range in block: programmable delay 2 1, 2 0.025 15.65 ns delay range in block: fixed delay 1, 2 3.1 ns notes: 1. this delay is a function of voltage and temperature. see table 2-5 on page 2-8 for deratings. 2. t j = 25c, v cc = 1.2 v 3. maximum value obtained for a std. speed grade device in worst-case military conditions. for specific junction temperature and volt age supply levels, refer to table 2-5 on page 2-8 for derating values. 4. tracking jitter is defined as the variation in clock ed ge position of pll outputs with reference to pll input clock edge. tracking jitter does not measure the variat ion in pll output period, which is covered by period jitter parameter. www..net
military proasic3/el low-power flash fpgas v1.0 2-117 table 2-183 ? military proasic3/el ccc/pll specification for devices operating at 1.5 v dc core voltage parameter min. typ. max. units clock conditioning circuitry input frequency f in_ccc 1.5 350 mhz clock conditioning circuitry output frequency f out_ccc 0.75 350 mhz serial clock (sclk) for dynamic pll 5 110 mhz delay increments in programmable delay blocks 1, 2 200 ps number of programmable values in each programmable delay block 32 input period jitter 1.5 ns ccc output peak-to-p eak period jitter f ccc_out max peak-to-peak period jitter 1 global network used 3 global networks used 0.75 mhz to 24 mhz 0.50 % 0.70 % 24 mhz to 100 mhz 1.00 % 1.20 % 100 mhz to 250 mhz 1.75 % 2.00 % 250 mhz to 350 mhz 2.50 % 5.60 % acquisition time lockcontrol = 0 300 s lockcontrol = 1 6.0 ms tracking jitter lockcontrol = 0 1.6 ns lockcontrol = 1 0.8 ns output duty cycle 48.5 51.5 % delay range in block: programmable delay 1 1, 2 0.6 5.56 ns delay range in block: programmable delay 2 1, 2 0.025 5.56 ns delay range in block: fixed delay 1, 2 2.2 ns notes: 1. this delay is a function of voltage and temperature. see table 2-5 on page 2-8 for deratings. 2. t j = 25c, v cc = 1.5 v 3. maximum value obtained for a std. speed grade device in worst-case military conditions. for specific junction temperature and volt age supply levels, refer to table 2-5 on page 2-8 for derating values. 4. tracking jitter is defined as the variation in clock ed ge position of pll outputs with reference to pll input clock edge. tracking jitter does not measure the variat ion in pll output period, which is covered by period jitter parameter. 5. maximum value obtained for a -1 speed grade device in worst-case military condit ions. for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-118 v1.0 note: peak-to-peak jitter measurements are defined by t peak-to-peak = t period_max ? t period_min . figure 2-41 ? peak-to-peak jitter definition t perio d _max t perio d _min output s i g nal www..net
military proasic3/el low-power flash fpgas v1.0 2-119 embedded sram and fifo characteristics sram figure 2-42 ? ram models addra11 douta8 douta7 douta0 doutb8 doutb7 doutb0 addra10 addra0 dina8 dina7 dina0 widtha1 widtha0 pipea wmodea blka wena clka addrb11 addrb10 addrb0 dinb8 dinb7 dinb0 widthb1 widthb0 pipeb wmodeb blkb wenb clkb ram4k9 raddr8 rd17 raddr7 rd16 raddr0 rd0 wd17 wd16 wd0 ww1 ww0 rw1 rw0 pipe ren rclk ram512x18 waddr8 waddr7 waddr0 wen wclk reset reset www..net
military proasic3/el low-power flash fpgas 2-120 v1.0 timing waveforms figure 2-43 ? ram read for pass-through output figure 2-44 ? ram read for pipelined output clk add blk_b wen_b do a 0 a 1 a 2 d 0 d 1 d 2 t cyc t ckh t ckl t as t ah t bks t ens t enh t doh1 t bkh d n t ckq1 clk add blk_b wen_b do a 0 a 1 a 2 d 0 d 1 t cyc t ckh t ckl t as t ah t bks t ens t enh t doh2 t ckq2 t bkh d n www..net
military proasic3/el low-power flash fpgas v1.0 2-121 figure 2-45 ? ram write, output retained (wmode = 0) figure 2-46 ? ram write, output as write data (wmode = 1) t cyc t ckh t ckl a 0 a 1 a 2 di 0 di 1 t as t ah t bks t ens t enh t ds t dh clk blk_b wen_b add di d n do t bkh d 2 t cyc t ckh t ckl a 0 a 1 a 2 di 0 di 1 t as t ah t bks t ens t ds t dh clk blk_b wen_b add di t bkh do (pass-through) di 1 d n di 0 do (pipelined) di 0 di 1 d n di 2 www..net
military proasic3/el low-power flash fpgas 2-122 v1.0 figure 2-47 ? write access after write onto same address c lk1 c lk2 wen_b1 wen_b2 add1 add2 di1 di2 do2 (pass-throu g h) do2 (pipeline d ) a 0 t ah t a s t ah t a s t dh t cc kh t d s t c kq1 t c kq2 d 1 a 1 d 2 a 3 d 3 a 0 d 0 d n d 0 d n d 0 a 0 a 4 d 4 www..net
military proasic3/el low-power flash fpgas v1.0 2-123 figure 2-48 ? read access after write onto same address c lk1 c lk2 wen_b1 wen_b2 add1 add2 di1 do2 (pass-throu g h) do2 (pipeline d ) a 0 t ah t a s t ah t a s t dh t d s t wro t c kq1 t c kq2 d 0 a 0 a 1 a 4 d n d n d 0 d 0 d 1 a 2 d 2 a 3 d 3 www..net
military proasic3/el low-power flash fpgas 2-124 v1.0 figure 2-49 ? write access after read onto same address figure 2-50 ? ram reset a 0 a 1 a 0 a 0 a 1 a 3 d 1 d 2 d 3 t ah t a s t ah t a s t c kq1 t c kq1 t c kq2 t cc kh c lk1 add1 wen_b1 do1 ( pass-throu g h) do1 (pipeline d ) c lk2 add2 di2 wen_b2 d n d n d 0 d 1 d 0 clk reset_b do d n t cyc t ckh t ckl t rstbq d m www..net
military proasic3/el low-power flash fpgas v1.0 2-125 timing characteristics table 2-184 ? ram4k9 military-case conditions: t j = 125c, worst-case v cc = 1.14 v for a3pe600l and a3pe3000l parameter description ?1 std. units t as address setup time 0.35 0.41 ns t ah address hold time 0.00 0.00 ns t ens ren_b, wen_b setup time 0.20 0.23 ns t enh ren_b, wen_b hold time 0.13 0.16 ns t bks blk_b setup time 0.32 0.38 ns t bkh blk_b hold time 0.03 0.03 ns t ds input data (di) setup time 0.25 0.30 ns t dh input data (di) hold time 0.00 0.00 ns t ckq1 clock high to new data valid on do (output retained, wmode = 0) 2.47 2.91 ns clock high to new data valid on do (flow-through, wmode = 1) 3.26 3.84 ns t ckq2 clock high to new data valid on do (pipelined) 1.24 1.46 ns t wro address collision clk-to-clk delay for re liable read access after write on same address tbd tbd ns t cckh address collision clk-to-clk delay for re liable write access after write/read on same address tbd tbd ns t rstbq reset_b low to data out low on do (flow-through) 1.28 1.50 ns reset_b low to data out low on do (pipelined) 1.28 1.50 ns t remrstb reset_b removal 0.40 0.47 ns t recrstb reset_b recovery 2.08 2.44 ns t mpwrstb reset_b minimum pulse width 0.66 0.76 ns t cyc clock cycle time 6.08 6.99 ns f max maximum frequency 164 143 mhz note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-126 v1.0 table 2-185 ? ram4k9 military-case conditions: t j = 125c, v cc = 1.425 v for a3pe600l and a3pe3000l parameter description ?1 std. units t as address setup time 0.26 0.31 ns t ah address hold time 0.00 0.00 ns t ens ren_b, wen_b setup time 0.15 0.18 ns t enh ren_b, wen_b hold time 0.10 0.12 ns t bks blk_b setup time 0.25 0.29 ns t bkh blk_b hold time 0.02 0.02 ns t ds input data (di) setup time 0.19 0.23 ns t dh input data (di) hold time 0.00 0.00 ns t ckq1 clock high to new data valid on do (output retained, wmode = 0) 1.89 2.22 ns clock high to new data valid on do (flow-through, wmode = 1) 2.50 2.93 ns t ckq2 clock high to new data valid on do (pipelined) 0.95 1.11 ns t wro address collision clk-to-clk delay for re liable read access after write on same address tbd tbd ns t cckh address collision clk-to-clk delay for re liable write access after write/read on same address tbd tbd ns t rstbq reset_b low to data out low on do (flow-through) 0.98 1.15 ns reset_b low to data out low on do (pipelined) 0.98 1.15 ns t remrstb reset_b removal 0.30 0.36 ns t recrstb reset_b recovery 1.59 1.87 ns t mpwrstb reset_b minimum pulse width 0.59 0.67 ns t cyc clock cycle time 5.39 6.20 ns f max maximum frequency 185 161 mhz note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-127 table 2-186 ? ram4k9 military-case conditions: t j = 125c, worst-case v cc = 1.425 v for A3P1000 parameter description ?1 std. units t as address setup time 0.30 0.35 ns t ah address hold time 0.00 0.00 ns t ens ren_b, wen_b setup time 0.17 0.20 ns t enh ren_b, wen_b hold time 0.12 0.14 ns t bks blk_b setup time 0.28 0.33 ns t bkh blk_b hold time 0.02 0.03 ns t ds input data (di) setup time 0.22 0.26 ns t dh input data (di) hold time 0.00 0.00 ns t ckq1 clock high to new data valid on do (output retained, wmode = 0) 2.15 2.53 ns clock high to new data valid on do (flow-through, wmode = 1) 2.84 3.33 ns t ckq2 clock high to new data valid on do (pipelined) 1.08 1.27 ns t wro address collision clk-to-clk delay for re liable read access after write on same address tbd tbd ns t cckh address collision clk-to-clk delay for re liable write access after write/read on same address tbd tbd ns t rstbq reset_b low to data out low on do (flow-through) 1.11 1.31 ns reset_b low to data out low on do (pipelined) 1.11 1.31 ns t remrstb reset_b removal 0.34 0.40 ns t recrstb reset_b recovery 1.81 2.12 ns t mpwrstb reset_b minimum pulse width 0.26 0.30 ns t cyc clock cycle time 3.89 4.57 ns f max maximum frequency 257 219 mhz note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-128 v1.0 table 2-187 ? ram512x18 military-case conditions: t j = 125c, worst-case v cc = 1.14 v for a3pe600l and a3pe3000l parameter description ?1 std. units t as address setup time 0.35 0.41 ns t ah address hold time 0.00 0.00 ns t ens ren_b, wen_b setup time 0.13 0.15 ns t enh ren_b, wen_b hold time 0.08 0.09 ns t ds input data (di) setup time 0.25 0.30 ns t dh input data (di) hold time 0.00 0.00 ns t ckq1 clock high to new data valid on do (output retained, wm ode = 0) 2.99 3.52 ns t ckq2 clock high to new data valid on do (pipelined) 1.24 1.46 ns t wro address collision clk-to-clk delay for re liable read access after write on same address tbd tbd ns t cckh address collision clk-to-clk delay for re liable write access after write/read on same address tbd tbd ns t rstbq reset_b low to data out low on do (flow through) 1.28 1.50 ns reset_b low to data out low on do (pipelined) 1.28 1.50 ns t remrstb reset_b removal 0.40 0.47 ns t recrstb reset_b recovery 2.08 2.44 ns t mpwrstb reset_b minimum pulse width 0.66 0.76 ns t cyc clock cycle time 6.08 6.99 ns f max maximum frequency 164 143 mhz note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-129 table 2-188 ? ram512x18 military-case conditions: t j = 125c, v cc = 1.425 v for a3pe600l and a3pe3000l parameter description ?1 std. units t as address setup time 0.26 0.31 ns t ah address hold time 0.00 0.00 ns t ens ren_b, wen_b setup time 0.10 0.11 ns t enh ren_b, wen_b hold time 0.06 0.07 ns t ds input data (di) setup time 0.19 0.23 ns t dh input data (di) hold time 0.00 0.00 ns t ckq1 clock high to new data valid on do (output retained, wm ode = 0) 2.29 2.69 ns t ckq2 clock high to new data valid on do (pipelined) 0.95 1.12 ns t wro address collision clk-to-clk delay for re liable read access after write on same address tbd tbd ns t cckh address collision clk-to-clk delay for re liable write access after write/read on same address tbd tbd ns t rstbq reset_b low to data out low on do (flow through) 0.98 1.15 ns reset_b low to data out low on do (pipelined) 0.98 1.15 ns t remrstb reset_b removal 0.30 0.36 ns t recrstb reset_b recovery 1.59 1.87 ns t mpwrstb reset_b minimum pulse width 0.59 0.67 ns t cyc clock cycle time 5.39 6.20 ns f max maximum frequency 185 161 mhz note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-130 v1.0 table 2-189 ? ram512x18 military-case conditions: t j = 125c, worst-case v cc = 1.425 v for A3P1000 parameter description ?1 std. units t as address setup time 0.30 0.35 ns t ah address hold time 0.00 0.00 ns t ens ren_b, wen_b setup time 0.11 0.13 ns t enh ren_b, wen_b hold time 0.07 0.08 ns t ds input data (di) setup time 0.22 0.26 ns t dh input data (di) hold time 0.00 0.00 ns t ckq1 clock high to new data valid on do (output retained, wm ode = 0) 2.60 3.06 ns t ckq2 clock high to new data valid on do (pipelined) 1.08 1.27 ns t wro address collision clk-to-clk delay for re liable read access after write on same address tbd tbd ns t cckh address collision clk-to-clk delay for re liable write access after write/read on same address tbd tbd ns t rstbq reset_b low to data out low on do (flow through) 1.11 1.31 ns reset_b low to data out low on do (pipelined) 1.11 1.31 ns t remrstb reset_b removal 0.34 0.40 ns t recrstb reset_b recovery 1.81 2.12 ns t mpwrstb reset_b minimum pulse width 0.26 0.30 ns t cyc clock cycle time 3.89 4.57 ns f max maximum frequency 257 219 mhz note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-131 fifo figure 2-51 ? fifo model fifo4k18 rw2 rd17 rw1 rd16 rw0 ww2 ww1 ww0 rd0 estop fstop full afull empty afval11 aempty afval10 afval0 aeval11 aeval10 aeval0 ren rblk rclk wen wblk wclk rpipe wd17 wd16 wd0 reset www..net
military proasic3/el low-power flash fpgas 2-132 v1.0 timing waveforms figure 2-52 ? fifo reset figure 2-53 ? fifo empty flag and aempty flag assertion match (a 0 ) t mpwrstb t rstfg t rstck t rstaf rclk/ wclk reset_b empty aempty wa/ra (address counter) t rstfg t rstaf full afull rclk no match no match dist = aef_th match (empty) t ckaf t rckef empty aempty t cyc wa/ra (address counter) www..net
military proasic3/el low-power flash fpgas v1.0 2-133 figure 2-54 ? fifo full flag and afull flag assertion figure 2-55 ? fifo empty flag and ae mpty flag deassertion figure 2-56 ? fifo full flag and afull flag deassertion no match no match dist = aff_th match (full) t ckaf t wckff t cyc wclk full afull wa/ra (address counter) wclk wa/ra (address counter) match (empty) no match no match no match dist = aef_th + 1 no match rclk empty 1st rising edge after 1st write 2nd rising edge after 1st write t rckef t ckaf aempty dist = aff_th ? 1 match (full) no match no match no match no match t wckf t ckaf 1st rising edge after 1st read 1st rising edge after 2nd read rclk wa/ra (address counter) wclk full afull www..net
military proasic3/el low-power flash fpgas 2-134 v1.0 timing characteristics table 2-190 ? fifo worst military-cas e conditions: t j = 125c, v cc = 1.14 v for a3pe600l and a3pe3000l parameter description ?1 std. units t ens ren_b, wen_b setup time 1.91 2.24 ns t enh ren_b, wen_b hold time 0.03 0.03 ns t bks blk_b setup time 0.40 0.47 ns t bkh blk_b hold time 0.00 0.00 ns t ds input data (di) se tup time 0.25 0.30 ns t dh input data (di) ho ld time 0.00 0.00 ns t ckq1 clock high to new data valid on do (flow-through) 3.26 3.84 ns t ckq2 clock high to new data valid on do (pipelined) 1.24 1.46 ns t rckef rclk high to empty fl ag valid 2.38 2.80 ns t wckff wclk high to full flag valid 2.26 2.66 ns t ckaf clock high to almo st empty/full flag valid 8.57 10.08 ns t rstfg reset_b low to empty/fu ll flag valid 2.34 2.76 ns t rstaf reset_b low to almost empty/full flag valid 8.48 9.97 ns t rstbq reset_b low to data out low on do (flow-through) 1.28 1.50 ns reset_b low to data out low on do (pipelined) 1.28 1.50 ns t remrstb reset_b removal 0.40 0.47 ns t recrstb reset_b recovery 2.08 2.44 ns t mpwrstb reset_b minimum pulse width 0.66 0.76 ns t cyc clock cycle time 6.08 6.99 ns f max maximum frequency for fifo 164 143 mhz note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-135 table 2-191 ? fifo worst military-cas e conditions: t j = 125c, v cc = 1.425 v for a3pe600l and a3pe3000l parameter description ?1 std. units t ens ren_b, wen_b setup time 1.46 1.71 ns t enh ren_b, wen_b hold time 0.02 0.02 ns t bks blk_b setup time 0.40 0.47 ns t bkh blk_b hold time 0.00 0.00 ns t ds input data (di) se tup time 0.19 0.23 ns t dh input data (di) ho ld time 0.00 0.00 ns t ckq1 clock high to new data valid on do (flow-through) 2.50 2.93 ns t ckq2 clock high to new data valid on do (pipelined) 0.95 1.11 ns t rckef rclk high to empty fl ag valid 1.82 2.14 ns t wckff wclk high to full flag valid 1.73 2.03 ns t ckaf clock high to almost empty/full flag valid 6.56 7.71 ns t rstfg reset_b low to empty/fu ll flag valid 1.79 2.11 ns t rstaf reset_b low to almost empty/full flag valid 6.49 7.63 ns t rstbq reset_b low to data out low on do (flow-through) 0.98 1.15 ns reset_b low to data out low on do (pipelined) 0.98 1.15 ns t remrstb reset_b removal 0.30 0.36 ns t recrstb reset_b recovery 1.59 1.87 ns t mpwrstb reset_b minimum pulse width 0.59 0.67 ns t cyc clock cycle time 5.39 6.20 ns f max maximum frequency for fifo 185 161 mhz note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-136 v1.0 table 2-192 ? fifo worst military-cas e conditions: t j = 125c, v cc = 1.425 v for A3P1000 parameter description ?1 std. units t ens ren_b, wen_b setup time 1.66 1.95 ns t enh ren_b, wen_b hold time 0.02 0.03 ns t bks blk_b setup time 0.40 0.47 ns t bkh blk_b hold time 0.00 0.00 ns t ds input data (di) se tup time 0.22 0.26 ns t dh input data (di) ho ld time 0.00 0.00 ns t ckq1 clock high to new data valid on do (flow-through) 2.84 3.33 ns t ckq2 clock high to new data valid on do (pipelined) 1.08 1.27 ns t rckef rclk high to empty fl ag valid 2.07 2.43 ns t wckff wclk high to full flag valid 1.96 2.31 ns t ckaf clock high to almost empty/full flag valid 7.45 8.76 ns t rstfg reset_b low to empty/fu ll flag valid 2.04 2.40 ns t rstaf reset_b low to almost empty/full flag valid 7.38 8.67 ns t rstbq reset_b low to data out low on do (flow-through) 1.11 1.31 ns reset_b low to data out low on do (pipelined) 1.11 1.31 ns t remrstb reset_b removal 0.34 0.40 ns t recrstb reset_b recovery 1.81 2.12 ns t mpwrstb reset_b minimum pulse width 0.26 0.30 ns t cyc clock cycle time 3.89 4.57 ns f max maximum frequency for fifo 257 219 mhz note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-137 embedded flashrom characteristics timing characteristics figure 2-57 ? timing diagram a 0 a 1 t s u t hold t s u t hold t s u t hold t c kq2 t c kq2 t c kq2 c lk a dd ress data d 0 d 0 d 1 table 2-193 ? embedded flashrom access time military-case conditions: t j = 125c, worst-case v cc = 1.14 v for a3pe600l and a3pe3000l parameter description ?1 std. units t su address setup time 0.74 0.87 ns t hold address hold time 0.00 0.00 ns t ck2q clock to out 22.47 26.42 ns f max maximum clock frequency 15 15 mhz note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-194 ? embedded flashrom access time military-case conditions: t j = 125c, v cc = 1.425 v for a3pe600l and a3pe3000l parameter description ?1 std. units t su address setup time 0.56 0.66 ns t hold address hold time 0.00 0.00 ns t ck2q clock to out 17.19 20.21 ns f max maximum clock frequency 15 15 mhz note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-195 ? embedded flashrom access time military-case conditions: t j = 125c, worst-case v cc = 1.425 v for A3P1000 parameter description ?1 std. units t su address setup time 0.64 0.75 ns t hold address hold time 0.00 0.00 ns t ck2q clock to out 19.54 22.97 ns f max maximum clock frequency 15 15 mhz note: for specific junction temperature and voltage supply levels, refer to table 2-6 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas 2-138 v1.0 jtag 1532 characteristics jtag timing delays do not include jtag i/os. to obtain complete jtag timing, add i/o buffer delays to the corresponding standard selected; refer to the i/o timing ch aracteristics in the "user i/o characteristics" section on page 2-20 for more details. timing characteristics part number and revision date part number 51700106-001-0 revised august 2008 table 2-196 ? jtag 1532 military-case conditions: t j = 125c, worst-case v cc = 1.14 v for a3pe600l and a3pe3000l parameter description ?1 std. units t disu test data input setup time 0.80 0.94 ns t dihd test data input hold time 1.60 1.88 ns t tmssu test mode select setup time 0.80 0.94 ns t tmdhd test mode select hold time 1.60 1.88 ns t tck2q clock to q (data out) 6.39 7.52 ns t rstb2q reset to q (data out) 26.63 31.33 ns f tckmax tck maximum frequency 18.70 15.90 mhz t trstrem resetb removal time 0.48 0.56 ns t trstrec resetb recovery time 0.00 0.00 ns t trstmpw resetb minimum pulse tbd tbd ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. table 2-197 ? jtag 1532 military-case conditions: t j = 125c, worst-case v cc = 1.425 v for all dies parameter description ?1 std. units t disu test data input setup time 0.60 0.71 ns t dihd test data input hold time 1.21 1.42 ns t tmssu test mode select setup time 0.60 0.71 ns t tmdhd test mode select hold time 1.21 1.42 ns t tck2q clock to q (data out) 6.04 7.10 ns t rstb2q reset to q (data out) 24.15 28.41 ns f tckmax tck maximum frequency 22.00 19.00 mhz t trstrem resetb removal time 0.00 0.00 ns t trstrec resetb recovery time 0.24 0.28 ns t trstmpw resetb minimum pulse tbd tbd ns note: for specific junction temperature and voltage supply levels, refer to table 2-5 on page 2-8 for derating values. www..net
military proasic3/el low-power flash fpgas v1.0 2-139 actel safety critical, life support, and high-reliability applications policy the actel products described in this advance st atus datasheet may not have completed actel?s qualification process. actel may amend or enhance products during the product introduction and qualification process, resulting in changes in device functional ity or performance. it is the responsibility of each customer to ensure the fitn ess of any actel product (but especially a new product) for a particular purpose, including appr opriateness for safety-cri tical, life-s upport, and other high-reliability applicatio ns. consult actel?s terms and cond itions for specific liability exclusions relating to life-support applications. a reliabilit y report covering all of actel?s products is available on the actel website at http://www.actel.com/documents/ort_report.pdf . actel also offers a variety of enhanced qualification and lot acceptance screening procedures. contact your local actel sales office for addi tional reliability information. www..net
www..net
v1.0 3-1 military proasic3/el packaging 3 ? package pin assignments 208-pin pqfp note for package manufacturing and environmental information, visit the resource center at http://www.actel.com/products/ solutions/pac kage/docs.aspx . note: this is the top view of the package. figure 3-1 ? 208-pin pqfp 1 208 www..net
package pin assignments 3-2 v1.0 208-pin pqfp pin number A3P1000 function 1 gnd 2 gaa2/io225pdb3 3 io225ndb3 4 gab2/io224pdb3 5 io224ndb3 6 gac2/io223pdb3 7 io223ndb3 8 io222pdb3 9 io222ndb3 10 io220pdb3 11 io220ndb3 12 io218pdb3 13 io218ndb3 14 io216pdb3 15 io216ndb3 16 v cc 17 gnd 18 v cci b3 19 io212pdb3 20 io212ndb3 21 gfc1/io209pdb3 22 gfc0/io209ndb3 23 gfb1/io208pdb3 24 gfb0/io208ndb3 25 v complf 26 gfa0/io207npb3 27 v ccplf 28 gfa1/io207ppb3 29 gnd 30 gfa2/io206pdb3 31 io206ndb3 32 gfb2/io205pdb3 33 io205ndb3 34 gfc2/io204pdb3 35 io204ndb3 36 v cc 37 io199pdb3 38 io199ndb3 39 io197psb3 40 v cci b3 41 gnd 42 io191pdb3 43 io191ndb3 44 gec1/io190pdb3 45 gec0/io190ndb3 46 geb1/io189pdb3 47 geb0/io189ndb3 48 gea1/io188pdb3 49 gea0/io188ndb3 50 vmv3 51 gndq 52 gnd 53 vmv2 54 gea2/io187rsb2 55 geb2/io186rsb2 56 gec2/io185rsb2 57 io184rsb2 58 io183rsb2 59 io182rsb2 60 io181rsb2 61 io180rsb2 62 v cci b2 63 io178rsb2 64 io176rsb2 65 gnd 66 io174rsb2 67 io172rsb2 68 io170rsb2 69 io168rsb2 70 io166rsb2 71 v cc 72 v cci b2 208-pin pqfp pin number A3P1000 function 73 io162rsb2 74 io160rsb2 75 io158rsb2 76 io156rsb2 77 io154rsb2 78 io152rsb2 79 io150rsb2 80 io148rsb2 81 gnd 82 io143rsb2 83 io141rsb2 84 io139rsb2 85 io137rsb2 86 io135rsb2 87 io133rsb2 88 v cc 89 v cci b2 90 io128rsb2 91 io126rsb2 92 io124rsb2 93 io122rsb2 94 io120rsb2 95 io118rsb2 96 gdc2/io116rsb2 97 gnd 98 gdb2/io115rsb2 99 gda2/io114rsb2 100 gndq 101 tck 102 tdi 103 tms 104 vmv2 105 gnd 106 v pump 107 gndq 108 tdo 208-pin pqfp pin number a3p1 000 function www..net
military proasic3/el packaging v1.0 3-3 109 trst 110 v jtag 111 gda0/io113ndb1 112 gda1/io113pdb1 113 gdb0/io112ndb1 114 gdb1/io112pdb1 115 gdc0/io111ndb1 116 gdc1/io111pdb1 117 io109ndb1 118 io109pdb1 119 io106ndb1 120 io106pdb1 121 io104psb1 122 gnd 123 v cci b1 124 io99ndb1 125 io99pdb1 126 nc 127 io96ndb1 128 gcc2/io96pdb1 129 gcb2/io95psb1 130 gnd 131 gca2/io94psb1 132 gca1/io93pdb1 133 gca0/io93ndb1 134 gcb0/io92ndb1 135 gcb1/io92pdb1 136 gcc0/io91ndb1 137 gcc1/io91pdb1 138 io88ndb1 139 io88pdb1 140 v cci b1 141 gnd 142 v cc 143 io86psb1 144 io84ndb1 208-pin pqfp pin number A3P1000 function 145 io84pdb1 146 io82ndb1 147 io82pdb1 148 io80ndb1 149 gbc2/io80pdb1 150 io79ndb1 151 gbb2/io79pdb1 152 io78ndb1 153 gba2/io78pdb1 154 vmv1 155 gndq 156 gnd 157 vmv0 158 gba1/io77rsb0 159 gba0/io76rsb0 160 gbb1/io75rsb0 161 gbb0/io74rsb0 162 gnd 163 gbc1/io73rsb0 164 gbc0/io72rsb0 165 io70rsb0 166 io67rsb0 167 io63rsb0 168 io60rsb0 169 io57rsb0 170 v cci b0 171 v cc 172 io54rsb0 173 io51rsb0 174 io48rsb0 175 io45rsb0 176 io42rsb0 177 io40rsb0 178 gnd 179 io38rsb0 180 io35rsb0 208-pin pqfp pin number A3P1000 function 181 io33rsb0 182 io31rsb0 183 io29rsb0 184 io27rsb0 185 io25rsb0 186 v cci b0 187 v cc 188 io22rsb0 189 io20rsb0 190 io18rsb0 191 io16rsb0 192 io15rsb0 193 io14rsb0 194 io13rsb0 195 gnd 196 io12rsb0 197 io11rsb0 198 io10rsb0 199 io09rsb0 200 v cci b0 201 gac1/io05rsb0 202 gac0/io04rsb0 203 gab1/io03rsb0 204 gab0/io02rsb0 205 gaa1/io01rsb0 206 gaa0/io00rsb0 207 gndq 208 vmv0 208-pin pqfp pin number a3p1 000 function www..net
package pin assignments 3-4 v1.0 144-pin fbga note for package manufacturing and environmental information, visit the resource center at http://www.actel.com/products/ solutions/pac kage/docs.aspx . note: this is the bottom view of the package. figure 3-2 ? 1 2 3 4 5 6 7 8 9 10 11 12 a b c d e f g h j k l m a1 ball pad corner www..net
military proasic3/el packaging v1.0 3-5 144-pin fbga pin number A3P1000 function a1 gndq a2 vmv0 a3 gab0/io02rsb0 a4 gab1/io03rsb0 a5 io10rsb0 a6 gnd a7 io44rsb0 a8 v cc a9 io69rsb0 a10 gba0/io76rsb0 a11 gba1/io77rsb0 a12 gndq b1 gab2/io224pdb3 b2 gnd b3 gaa0/io00rsb0 b4 gaa1/io01rsb0 b5 io13rsb0 b6 io26rsb0 b7 io35rsb0 b8 io60rsb0 b9 gbb0/io74rsb0 b10 gbb1/io75rsb0 b11 gnd b12 vmv1 c1 io224ndb3 c2 gfa2/io206ppb3 c3 gac2/io223pdb3 c4 v cc c5 io16rsb0 c6 io29rsb0 c7 io32rsb0 c8 io63rsb0 c9 io66rsb0 c10 gba2/io78pdb1 c11 io78ndb1 c12 gbc2/io80ppb1 d1 io213pdb3 d2 io213ndb3 d3 io223ndb3 d4 gaa2/io225ppb3 d5 gac0/io04rsb0 d6 gac1/io05rsb0 d7 gbc0/io72rsb0 d8 gbc1/io73rsb0 d9 gbb2/io79pdb1 d10 io79ndb1 d11 io80npb1 d12 gcb1/io92ppb1 e1 v cc e2 gfc0/io209ndb3 e3 gfc1/io209pdb3 e4 v cci b3 e5 io225npb3 e6 v cci b0 e7 v cci b0 e8 gcc1/io91pdb1 e9 v cci b1 e10 v cc e11 gca0/io93ndb1 e12 io94ndb1 f1 gfb0/io208npb3 f2 v complf f3 gfb1/io208ppb3 f4 io206npb3 f5 gnd f6 gnd f7 gnd f8 gcc0/io91ndb1 f9 gcb0/io92npb1 f10 gnd f11 gca1/io93pdb1 f12 gca2/io94pdb1 144-pin fbga pin number A3P1000 function g1 gfa1/io207ppb3 g2 gnd g3 v ccplf g4 gfa0/io207npb3 g5 gnd g6 gnd g7 gnd g8 gdc1/io111ppb1 g9 io96ndb1 g10 gcc2/io96pdb1 g11 io95ndb1 g12 gcb2/io95pdb1 h1 v cc h2 gfb2/io205pdb3 h3 gfc2/io204psb3 h4 gec1/io190pdb3 h5 v cc h6 io105pdb1 h7 io105ndb1 h8 gdb2/io115rsb2 h9 gdc0/io111npb1 h10 v cci b1 h11 io101psb1 h12 v cc j1 geb1/io189pdb3 j2 io205ndb3 j3 v cci b3 j4 gec0/io190ndb3 j5 io160rsb2 j6 io157rsb2 j7 v cc j8 tck j9 gda2/io114rsb2 j10 tdo j11 gda1/io113pdb1 j12 gdb1/io112pdb1 144-pin fbga pin number A3P1000 function www..net
package pin assignments 3-6 v1.0 k1 geb0/io189ndb3 k2 gea1/io188pdb3 k3 gea0/io188ndb3 k4 gea2/io187rsb2 k5 io169rsb2 k6 io152rsb2 k7 gnd k8 io117rsb2 k9 gdc2/io116rsb2 k10 gnd k11 gda0/io113ndb1 k12 gdb0/io112ndb1 l1 gnd l2 vmv3 l3 ff/geb2/io186rsb2 l4 io172rsb2 l5 v cci b2 l6 io153rsb2 l7 io144rsb2 l8 io140rsb2 l9 tms l10 v jtag l11 vmv2 l12 trst m1 gndq m2 gec2/io185rsb2 m3 io173rsb2 m4 io168rsb2 m5 io161rsb2 m6 io156rsb2 m7 io145rsb2 m8 io141rsb2 m9 tdi m10 v cci b2 m11 v pump m12 gndq 144-pin fbga pin number A3P1000 function www..net
military proasic3/el packaging v1.0 3-7 484-pin fbga note for package manufacturing and environmental information, visit the resource center at http://www.actel.com/products/ solutions/pac kage/docs.aspx. note: this is the bottom view of the package. figure 3-3 ? a b c d e f g h j k l m n p r t u v w y aa ab 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 a1 ball pad corner www..net
package pin assignments 3-8 v1.0 484-pin fbga pin number a3pe600l function a1 gnd a2 gnd a3 v cci b0 a4 io06ndb0v1 a5 io06pdb0v1 a6 io08ndb0v1 a7 io08pdb0v1 a8 io11pdb0v1 a9 io17pdb0v2 a10 io18ndb0v2 a11 io18pdb0v2 a12 io22pdb1v0 a13 io26pdb1v0 a14 io29ndb1v1 a15 io29pdb1v1 a16 io31ndb1v1 a17 io31pdb1v1 a18 io32ndb1v1 a19 nc a20 v cci b1 a21 gnd a22 gnd b1 gnd b2 v cci b7 b3 nc b4 io03ndb0v0 b5 io03pdb0v0 b6 io07ndb0v1 b7 io07pdb0v1 b8 io11ndb0v1 b9 io17ndb0v2 b10 io14pdb0v2 b11 io19pdb0v2 b12 io22ndb1v0 b13 io26ndb1v0 b14 nc b15 nc b16 io30ndb1v1 b17 io30pdb1v1 b18 io32pdb1v1 b19 nc b20 nc b21 v cci b2 b22 gnd c1 v cci b7 c2 nc c3 nc c4 nc c5 gnd c6 io04ndb0v0 c7 io04pdb0v0 c8 v cc c9 v cc c10 io14ndb0v2 c11 io19ndb0v2 c12 nc c13 nc c14 v cc c15 v cc c16 nc c17 nc c18 gnd c19 nc c20 nc c21 nc c22 v cci b2 d1 nc d2 nc d3 nc d4 gnd 484-pin fbga pin number a3pe600l function d5 gaa0/io00ndb0v0 d6 gaa1/io00pdb0v0 d7 gab0/io01ndb0v0 d8 io05pdb0v0 d9 io10pdb0v1 d10 io12pdb0v2 d11 io16ndb0v2 d12 io23ndb1v0 d13 io23pdb1v0 d14 io28ndb1v1 d15 io28pdb1v1 d16 gbb1/io34pdb1v1 d17 gba0/io35ndb1v1 d18 gba1/io35pdb1v1 d19 gnd d20 nc d21 nc d22 nc e1 nc e2 nc e3 gnd e4 gab2/io133pdb7v1 e5 gaa2/io134pdb7v1 e6 gndq e7 gab1/io01pdb0v0 e8 io05ndb0v0 e9 io10ndb0v1 e10 io12ndb0v2 e11 io16pdb0v2 e12 io20ndb1v0 e13 io24ndb1v0 e14 io24pdb1v0 e15 gbc1/io33pdb1v1 e16 gbb0/io34ndb1v1 e17 gndq 484-pin fbga pin number a3pe600l function www..net
military proasic3/el packaging v1.0 3-9 e18 gba2/io36pdb2v0 e19 io42ndb2v0 e20 gnd e21 nc e22 nc f1 nc f2 io131ndb7v1 f3 io131pdb7v1 f4 io133ndb7v1 f5 io134ndb7v1 f6 vmv7 f7 v ccpla f8 gac0/io02ndb0v0 f9 gac1/io02pdb0v0 f10 io15ndb0v2 f11 io15pdb0v2 f12 io20pdb1v0 f13 io25ndb1v0 f14 io27pdb1v0 f15 gbc0/io33ndb1v1 f16 v ccplb f17 vmv2 f18 io36ndb2v0 f19 io42pdb2v0 f20 nc f21 nc f22 nc g1 io127ndb7v1 g2 io127pdb7v1 g3 nc g4 io128pdb7v1 g5 io129pdb7v1 g6 gac2/io132pdb7v1 g7 v compla g8 gndq 484-pin fbga pin number a3pe600l function g9 io09ndb0v1 g10 io09pdb0v1 g11 io13pdb0v2 g12 io21pdb1v0 g13 io25pdb1v0 g14 io27ndb1v0 g15 gndq g16 v complb g17 gbb2/io37pdb2v0 g18 io39pdb2v0 g19 io39ndb2v0 g20 io43pdb2v0 g21 io43ndb2v0 g22 nc h1 nc h2 nc h3 v cc h4 io128ndb7v1 h5 io129ndb7v1 h6 io132ndb7v1 h7 io130pdb7v1 h8 vmv0 h9 v cci b0 h10 v cci b0 h11 io13ndb0v2 h12 io21ndb1v0 h13 v cci b1 h14 v cci b1 h15 vmv1 h16 gbc2/io38pdb2v0 h17 io37ndb2v0 h18 io41ndb2v0 h19 io41pdb2v0 h20 v cc h21 nc 484-pin fbga pin number a3pe600l function h22 nc j1 io123ndb7v0 j2 io123pdb7v0 j3 nc j4 io124pdb7v0 j5 io125pdb7v0 j6 io126pdb7v0 j7 io130ndb7v1 j8 v cci b7 j9 gnd j10 v cc j11 v cc j12 v cc j13 v cc j14 gnd j15 v cci b2 j16 io38ndb2v0 j17 io40ndb2v0 j18 io40pdb2v0 j19 io45pdb2v1 j20 nc j21 io48pdb2v1 j22 io46pdb2v1 k1 io121ndb7v0 k2 io121pdb7v0 k3 nc k4 io124ndb7v0 k5 io125ndb7v0 k6 io126ndb7v0 k7 gfc1/io120ppb7v0 k8 v cci b7 k9 v cc k10 gnd k11 gnd k12 gnd 484-pin fbga pin number a3pe600l function www..net
package pin assignments 3-10 v1.0 k13 gnd k14 v cc k15 v cci b2 k16 gcc1/io50ppb2v1 k17 io44ndb2v1 k18 io44pdb2v1 k19 io49npb2v1 k20 io45ndb2v1 k21 io48ndb2v1 k22 io46ndb2v1 l1 nc l2 io122pdb7v0 l3 io122ndb7v0 l4 gfb0/io119npb7v0 l5 gfa0/io118ndb6v1 l6 gfb1/io119ppb7v0 l7 v complf l8 gfc0/io120npb7v0 l9 v cc l10 gnd l11 gnd l12 gnd l13 gnd l14 v cc l15 gcc0/io50npb2v1 l16 gcb1/io51ppb2v1 l17 gca0/io52npb3v0 l18 v complc l19 gcb0/io51npb2v1 l20 io49ppb2v1 l21 io47ndb2v1 l22 io47pdb2v1 m1 nc m2 io114ndb6v1 m3 io117ndb6v1 484-pin fbga pin number a3pe600l function m4 gfa2/io117pdb6v1 m5 gfa1/io118pdb6v1 m6 v ccplf m7 io116ndb6v1 m8 gfb2/io116pdb6v1 m9 v cc m10 gnd m11 gnd m12 gnd m13 gnd m14 v cc m15 gcb2/io54ppb3v0 m16 gca1/io52ppb3v0 m17 gcc2/io55ppb3v0 m18 v ccplc m19 gca2/io53pdb3v0 m20 io53ndb3v0 m21 io56pdb3v0 m22 nc n1 io114pdb6v1 n2 io111ndb6v1 n3 nc n4 gfc2/io115pdb6v1 n5 io113ppb6v1 n6 io112pdb6v1 n7 io112ndb6v1 n8 v cci b6 n9 v cc n10 gnd n11 gnd n12 gnd n13 gnd n14 v cc n15 v cci b3 n16 io54npb3v0 484-pin fbga pin number a3pe600l function n17 io57npb3v0 n18 io55npb3v0 n19 io57ppb3v0 n20 nc n21 io56ndb3v0 n22 io58pdb3v0 p1 nc p2 io111pdb6v1 p3 io115ndb6v1 p4 io113npb6v1 p5 io109ppb6v0 p6 io108pdb6v0 p7 io108ndb6v0 p8 v cci b6 p9 gnd p10 v cc p11 v cc p12 v cc p13 v cc p14 gnd p15 v cci b3 p16 gdb0/io66npb3v1 p17 io60ndb3v1 p18 io60pdb3v1 p19 io61pdb3v1 p20 nc p21 io59pdb3v0 p22 io58ndb3v0 r1 nc r2 io110pdb6v0 r3 v cc r4 io109npb6v0 r5 io106ndb6v0 r6 io106pdb6v0 r7 gec0/io104npb6v0 484-pin fbga pin number a3pe600l function www..net
military proasic3/el packaging v1.0 3-11 r8 vmv5 r9 v cci b5 r10 v cci b5 r11 io84ndb5v0 r12 io84pdb5v0 r13 v cci b4 r14 v cci b4 r15 vmv3 r16 v ccpld r17 gdb1/io66ppb3v1 r18 gdc1/io65pdb3v1 r19 io61ndb3v1 r20 v cc r21 io59ndb3v0 r22 io62pdb3v1 t1 nc t2 io110ndb6v0 t3 nc t4 io105pdb6v0 t5 io105ndb6v0 t6 gec1/io104ppb6v0 t7 v comple t8 gndq t9 gea2/io101ppb5v2 t10 io92ndb5v1 t11 io90ndb5v1 t12 io82ndb5v0 t13 io74ndb4v1 t14 io74pdb4v1 t15 gndq t16 v compld t17 v jtag t18 gdc0/io65ndb3v1 t19 gda1/io67pdb3v1 t20 nc 484-pin fbga pin number a3pe600l function t21 io64pdb3v1 t22 io62ndb3v1 u1 nc u2 io107pdb6v0 u3 io107ndb6v0 u4 geb1/io103pdb6v0 u5 geb0/io103ndb6v0 u6 vmv6 u7 v ccple u8 io101npb5v2 u9 io95ppb5v1 u10 io92pdb5v1 u11 io90pdb5v1 u12 io82pdb5v0 u13 io76ndb4v1 u14 io76pdb4v1 u15 vmv4 u16 tck u17 v pump u18 trst u19 gda0/io67ndb3v1 u20 nc u21 io64ndb3v1 u22 io63pdb3v1 v1 nc v2 nc v3 gnd v4 gea1/io102pdb6v0 v5 gea0/io102ndb6v0 v6 gndq v7 gec2/io99pdb5v2 v8 io95npb5v1 v9 io91ndb5v1 v10 io91pdb5v1 v11 io83ndb5v0 484-pin fbga pin number a3pe600l function v12 io83pdb5v0 v13 io77ndb4v1 v14 io77pdb4v1 v15 io69ndb4v0 v16 gdb2/io69pdb4v0 v17 tdi v18 gndq v19 tdo v20 gnd v21 nc v22 io63ndb3v1 w1 nc w2 nc w3 nc w4 gnd w5 io100ndb5v2 w6 geb2/io100pdb5v2 w7 io99ndb5v2 w8 io88ndb5v0 w9 io88pdb5v0 w10 io89ndb5v0 w11 io80ndb4v1 w12 io81ndb4v1 w13 io81pdb4v1 w14 io70ndb4v0 w15 gdc2/io70pdb4v0 w16 io68ndb4v0 w17 gda2/io68pdb4v0 w18 tms w19 gnd w20 nc w21 nc w22 nc y1 v cci b6 y2 nc 484-pin fbga pin number a3pe600l function www..net
package pin assignments 3-12 v1.0 y3 nc y4 io98ndb5v2 y5 gnd y6 io94ndb5v1 y7 io94pdb5v1 y8 v cc y9 v cc y10 io89pdb5v0 y11 io80pdb4v1 y12 io78npb4v1 y13 nc y14 v cc y15 v cc y16 nc y17 nc y18 gnd y19 nc y20 nc y21 nc y22 v cci b3 aa1 gnd aa2 v cci b6 aa3 nc aa4 io98pdb5v2 aa5 io96ndb5v2 aa6 io96pdb5v2 aa7 io86ndb5v0 aa8 io86pdb5v0 aa9 io85pdb5v0 aa10 io85ndb5v0 484-pin fbga pin number a3pe600l function aa11 io78ppb4v1 aa12 io79ndb4v1 aa13 io79pdb4v1 aa14 nc aa15 nc aa16 io71ndb4v0 aa17 io71pdb4v0 aa18 nc aa19 nc aa20 nc aa21 v cci b3 aa22 gnd ab1 gnd ab2 gnd ab3 v cci b5 ab4 io97ndb5v2 ab5 io97pdb5v2 ab6 io93ndb5v1 484-pin fbga pin number a3pe600l function ab7 io93pdb5v1 ab8 io87ndb5v0 ab9 io87pdb5v0 ab10 nc ab11 nc ab12 io75ndb4v1 ab13 io75pdb4v1 ab14 io72ndb4v0 ab15 io72pdb4v0 ab16 io73ndb4v0 ab17 io73pdb4v0 ab18 nc ab19 nc ab20 v cci b4 ab21 gnd ab22 gnd 484-pin fbga pin number a3pe600l function www..net
military proasic3/el packaging v1.0 3-13 484-pin fbga pin number a3pe3000l function a1 gnd a2 gnd a3 v cci b0 a4 io10ndb0v1 a5 io10pdb0v1 a6 io16ndb0v1 a7 io16pdb0v1 a8 io18pdb0v2 a9 io24pdb0v2 a10 io28ndb0v3 a11 io28pdb0v3 a12 io46pdb1v0 a13 io54pdb1v1 a14 io56ndb1v1 a15 io56pdb1v1 a16 io64ndb1v2 a17 io64pdb1v2 a18 io72ndb1v3 a19 io74ndb1v4 a20 v cci b1 a21 gnd a22 gnd aa1 gnd aa2 v cci b6 aa3 io228pdb5v4 aa4 io224pdb5v3 aa5 io218ndb5v3 aa6 io218pdb5v3 aa7 io212ndb5v2 aa8 io212pdb5v2 aa9 io198pdb5v0 aa10 io198ndb5v0 aa11 io188ppb4v4 aa12 io180ndb4v3 aa13 io180pdb4v3 aa14 io170ndb4v2 aa15 io170pdb4v2 aa16 io166ndb4v1 aa17 io166pdb4v1 aa18 io160ndb4v0 aa19 io160pdb4v0 aa20 io158npb4v0 aa21 v cci b3 aa22 gnd ab1 gnd ab2 gnd ab3 v cci b5 ab4 io216ndb5v2 ab5 io216pdb5v2 ab6 io210ndb5v2 ab7 io210pdb5v2 ab8 io208ndb5v1 ab9 io208pdb5v1 ab10 io197ndb5v0 ab11 io197pdb5v0 ab12 io174ndb4v2 ab13 io174pdb4v2 ab14 io172ndb4v2 ab15 io172pdb4v2 ab16 io168ndb4v1 ab17 io168pdb4v1 ab18 io162ndb4v1 ab19 io162pdb4v1 ab20 v cci b4 ab21 gnd ab22 gnd b1 gnd b2 v cci b7 b3 io06ppb0v0 b4 io08ndb0v0 b5 io08pdb0v0 b6 io14ndb0v1 484-pin fbga pin number a3pe3000l function b7 io14pdb0v1 b8 io18ndb0v2 b9 io24ndb0v2 b10 io34pdb0v4 b11 io40pdb0v4 b12 io46ndb1v0 b13 io54ndb1v1 b14 io62ndb1v2 b15 io62pdb1v2 b16 io68ndb1v3 b17 io68pdb1v3 b18 io72pdb1v3 b19 io74pdb1v4 b20 io76npb1v4 b21 v cci b2 b22 gnd c1 v cci b7 c2 io303pdb7v3 c3 io305pdb7v3 c4 io06npb0v0 c5 gnd c6 io12ndb0v1 c7 io12pdb0v1 c8 v cc c9 v cc c10 io34ndb0v4 c11 io40ndb0v4 c12 io48ndb1v0 c13 io48pdb1v0 c14 v cc c15 v cc c16 io70ndb1v3 c17 io70pdb1v3 c18 gnd c19 io76ppb1v4 c20 io88ndb2v0 484-pin fbga pin number a3pe3000l function www..net
package pin assignments 3-14 v1.0 c21 io94ppb2v1 c22 v cci b2 d1 io293pdb7v2 d2 io303ndb7v3 d3 io305ndb7v3 d4 gnd d5 gaa0/io00ndb0v0 d6 gaa1/io00pdb0v0 d7 gab0/io01ndb0v0 d8 io20pdb0v2 d9 io22pdb0v2 d10 io30pdb0v3 d11 io38ndb0v4 d12 io52ndb1v1 d13 io52pdb1v1 d14 io66ndb1v3 d15 io66pdb1v3 d16 gbb1/io80pdb1v4 d17 gba0/io81ndb1v4 d18 gba1/io81pdb1v4 d19 gnd d20 io88pdb2v0 d21 io90pdb2v1 d22 io94npb2v1 e1 io293ndb7v2 e2 io299ppb7v3 e3 gnd e4 gab2/io308pdb7v4 e5 gaa2/io309pdb7v4 e6 gndq e7 gab1/io01pdb0v0 e8 io20ndb0v2 e9 io22ndb0v2 e10 io30ndb0v3 e11 io38pdb0v4 e12 io44ndb1v0 484-pin fbga pin number a3pe3000l function e13 io58ndb1v2 e14 io58pdb1v2 e15 gbc1/io79pdb1v4 e16 gbb0/io80ndb1v4 e17 gndq e18 gba2/io82pdb2v0 e19 io86ndb2v0 e20 gnd e21 io90ndb2v1 e22 io98pdb2v2 f1 io299npb7v3 f2 io301ndb7v3 f3 io301pdb7v3 f4 io308ndb7v4 f5 io309ndb7v4 f6 vmv7 f7 v ccpla f8 gac0/io02ndb0v0 f9 gac1/io02pdb0v0 f10 io32ndb0v3 f11 io32pdb0v3 f12 io44pdb1v0 f13 io50ndb1v1 f14 io60pdb1v2 f15 gbc0/io79ndb1v4 f16 v ccplb f17 vmv2 f18 io82ndb2v0 f19 io86pdb2v0 f20 io96pdb2v1 f21 io96ndb2v1 f22 io98ndb2v2 g1 io289ndb7v1 g2 io289pdb7v1 g3 io291ppb7v2 g4 io295pdb7v2 484-pin fbga pin number a3pe3000l function g5 io297pdb7v2 g6 gac2/io307pdb7v4 g7 v compla g8 gndq g9 io26ndb0v3 g10 io26pdb0v3 g11 io36pdb0v4 g12 io42pdb1v0 g13 io50pdb1v1 g14 io60ndb1v2 g15 gndq g16 v complb g17 gbb2/io83pdb2v0 g18 io92pdb2v1 g19 io92ndb2v1 g20 io102pdb2v2 g21 io102ndb2v2 g22 io105ndb2v2 h1 io286psb7v1 h2 io291npb7v2 h3 v cc h4 io295ndb7v2 h5 io297ndb7v2 h6 io307ndb7v4 h7 io287pdb7v1 h8 vmv0 h9 v cci b0 h10 v cci b0 h11 io36ndb0v4 h12 io42ndb1v0 h13 v cci b1 h14 v cci b1 h15 vmv1 h16 gbc2/io84pdb2v0 h17 io83ndb2v0 h18 io100ndb2v2 484-pin fbga pin number a3pe3000l function www..net
military proasic3/el packaging v1.0 3-15 h19 io100pdb2v2 h20 v cc h21 vmv2 h22 io105pdb2v2 j1 io285ndb7v1 j2 io285pdb7v1 j3 vmv7 j4 io279pdb7v0 j5 io283pdb7v1 j6 io281pdb7v0 j7 io287ndb7v1 j8 v cci b7 j9 gnd j10 v cc j11 v cc j12 v cc j13 v cc j14 gnd j15 v cci b2 j16 io84ndb2v0 j17 io104ndb2v2 j18 io104pdb2v2 j19 io106ppb2v3 j20 gndq j21 io109pdb2v3 j22 io107pdb2v3 k1 io277ndb7v0 k2 io277pdb7v0 k3 gndq k4 io279ndb7v0 k5 io283ndb7v1 k6 io281ndb7v0 k7 gfc1/io275ppb7v0 k8 v cci b7 k9 v cc k10 gnd 484-pin fbga pin number a3pe3000l function k11 gnd k12 gnd k13 gnd k14 v cc k15 v cci b2 k16 gcc1/io112ppb2v3 k17 io108ndb2v3 k18 io108pdb2v3 k19 io110npb2v3 k20 io106npb2v3 k21 io109ndb2v3 k22 io107ndb2v3 l1 io257psb6v2 l2 io276pdb7v0 l3 io276ndb7v0 l4 gfb0/io274npb7v0 l5 gfa0/io273ndb6v4 l6 gfb1/io274ppb7v0 l7 v complf l8 gfc0/io275npb7v0 l9 v cc l10 gnd l11 gnd l12 gnd l13 gnd l14 v cc l15 gcc0/io112npb2v3 l16 gcb1/io113ppb2v3 l17 gca0/io114npb3v0 l18 v complc l19 gcb0/io113npb2v3 l20 io110ppb2v3 l21 io111ndb2v3 l22 io111pdb2v3 m1 gndq m2 io255npb6v2 484-pin fbga pin number a3pe3000l function m3 io272ndb6v4 m4 gfa2/io272pdb6v4 m5 gfa1/io273pdb6v4 m6 v ccplf m7 io271ndb6v4 m8 gfb2/io271pdb6v4 m9 v cc m10 gnd m11 gnd m12 gnd m13 gnd m14 v cc m15 gcb2/io116ppb3v0 m16 gca1/io114ppb3v0 m17 gcc2/io117ppb3v0 m18 v ccplc m19 gca2/io115pdb3v0 m20 io115ndb3v0 m21 io126pdb3v1 m22 io124psb3v1 n1 io255ppb6v2 n2 io253ndb6v2 n3 vmv6 n4 gfc2/io270ppb6v4 n5 io261ppb6v3 n6 io263pdb6v3 n7 io263ndb6v3 n8 v cci b6 n9 v cc n10 gnd n11 gnd n12 gnd n13 gnd n14 v cc n15 v cci b3 n16 io116npb3v0 484-pin fbga pin number a3pe3000l function www..net
package pin assignments 3-16 v1.0 n17 io132npb3v2 n18 io117npb3v0 n19 io132ppb3v2 n20 gndq n21 io126ndb3v1 n22 io128pdb3v1 p1 io247pdb6v1 p2 io253pdb6v2 p3 io270npb6v4 p4 io261npb6v3 p5 io249ppb6v1 p6 io259pdb6v3 p7 io259ndb6v3 p8 v cci b6 p9 gnd p10 v cc p11 v cc p12 v cc p13 v cc p14 gnd p15 v cci b3 p16 gdb0/io152npb3v4 p17 io136ndb3v2 p18 io136pdb3v2 p19 io138pdb3v3 p20 vmv3 p21 io130pdb3v2 p22 io128ndb3v1 r1 io247ndb6v1 r2 io245pdb6v1 r3 v cc r4 io249npb6v1 r5 io251ndb6v2 r6 io251pdb6v2 r7 gec0/io236npb6v0 r8 vmv5 484-pin fbga pin number a3pe3000l function r9 v cci b5 r10 v cci b5 r11 io196ndb5v0 r12 io196pdb5v0 r13 v cci b4 r14 v cci b4 r15 vmv3 r16 v ccpld r17 gdb1/io152ppb3v4 r18 gdc1/io151pdb3v4 r19 io138ndb3v3 r20 v cc r21 io130ndb3v2 r22 io134pdb3v2 t1 io243ppb6v1 t2 io245ndb6v1 t3 io243npb6v1 t4 io241pdb6v0 t5 io241ndb6v0 t6 gec1/io236ppb6v0 t7 v comple t8 gndq t9 gea2/io233ppb5v4 t10 io206ndb5v1 t11 io202ndb5v1 t12 io194ndb5v0 t13 io186ndb4v4 t14 io186pdb4v4 t15 gndq t16 v compld t17 v jtag t18 gdc0/io151ndb3v4 t19 gda1/io153pdb3v4 t20 io144pdb3v3 t21 io140pdb3v3 t22 io134ndb3v2 484-pin fbga pin number a3pe3000l function u1 io240ppb6v0 u2 io238pdb6v0 u3 io238ndb6v0 u4 geb1/io235pdb6v0 u5 geb0/io235ndb6v0 u6 vmv6 u7 v ccple u8 io233npb5v4 u9 io222ppb5v3 u10 io206pdb5v1 u11 io202pdb5v1 u12 io194pdb5v0 u13 io176ndb4v2 u14 io176pdb4v2 u15 vmv4 u16 tck u17 v pump u18 trst u19 gda0/io153ndb3v4 u20 io144ndb3v3 u21 io140ndb3v3 u22 io142pdb3v3 v1 io239pdb6v0 v2 io240npb6v0 v3 gnd v4 gea1/io234pdb6v0 v5 gea0/io234ndb6v0 v6 gndq v7 gec2/io231pdb5v4 v8 io222npb5v3 v9 io204ndb5v1 v10 io204pdb5v1 v11 io195ndb5v0 v12 io195pdb5v0 v13 io178ndb4v3 v14 io178pdb4v3 484-pin fbga pin number a3pe3000l function www..net
military proasic3/el packaging v1.0 3-17 v15 io155ndb4v0 v16 gdb2/io155pdb4v0 v17 tdi v18 gndq v19 tdo v20 gnd v21 io146pdb3v4 v22 io142ndb3v3 w1 io239ndb6v0 w2 io237pdb6v0 w3 io230psb5v4 w4 gnd w5 io232ndb5v4 w6 ff/geb2/io232pdb5 v4 w7 io231ndb5v4 w8 io214ndb5v2 w9 io214pdb5v2 w10 io200ndb5v0 w11 io192ndb4v4 w12 io184ndb4v3 w13 io184pdb4v3 w14 io156ndb4v0 w15 gdc2/io156pdb4v0 w16 io154ndb4v0 w17 gda2/io154pdb4v0 w18 tms w19 gnd w20 io150ndb3v4 w21 io146ndb3v4 w22 io148ppb3v4 y1 v cci b6 y2 io237ndb6v0 y3 io228ndb5v4 y4 io224ndb5v3 y5 gnd 484-pin fbga pin number a3pe3000l function y6 io220ndb5v3 y7 io220pdb5v3 y8 v cc y9 v cc y10 io200pdb5v0 y11 io192pdb4v4 y12 io188npb4v4 y13 io187psb4v4 y14 v cc y15 v cc y16 io164ndb4v1 y17 io164pdb4v1 y18 gnd y19 io158ppb4v0 y20 io150pdb3v4 y21 io148npb3v4 y22 v cci b3 484-pin fbga pin number a3pe3000l function www..net
package pin assignments 3-18 v1.0 896-pin fbga note for package manufacturing and environmental information, visit the resource center at http://www.actel.com/products/ solutions/pac kage/docs.aspx . note: this is the bottom view. figure 4 ? a1 ball pad corner a b c d e f g h j k l m n p r t u v w y aa ab ac ad ae af 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 ag ah aj ak www..net
military proasic3/el packaging v1.0 3-19 896-pin fbga pin number a3pe3000l function a2 gnd a3 gnd a4 io14npb0v1 a5 gnd a6 io07npb0v0 a7 gnd a8 io09ndb0v1 a9 io17ndb0v2 a10 io17pdb0v2 a11 io21ndb0v2 a12 io21pdb0v2 a13 io33ndb0v4 a14 io33pdb0v4 a15 io35ndb0v4 a16 io35pdb0v4 a17 io41ndb1v0 a18 io43ndb1v0 a19 io43pdb1v0 a20 io45ndb1v0 a21 io45pdb1v0 a22 io57ndb1v2 a23 io57pdb1v2 a24 gnd a25 io69ppb1v3 a26 gnd a27 gbc1/io79ppb1v4 a28 gnd a29 gnd aa1 io256pdb6v2 aa2 io248pdb6v1 aa3 io248ndb6v1 aa4 io246ndb6v1 aa5 gea1/io234pdb6v0 aa6 gea0/io234ndb6v0 aa7 io243ppb6v1 aa8 io245ndb6v1 aa9 geb1/io235ppb6v0 aa10 v cc aa11 io226ppb5v4 aa12 v cci b5 aa13 v cci b5 aa14 v cci b5 aa15 v cci b5 aa16 v cci b4 aa17 v cci b4 aa18 v cci b4 aa19 v cci b4 aa20 io174pdb4v2 aa21 v cc aa22 io142npb3v3 aa23 io144ndb3v3 aa24 io144pdb3v3 aa25 io146ndb3v4 aa26 io146pdb3v4 aa27 io147pdb3v4 aa28 io139ndb3v3 aa29 io139pdb3v3 aa30 io133ndb3v2 ab1 io256ndb6v2 ab2 io244pdb6v1 ab3 io244ndb6v1 ab4 io241pdb6v0 ab5 io241ndb6v0 ab6 io243npb6v1 ab7 v cci b6 ab8 v ccple ab9 v cc ab10 io222pdb5v3 ab11 io218ppb5v3 ab12 io206ndb5v1 ab13 io206pdb5v1 ab14 io198ndb5v0 896-pin fbga pin number a3pe3000l function ab15 io198pdb5v0 ab16 io192ndb4v4 ab17 io192pdb4v4 ab18 io178ndb4v3 ab19 io178pdb4v3 ab20 io174ndb4v2 ab21 io162npb4v1 ab22 v cc ab23 v ccpld ab24 v cci b3 ab25 io150pdb3v4 ab26 io148pdb3v4 ab27 io147ndb3v4 ab28 io145pdb3v3 ab29 io143pdb3v3 ab30 io137pdb3v2 ac1 io254pdb6v2 ac2 io254ndb6v2 ac3 io240pdb6v0 ac4 gec1/io236pdb6v0 ac5 io237pdb6v0 ac6 io237ndb6v0 ac7 v comple ac8 gnd ac9 io226npb5v4 ac10 io222ndb5v3 ac11 io216npb5v2 ac12 io210npb5v2 ac13 io204ndb5v1 ac14 io204pdb5v1 ac15 io194ndb5v0 ac16 io188ndb4v4 ac17 io188pdb4v4 ac18 io182ppb4v3 ac19 io170npb4v2 ac20 io164ndb4v1 896-pin fbga pin number a3pe3000l function www..net
package pin assignments 3-20 v1.0 ac21 io164pdb4v1 ac22 io162ppb4v1 ac23 gnd ac24 v compld ac25 io150ndb3v4 ac26 io148ndb3v4 ac27 gda1/io153pdb3v4 ac28 io145ndb3v3 ac29 io143ndb3v3 ac30 io137ndb3v2 ad1 gnd ad2 io242npb6v1 ad3 io240ndb6v0 ad4 gec0/io236ndb6v0 ad5 v cci b6 ad6 gndq ad6 gndq ad7 v cc ad8 vmv5 ad9 v cci b5 ad10 io224ppb5v3 ad11 io218npb5v3 ad12 io216ppb5v2 ad13 io210ppb5v2 ad14 io202ppb5v1 ad15 io194pdb5v0 ad16 io190pdb4v4 ad17 io182npb4v3 ad18 io176ndb4v2 ad19 io176pdb4v2 ad20 io170ppb4v2 ad21 io166pdb4v1 ad22 v cci b4 ad23 tck ad24 v cc ad25 trst 896-pin fbga pin number a3pe3000l function ad26 v cci b3 ad27 gda0/io153ndb3v4 ad28 gdc0/io151ndb3v4 ad29 gdc1/io151pdb3v4 ad30 gnd ae1 io242ppb6v1 ae2 v cc ae3 io239pdb6v0 ae4 io239ndb6v0 ae5 vmv6 ae5 vmv6 ae6 gnd ae7 gndq ae8 io230ndb5v4 ae9 io224npb5v3 ae10 io214npb5v2 ae11 io212ndb5v2 ae12 io212pdb5v2 ae13 io202npb5v1 ae14 io200ndb5v0 ae15 io196pdb5v0 ae16 io190ndb4v4 ae17 io184pdb4v3 ae18 io184ndb4v3 ae19 io172pdb4v2 ae20 io172ndb4v2 ae21 io166ndb4v1 ae22 io160pdb4v0 ae23 gndq ae24 vmv4 ae25 gnd ae26 gdb0/io152ndb3v4 ae27 gdb1/io152pdb3v4 ae28 vmv3 ae28 vmv3 ae29 v cc 896-pin fbga pin number a3pe3000l function ae30 io149pdb3v4 af1 gnd af2 io238ppb6v0 af3 v cci b6 af4 io220npb5v3 af5 v cc af6 io228ndb5v4 af7 v cci b5 af8 io230pdb5v4 af9 io229ndb5v4 af10 io229pdb5v4 af11 io214ppb5v2 af12 io208ndb5v1 af13 io208pdb5v1 af14 io200pdb5v0 af15 io196ndb5v0 af16 io186ndb4v4 af17 io186pdb4v4 af18 io180ndb4v3 af19 io180pdb4v3 af20 io168ndb4v1 af21 io168pdb4v1 af22 io160ndb4v0 af23 io158npb4v0 af24 v cci b4 af25 io154npb4v0 af26 v cc af27 tdo af28 v cci b3 af29 gndq af29 gndq af30 gnd ag1 io238npb6v0 ag2 v cc ag3 io232npb5v4 ag4 gnd 896-pin fbga pin number a3pe3000l function www..net
military proasic3/el packaging v1.0 3-21 ag5 io220ppb5v3 ag6 io228pdb5v4 ag7 io231ndb5v4 ag8 gec2/io231pdb5v4 ag9 io225npb5v3 ag10 io223npb5v3 ag11 io221pdb5v3 ag12 io221ndb5v3 ag13 io205npb5v1 ag14 io199ndb5v0 ag15 io199pdb5v0 ag16 io187ndb4v4 ag17 io187pdb4v4 ag18 io181ndb4v3 ag19 io171ppb4v2 ag20 io165npb4v1 ag21 io161npb4v0 ag22 io159ndb4v0 ag23 io159pdb4v0 ag24 io158ppb4v0 ag25 gdb2/io155pdb4v0 ag26 gda2/io154ppb4v0 ag27 gnd ag28 v jtag ag29 v cc ag30 io149ndb3v4 ah1 gnd ah2 io233npb5v4 ah3 v cc ah4 ff/geb2/io232ppb5 v4 ah5 v cci b5 ah6 io219ndb5v3 ah7 io219pdb5v3 ah8 io227ndb5v4 ah9 io227pdb5v4 896-pin fbga pin number a3pe3000l function ah10 io225ppb5v3 ah11 io223ppb5v3 ah12 io211ndb5v2 ah13 io211pdb5v2 ah14 io205ppb5v1 ah15 io195ndb5v0 ah16 io185ndb4v3 ah17 io185pdb4v3 ah18 io181pdb4v3 ah19 io177ndb4v2 ah20 io171npb4v2 ah21 io165ppb4v1 ah22 io161ppb4v0 ah23 io157ndb4v0 ah24 io157pdb4v0 ah25 io155ndb4v0 ah26 v cci b4 ah27 tdi ah28 v cc ah29 v pump ah30 gnd aj1 gnd aj2 gnd aj3 gea2/io233ppb5v4 aj4 v cc aj5 io217npb5v2 aj6 v cc aj7 io215npb5v2 aj8 io213ndb5v2 aj9 io213pdb5v2 aj10 io209ndb5v1 aj11 io209pdb5v1 aj12 io203ndb5v1 aj13 io203pdb5v1 aj14 io197ndb5v0 aj15 io195pdb5v0 896-pin fbga pin number a3pe3000l function aj16 io183ndb4v3 aj17 io183pdb4v3 aj18 io179npb4v3 aj19 io177pdb4v2 aj20 io173ndb4v2 aj21 io173pdb4v2 aj22 io163ndb4v1 aj23 io163pdb4v1 aj24 io167npb4v1 aj25 v cc aj26 io156npb4v0 aj27 v cc aj28 tms aj29 gnd aj30 gnd ak2 gnd ak3 gnd ak4 io217ppb5v2 ak5 gnd ak6 io215ppb5v2 ak7 gnd ak8 io207ndb5v1 ak9 io207pdb5v1 ak10 io201ndb5v0 ak11 io201pdb5v0 ak12 io193ndb4v4 ak13 io193pdb4v4 ak14 io197pdb5v0 ak15 io191ndb4v4 ak16 io191pdb4v4 ak17 io189ndb4v4 ak18 io189pdb4v4 ak19 io179ppb4v3 ak20 io175ndb4v2 ak21 io175pdb4v2 ak22 io169ndb4v1 896-pin fbga pin number a3pe3000l function www..net
package pin assignments 3-22 v1.0 ak23 io169pdb4v1 ak24 gnd ak25 io167ppb4v1 ak26 gnd ak27 gdc2/io156ppb4v0 ak28 gnd ak29 gnd b1 gnd b2 gnd b3 gaa2/io309ppb7v4 b4 v cc b5 io14ppb0v1 b6 v cc b7 io07ppb0v0 b8 io09pdb0v1 b9 io15ppb0v1 b10 io19ndb0v2 b11 io19pdb0v2 b12 io29ndb0v3 b13 io29pdb0v3 b14 io31ppb0v3 b15 io37ndb0v4 b16 io37pdb0v4 b17 io41pdb1v0 b18 io51ndb1v1 b19 io59pdb1v2 b20 io53pdb1v1 b21 io53ndb1v1 b22 io61ndb1v2 b23 io61pdb1v2 b24 io69npb1v3 b25 v cc b26 gbc0/io79npb1v4 b27 v cc b28 io64npb1v2 b29 gnd 896-pin fbga pin number a3pe3000l function b30 gnd c1 gnd c2 io309npb7v4 c3 v cc c4 gaa0/io00npb0v0 c5 v cci b0 c6 io03pdb0v0 c7 io03ndb0v0 c8 gab1/io01pdb0v0 c9 io05pdb0v0 c10 io15npb0v1 c11 io25ndb0v3 c12 io25pdb0v3 c13 io31npb0v3 c14 io27ndb0v3 c15 io39ndb0v4 c16 io39pdb0v4 c17 io55ppb1v1 c18 io51pdb1v1 c19 io59ndb1v2 c20 io63ndb1v2 c21 io63pdb1v2 c22 io67ndb1v3 c23 io67pdb1v3 c24 io75ndb1v4 c25 io75pdb1v4 c26 v cci b1 c27 io64ppb1v2 c28 v cc c29 gba1/io81ppb1v4 c30 gnd d1 io303ppb7v3 d2 v cc d3 io305npb7v3 d4 gnd d5 gaa1/io00ppb0v0 896-pin fbga pin number a3pe3000l function d6 gac1/io02pdb0v0 d7 io06npb0v0 d8 gab0/io01ndb0v0 d9 io05ndb0v0 d10 io11ndb0v1 d11 io11pdb0v1 d12 io23ndb0v2 d13 io23pdb0v2 d14 io27pdb0v3 d15 io40pdb0v4 d16 io47ndb1v0 d17 io47pdb1v0 d18 io55npb1v1 d19 io65ndb1v3 d20 io65pdb1v3 d21 io71ndb1v3 d22 io71pdb1v3 d23 io73ndb1v4 d24 io73pdb1v4 d25 io74ndb1v4 d26 gbb0/io80npb1v4 d27 gnd d28 gba0/io81npb1v4 d29 v cc d30 gba2/io82ppb2v0 e1 gnd e2 io303npb7v3 e3 v cci b7 e4 io305ppb7v3 e5 v cc e6 gac0/io02ndb0v0 e7 v cci b0 e8 io06ppb0v0 e9 io24ndb0v2 e10 io24pdb0v2 e11 io13ndb0v1 896-pin fbga pin number a3pe3000l function www..net
military proasic3/el packaging v1.0 3-23 e12 io13pdb0v1 e13 io34ndb0v4 e14 io34pdb0v4 e15 io40ndb0v4 e16 io49ndb1v1 e17 io49pdb1v1 e18 io50pdb1v1 e19 io58pdb1v2 e20 io60ndb1v2 e21 io77pdb1v4 e22 io68ndb1v3 e23 io68pdb1v3 e24 v cci b1 e25 io74pdb1v4 e26 v cc e27 gbb1/io80ppb1v4 e28 v cci b2 e29 io82npb2v0 e30 gnd f1 io296ppb7v2 f2 v cc f3 io306pdb7v4 f4 io297pdb7v2 f5 vmv7 f5 vmv7 f6 gnd f7 gndq f8 io12ndb0v1 f9 io12pdb0v1 f10 io10pdb0v1 f11 io16pdb0v1 f12 io22ndb0v2 f13 io30ndb0v3 f14 io30pdb0v3 f15 io36pdb0v4 f16 io48ndb1v0 896-pin fbga pin number a3pe3000l function f17 io48pdb1v0 f18 io50ndb1v1 f19 io58ndb1v2 f20 io60pdb1v2 f21 io77ndb1v4 f22 io72ndb1v3 f23 io72pdb1v3 f24 gndq f25 gnd f26 vmv2 f26 vmv2 f27 io86pdb2v0 f28 io92pdb2v1 f29 v cc f30 io100npb2v2 g1 gnd g2 io296npb7v2 g3 io306ndb7v4 g4 io297ndb7v2 g5 v cci b7 g6 gndq g6 gndq g7 v cc g8 vmv0 g9 v cci b0 g10 io10ndb0v1 g11 io16ndb0v1 g12 io22pdb0v2 g13 io26ppb0v3 g14 io38npb0v4 g15 io36ndb0v4 g16 io46ndb1v0 g17 io46pdb1v0 g18 io56ndb1v1 g19 io56pdb1v1 g20 io66ndb1v3 896-pin fbga pin number a3pe3000l function g21 io66pdb1v3 g22 v cci b1 g23 vmv1 g24 v cc g25 gndq g25 gndq g26 v cci b2 g27 io86ndb2v0 g28 io92ndb2v1 g29 io100ppb2v2 g30 gnd h1 io294pdb7v2 h2 io294ndb7v2 h3 io300ndb7v3 h4 io300pdb7v3 h5 io295pdb7v2 h6 io299pdb7v3 h7 v compla h8 gnd h9 io08ndb0v0 h10 io08pdb0v0 h11 io18pdb0v2 h12 io26npb0v3 h13 io28ndb0v3 h14 io28pdb0v3 h15 io38ppb0v4 h16 io42ndb1v0 h17 io52ndb1v1 h18 io52pdb1v1 h19 io62ndb1v2 h20 io62pdb1v2 h21 io70ndb1v3 h22 io70pdb1v3 h23 gnd h24 v complb h25 gbc2/io84pdb2v0 896-pin fbga pin number a3pe3000l function www..net
package pin assignments 3-24 v1.0 h26 io84ndb2v0 h27 io96pdb2v1 h28 io96ndb2v1 h29 io89pdb2v0 h30 io89ndb2v0 j1 io290ndb7v2 j2 io290pdb7v2 j3 io302ndb7v3 j4 io302pdb7v3 j5 io295ndb7v2 j6 io299ndb7v3 j7 v cci b7 j8 v ccpla j9 v cc j10 io04npb0v0 j11 io18ndb0v2 j12 io20ndb0v2 j13 io20pdb0v2 j14 io32ndb0v3 j15 io32pdb0v3 j16 io42pdb1v0 j17 io44ndb1v0 j18 io44pdb1v0 j19 io54ndb1v1 j20 io54pdb1v1 j21 io76npb1v4 j22 v cc j23 v ccplb j24 v cci b2 j25 io90pdb2v1 j26 io90ndb2v1 j27 gbb2/io83pdb2v0 j28 io83ndb2v0 j29 io91pdb2v1 j30 io91ndb2v1 k1 io288ndb7v1 896-pin fbga pin number a3pe3000l function k2 io288pdb7v1 k3 io304ndb7v3 k4 io304pdb7v3 k5 gab2/io308pdb7v4 k6 io308ndb7v4 k7 io301pdb7v3 k8 io301ndb7v3 k9 gac2/io307ppb7v4 k10 v cc k11 io04ppb0v0 k12 v cci b0 k13 v cci b0 k14 v cci b0 k15 v cci b0 k16 v cci b1 k17 v cci b1 k18 v cci b1 k19 v cci b1 k20 io76ppb1v4 k21 v cc k22 io78ppb1v4 k23 io88ndb2v0 k24 io88pdb2v0 k25 io94pdb2v1 k26 io94ndb2v1 k27 io85pdb2v0 k28 io85ndb2v0 k29 io93pdb2v1 k30 io93ndb2v1 l1 io286ndb7v1 l2 io286pdb7v1 l3 io298ndb7v3 l4 io298pdb7v3 l5 io283pdb7v1 l6 io291ndb7v2 l7 io291pdb7v2 896-pin fbga pin number a3pe3000l function l8 io293pdb7v2 l9 io293ndb7v2 l10 io307npb7v4 l11 v cc l12 v cc l13 v cc l14 v cc l15 v cc l16 v cc l17 v cc l18 v cc l19 v cc l20 v cc l21 io78npb1v4 l22 io104npb2v2 l23 io98ndb2v2 l24 io98pdb2v2 l25 io87pdb2v0 l26 io87ndb2v0 l27 io97pdb2v1 l28 io101pdb2v2 l29 io103pdb2v2 l30 io119ndb3v0 m1 io282ndb7v1 m2 io282pdb7v1 m3 io292ndb7v2 m4 io292pdb7v2 m5 io283ndb7v1 m6 io285pdb7v1 m7 io287pdb7v1 m8 io289pdb7v1 m9 io289ndb7v1 m10 v cci b7 m11 v cc m12 gnd m13 gnd 896-pin fbga pin number a3pe3000l function www..net
military proasic3/el packaging v1.0 3-25 m14 gnd m15 gnd m16 gnd m17 gnd m18 gnd m19 gnd m20 v cc m21 v cci b2 m22 nc m23 io104ppb2v2 m24 io102pdb2v2 m25 io102ndb2v2 m26 io95pdb2v1 m27 io97ndb2v1 m28 io101ndb2v2 m29 io103ndb2v2 m30 io119pdb3v0 n1 io276pdb7v0 n2 io278pdb7v0 n3 io280pdb7v0 n4 io284pdb7v1 n5 io279pdb7v0 n6 io285ndb7v1 n7 io287ndb7v1 n8 io281ndb7v0 n9 io281pdb7v0 n10 v cci b7 n11 v cc n12 gnd n13 gnd n14 gnd n15 gnd n16 gnd n17 gnd n18 gnd n19 gnd 896-pin fbga pin number a3pe3000l function n20 v cc n21 v cci b2 n22 io106ndb2v3 n23 io106pdb2v3 n24 io108pdb2v3 n25 io108ndb2v3 n26 io95ndb2v1 n27 io99ndb2v2 n28 io99pdb2v2 n29 io107pdb2v3 n30 io107ndb2v3 p1 io276ndb7v0 p2 io278ndb7v0 p3 io280ndb7v0 p4 io284ndb7v1 p5 io279ndb7v0 p6 gfc1/io275pdb7v0 p7 gfc0/io275ndb7v0 p8 io277pdb7v0 p9 io277ndb7v0 p10 v cci b7 p11 v cc p12 gnd p13 gnd p14 gnd p15 gnd p16 gnd p17 gnd p18 gnd p19 gnd p20 v cc p21 v cci b2 p22 gcc1/io112pdb2v3 p23 io110pdb2v3 p24 io110ndb2v3 p25 io109ppb2v3 896-pin fbga pin number a3pe3000l function p26 io111npb2v3 p27 io105pdb2v2 p28 io105ndb2v2 p29 gcc2/io117pdb3v0 p30 io117ndb3v0 r1 gfc2/io270pdb6v4 r2 gfb1/io274ppb7v0 r3 v complf r4 gfa0/io273ndb6v4 r5 gfb0/io274npb7v0 r6 io271ndb6v4 r7 gfb2/io271pdb6v4 r8 io269pdb6v4 r9 io269ndb6v4 r10 v cci b7 r11 v cc r12 gnd r13 gnd r14 gnd r15 gnd r16 gnd r17 gnd r18 gnd r19 gnd r20 v cc r21 v cci b2 r22 gcc0/io112ndb2v3 r23 gcb2/io116pdb3v0 r24 io118pdb3v0 r25 io111ppb2v3 r26 io122ppb3v1 r27 gca0/io114npb3v0 r28 v complc r29 gcb1/io113ppb2v3 r30 io115npb3v0 t1 io270ndb6v4 896-pin fbga pin number a3pe3000l function www..net
package pin assignments 3-26 v1.0 t2 v ccplf t3 gfa2/io272ppb6v4 t4 gfa1/io273pdb6v4 t5 io272npb6v4 t6 io267ndb6v4 t7 io267pdb6v4 t8 io265pdb6v3 t9 io263pdb6v3 t10 v cci b6 t11 v cc t12 gnd t13 gnd t14 gnd t15 gnd t16 gnd t17 gnd t18 gnd t19 gnd t20 v cc t21 v cci b3 t22 io109npb2v3 t23 io116ndb3v0 t24 io118ndb3v0 t25 io122npb3v1 t26 gca1/io114ppb3v0 t27 gcb0/io113npb2v3 t28 gca2/io115ppb3v0 t29 v ccplc t30 io121pdb3v0 u1 io268pdb6v4 u2 io264ndb6v3 u3 io264pdb6v3 u4 io258pdb6v3 u5 io258ndb6v3 u6 io257ppb6v2 u7 io261ppb6v3 896-pin fbga pin number a3pe3000l function u8 io265ndb6v3 u9 io263ndb6v3 u10 v cci b6 u11 v cc u12 gnd u13 gnd u14 gnd u15 gnd u16 gnd u17 gnd u18 gnd u19 gnd u20 v cc u21 v cci b3 u22 io120pdb3v0 u23 io128pdb3v1 u24 io124pdb3v1 u25 io124ndb3v1 u26 io126pdb3v1 u27 io129pdb3v1 u28 io127pdb3v1 u29 io125pdb3v1 u30 io121ndb3v0 v1 io268ndb6v4 v2 io262pdb6v3 v3 io260pdb6v3 v4 io252pdb6v2 v5 io257npb6v2 v6 io261npb6v3 v7 io255pdb6v2 v8 io259pdb6v3 v9 io259ndb6v3 v10 v cci b6 v11 v cc v12 gnd v13 gnd 896-pin fbga pin number a3pe3000l function v14 gnd v15 gnd v16 gnd v17 gnd v18 gnd v19 gnd v20 v cc v21 v cci b3 v22 io120ndb3v0 v23 io128ndb3v1 v24 io132pdb3v2 v25 io130ppb3v2 v26 io126ndb3v1 v27 io129ndb3v1 v28 io127ndb3v1 v29 io125ndb3v1 v30 io123pdb3v1 w1 io266ndb6v4 w2 io262ndb6v3 w3 io260ndb6v3 w4 io252ndb6v2 w5 io251ndb6v2 w6 io251pdb6v2 w7 io255ndb6v2 w8 io249ppb6v1 w9 io253pdb6v2 w10 v cci b6 w11 v cc w12 gnd w13 gnd w14 gnd w15 gnd w16 gnd w17 gnd w18 gnd w19 gnd 896-pin fbga pin number a3pe3000l function www..net
military proasic3/el packaging v1.0 3-27 w20 v cc w21 v cci b3 w22 io134pdb3v2 w23 io138pdb3v3 w24 io132ndb3v2 w25 io136npb3v2 w26 io130npb3v2 w27 io141pdb3v3 w28 io135pdb3v2 w29 io131pdb3v2 w30 io123ndb3v1 y1 io266pdb6v4 y2 io250pdb6v2 y3 io250ndb6v2 y4 io246pdb6v1 y5 io247ndb6v1 y6 io247pdb6v1 y7 io249npb6v1 y8 io245pdb6v1 y9 io253ndb6v2 y10 geb0/io235npb6v0 y11 v cc y12 v cc y13 v cc y14 v cc y15 v cc y16 v cc y17 v cc y18 v cc y19 v cc y20 v cc y21 io142ppb3v3 y22 io134ndb3v2 y23 io138ndb3v3 y24 io140ndb3v3 y25 io140pdb3v3 896-pin fbga pin number a3pe3000l function y26 io136ppb3v2 y27 io141ndb3v3 y28 io135ndb3v2 y29 io131ndb3v2 y30 io133pdb3v2 896-pin fbga pin number a3pe3000l function www..net
package pin assignments 3-28 v1.0 part number and revision date part number 51700106-003-0 revised august 2008 datasheet categories categories in order to provide the latest information to designers, some datasheets are published before data has been fully characterized. datasheets are designated as ?product brief,? ?advanced,? and ?production?. the definition of these categories are as follows: product brief the product brief is a summarized version of a datasheet (advanced or production) and contains general product information. this document gives an overvi ew of specific device and family information. advanced this version contains initial estima ted information based on simulation, other products, devices, or speed grades. this information can be used as estimates, but no t for production. this label only applies to the dc and switching characteristics chapter of the datasheet and will only be used when the data ha s not been fully characterized. unmarked (production) this version contains information that is considered to be final. export administration regulations (ear) the products described in this document are subject to the export administration regu lations (ear). they could require an approved export license prio r to export from the united states. an export includes release of product or disclosure of technology to a foreign na tional inside or outside the united states. actel safety critical, life support, and high-reliability applications policy the actel products described in this advanced status document may not have completed acte l?s qualification process. actel may amend or enhance products during the product introduction and qualification process, resulting in changes in device functi onality or performance. it is the resp onsibility of each customer to ensure the fitness of any actel product (but especially a new product) for a particular purpose, including appropriateness for safety-cri tical, life-support, and othe r high-reliabili ty applications. consult actel?s terms and conditions for specific liability exclusions relating to lif e-support applications. a reliab ility report covering all of actel?s products is availabl e on the actel website at http://www.actel.com/documents/ort_report.pdf . actel also offers a variety of enhanced qualification and lot acceptance screen ing procedures. contact your local actel sales office for additional reliability information. www..net
51700106-005-0/ actel corporation 2061 stierlin court mountain view, ca 94043-4655 usa phone 650.318.4200 fax 650.318.4600 actel europe ltd. river court,meadows business park station approach, blackwater camberley surrey gu17 9ab united kingdom phone +44 (0) 1276 609 300 fax +44 (0) 1276 607 540 actel japan exos ebisu buillding 4f 1-24-14 ebisu shibuya-ku tokyo 150 japan phone +81.03.3445.7671 fax +81.03.3445.7668 http://jp.actel.com actel hong kong room 2107, china resources building 26 harbour road wanchai, hong kong phone +852 2185 6460 fax +852 2185 6488 www.actel.com.cn www.actel.com actel and the actel logo are registered trademarks of actel corporation. all other trademarks are the property of their owners. 8.08 www..net

▲Up To Search▲

Price & Availability of A3P1000

	To Download A3P1000 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .